molecalculator

Moles & Molar Mass

Exponential Decay Equation and Calculator

Calculator No. 01-5022 · Updated · Formula and assumptions shown below

Remaining amount 36.79 units
Fraction remaining
0.3679 fraction
Result, rounded to 4 decimal places
Percentage remaining
36.79 %
Result, rounded to 2 decimal places
Half-life
6.9315 time units
Result, rounded to 4 decimal places
You enter
Initial amount (units), Decay constant (1/time unit), Elapsed time (time units)
You get
Remaining amount (units), Fraction remaining (fraction), Percentage remaining (%), Half-life (time units)
Rounding
2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The exponential decay equation is N(t) = N₀e−kt, where N₀ is the starting amount, k is the positive decay constant, and t is elapsed time. This calculator uses those three values to find the remaining amount, the half-life, and the percentage remaining under a constant-rate decay model.

Formula

The remaining amount equals the initial amount multiplied by the exponential of negative decay constant times elapsed time:

N(t) = N₀e−kt

  • N(t) is the amount remaining at time t, in the same units as the initial amount.
  • N₀ is the amount at the chosen starting time, in any consistent unit such as grams, atoms, or concentration.
  • k is the decay constant, expressed as the reciprocal of the time unit—for example, s−1 if time is measured in seconds.
  • t is elapsed time, using the time unit paired with k.
  • e is Euler’s number, approximately 2.71828.

The calculator also reports the fraction remaining, the percentage remaining, and half-life. The half-life is t1/2 = ln(2)/k. The input time unit is arbitrary, but the units of k and t must match. For example, a rate in days−1 must be combined with time in days.

Worked Example

Using the calculator’s default values, take an initial amount of 100 units, a decay constant of 0.1 per time unit, and elapsed time of 10 time units.

  1. Calculate the exponent: −k × t = −0.1 × 10 = −1.
  2. Calculate the remaining fraction: e−1 = 0.3678794412.
  3. Calculate the remaining amount: 100 × 0.3678794412 = 36.78794412 units, which rounds to 36.79 units.
  4. Convert the fraction to a percentage: 100 × 0.3678794412 = 36.78794412%, or 36.79%.
  5. Calculate half-life: ln(2) / 0.1 = 6.931471806 time units, or 6.9315 time units.

Assumptions

  • The decay constant stays constant over the period being modeled.
  • The amount follows a continuous, first-order exponential decay process.
  • The starting amount and remaining amount use the same units.
  • The decay constant is nonnegative; zero means no decay and an infinite half-life is not represented by this calculator.

How Exponential Decay Works

In exponential decay, the amount lost over a short interval is proportional to the amount present at that moment. A large starting quantity therefore loses more in absolute terms than a small one, even though both lose the same fraction over equal time intervals. The rate is not a fixed number of units per hour or year; it is a fixed proportion per unit time.

The differential equation behind the model is dN/dt = −kN. Its solution is N(t) = N₀e−kt. The negative sign indicates that the amount decreases when k is positive. The decay constant sets how quickly the decrease occurs: larger k means faster decay and a shorter half-life.

The equation describes a smooth average. For radioactive decay, the exact time at which any individual unstable nucleus decays is random, while the equation predicts the expected behavior of a large population. The same mathematical pattern also appears in some cooling, chemical, biological, and engineering models when their conditions make a constant proportional rate a reasonable approximation.

Half-Life, Rate, and Other Forms

Half-life is often easier to measure or communicate than a decay constant. If the half-life is known, use k = ln(2)/t1/2. After each half-life, half of the amount then present remains. Thus, after two half-lives one quarter remains; after three, one eighth remains. Equal time intervals produce equal fractional reductions, not equal absolute reductions.

The equation can also be rearranged to solve for elapsed time: t = ln(N₀/N)/k, provided the remaining amount is positive and no greater than the initial amount. To find the decay constant from two measurements, use k = ln(N₀/N(t))/t for positive elapsed time. Real measurements may be noisy, so a rate estimated from one pair of observations can differ from a fitted rate based on many observations.

When to Use This Model

Use exponential decay when evidence or a well-established model supports a constant fractional loss rate. It can be useful for estimating what remains after a known time, translating between a decay constant and half-life, or comparing decay rates under compatible conditions. The calculator handles the arithmetic; it cannot determine whether exponential decay is a suitable model for a particular substance or process.

Check the following before using a result:

  • Confirm that the decay constant and elapsed time use reciprocal, matching units.
  • Use the same definition of “amount” at the start and end, such as mass, particle count, or concentration.
  • Verify that the constant-rate assumption applies across the full time span.
  • Keep enough precision in the rate and time inputs; rounding intermediate values can noticeably shift a result over long periods.

Common Misunderstandings and Limits

A common mistake is to treat k as the fraction lost during one time unit. It is a rate constant, not generally a percentage. For example, with k = 0.1 per day, the amount after one day is multiplied by e−0.1, about 0.9048, so roughly 9.52% is lost—not exactly 10%.

Another mistake is to assume that a half-life means the material disappears after a fixed number of half-lives. The formula approaches zero without reaching it at any finite time when the initial amount and rate are finite. Also, a negative input for k would describe exponential growth in this equation, not decay; this calculator restricts the rate to nonnegative values.

Real systems may depart from the model if their rate changes with temperature, concentration, environment, or time, or if several processes with different rates act together. A graph that curves on ordinary linear axes may appear as a straight line on a plot of ln(N) against time for a single exponential process. If observations systematically diverge from the model, do not force a single decay constant to explain them.

Frequently Asked Questions

What is the basic equation for exponential decay?
N(t) = N₀e−kt. It gives the amount remaining after elapsed time t, assuming a constant proportional decay rate.

How do I calculate the decay constant from half-life?
Use k = ln(2)/t1/2. Express the half-life in the time unit you want to use; the resulting constant has the reciprocal unit.

What does the decay constant mean?
It describes the proportional decay rate per unit time. A larger positive value means faster decay, but it is not automatically the exact percentage lost in one time unit.

Can exponential decay reach zero?
In the mathematical model, it gets arbitrarily close to zero but does not reach zero at a finite time. In practice, measurements may become too small to detect or a count may reach zero by chance.

Does the equation work for radioactive decay?
Yes. It describes the expected remaining quantity for a radioactive population with a constant decay rate. Individual nuclear decays are random, so small samples can fluctuate around the predicted average.

Related

Formula used
in n0 | Initial amount | units | 100 | 0
in k | Decay constant | 1/time unit | 0.1 | 0
in t | Elapsed time | time units | 10 | 0
out n | Remaining amount | units | n0 * exp(-k * t) | 2
out f | Fraction remaining | fraction | exp(-k * t) | 4
out p | Percentage remaining | % | 100 * exp(-k * t) | 2
out h | Half-life | time units | ln(2) / k | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →