molecalculator

Moles & Molar Mass

Enthalpy of Dry Air: Definition & Calculation

Calculator No. 01-7788 · Updated · Formula and assumptions shown below

Specific enthalpy 25.12 kJ/kg
Enthalpy in BTU/lb
10.80 BTU/lb
= Specific enthalpy × 0.429922
Temperature
25 °C
Set in the form below
Specific heat (constant pressure)
1.005 kJ/(kg·K)
Set in the form below
You enter
Temperature (°C), Specific heat (constant pressure) (kJ/(kg·K))
You get
Specific enthalpy (kJ/kg), Enthalpy in BTU/lb (BTU/lb)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The enthalpy of dry air is the total heat content of air per unit mass, measured relative to a reference state, typically 0°C where its enthalpy is defined as zero. For dry air, enthalpy is calculated as h = cp · T, where cp is the specific heat at constant pressure (approximately 1.005 kJ/(kg·K) for air) and T is the temperature in °C. This calculator computes the specific enthalpy of dry air in kJ/kg and also in BTU/lb for convenience.

Formula

The specific enthalpy of dry air is given by:

h = cp · T

Where:

  • h = specific enthalpy (kJ/kg)
  • cp = specific heat at constant pressure (kJ/(kg·K)) – for dry air, cp ≈ 1.005 kJ/(kg·K) at 25°C, but it varies slightly with temperature (1.004–1.010 kJ/(kg·K) over 0–100°C).
  • T = temperature in °C (since the reference is 0°C, using °C directly is correct).

To convert to BTU/lb, multiply by 0.429922 (since 1 kJ/kg = 0.429922 BTU/lb).

Worked Example

Using the default values: T = 25°C, cp = 1.005 kJ/(kg·K).

Step 1: Apply the formula.

h = 1.005 × 25 = 25.125 kJ/kg

Step 2: Convert to BTU/lb.

h_btu = 25.125 × 0.429922 = 10.80 BTU/lb (rounded to 2 decimals).

The calculator shows 25.13 kJ/kg and 10.80 BTU/lb.

Assumptions

  • Air is treated as a perfect (ideal) gas with constant specific heat.
  • The reference state is 0°C (273.15 K) where enthalpy is defined as 0 kJ/kg.
  • The specific heat value used is for dry air (no water vapor). For moist air, the enthalpy includes the latent heat of water vapor and is more complex.
  • Pressure does not affect enthalpy for an ideal gas, so no pressure input is needed.

Why Enthalpy Matters

Enthalpy is a measure of the total energy of a thermodynamic system, including internal energy plus the product of pressure and volume. In HVAC (heating, ventilation, and air conditioning) engineering, enthalpy is used to calculate the heat load required to heat or cool air. For example, to heat 1 kg of dry air from 20°C to 30°C, you need to add (1.005 × 10) = 10.05 kJ of energy. This is the basis for sizing heaters, coolers, and air handling units.

For moist air (air containing water vapor), the enthalpy includes the sensible heat of the dry air and water vapor plus the latent heat of vaporization. Psychrometric charts show enthalpy lines for moist air, but the dry-air component is always calculated as above.

How to Use the Calculator

Enter the temperature of the dry air in degrees Celsius. The specific heat is pre-filled with 1.005 kJ/(kg·K), which is accurate for typical room temperatures (0–40°C). For higher temperatures (e.g., industrial dryers up to 200°C), you may adjust cp to 1.010 kJ/(kg·K) for better accuracy. The calculator returns the specific enthalpy in kJ/kg and BTU/lb.

To get total enthalpy (in kJ), multiply the specific enthalpy by the mass of air in kg. For example, 2 kg of air at 25°C has a total enthalpy of 25.13 × 2 = 50.26 kJ.

Common Mistakes and Misconceptions

  • Using Kelvin instead of Celsius: Since the reference is 0°C, using Kelvin (T+273.15) would give an enthalpy relative to absolute zero, which is not the standard convention. Always use °C.
  • Confusing with internal energy: Enthalpy includes the pressure-volume work, but for an ideal gas, h = u + RT. The difference is significant at high temperatures.
  • Ignoring humidity: This calculator is for dry air only. For moist air, the enthalpy is higher due to water vapor. At 25°C and 50% relative humidity, the enthalpy of moist air is about 50 kJ/kg, roughly double that of dry air.
  • Assuming cp is constant: Over a wide temperature range (e.g., -50°C to 200°C), cp varies by about 1%. For most engineering calculations, 1.005 is fine.

Limits of the Formula

The linear formula h = cp·T is valid for ideal gases with constant specific heat. Real air deviates slightly at very high pressures (above 10 atm) or very low temperatures (near liquefaction). For combustion or high-temperature processes (above 1000°C), the specific heat changes significantly due to vibrational modes and dissociation, so a temperature-dependent cp or tabulated enthalpy data should be used. For HVAC applications, the formula is accurate to within 0.5%.

Frequently Asked Questions

Q: What is the enthalpy of dry air at 0°C?
A: By definition, it is 0 kJ/kg. This is the reference point for most psychrometric charts.

Q: How do I convert enthalpy from kJ/kg to BTU/lb?
A: Multiply by 0.429922. For example, 25 kJ/kg × 0.429922 = 10.75 BTU/lb.

Q: Why does moist air have higher enthalpy than dry air at the same temperature?
A: Moist air contains water vapor, which carries latent heat. The enthalpy of moist air is the sum of dry air enthalpy plus the enthalpy of water vapor, which includes the heat of vaporization (about 2500 kJ/kg of water).

Q: Can I use this calculator for air at high pressure?
A: For pressures up to about 10 atm, the ideal gas assumption holds, and enthalpy is nearly independent of pressure. Beyond that, real gas effects become significant, and you should use a real gas equation of state.

Q: What is the difference between specific heat at constant pressure (cp) and constant volume (cv)?
A: cp is used for enthalpy because enthalpy is defined at constant pressure. cv is used for internal energy. For air, cp ≈ 1.005 kJ/(kg·K) and cv ≈ 0.718 kJ/(kg·K). The difference is the gas constant R = 0.287 kJ/(kg·K).

Q: How does altitude affect air enthalpy?
A: For dry air, enthalpy depends only on temperature, not on pressure or altitude. However, at higher altitudes, the air density is lower, so the total enthalpy per cubic meter is lower, but per kilogram it remains the same.

Related

Formula used
in t | Temperature | °C | 25 | -273.15 | 2000
in cp | Specific heat (constant pressure) | kJ/(kg·K) | 1.005 | 0 | 10
out h | Specific enthalpy | kJ/kg | cp * t | 2
out h_btu | Enthalpy in BTU/lb | BTU/lb | h * 0.429922 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →