molecalculator

Moles & Molar Mass

Molarity From Density and Mass Percent

Calculator No. 01-4780 · Updated · Formula and assumptions shown below

Molarity 3.765 mol/L
Concentration in millimolar
3,764.5 mM
= Molarity × 1000
Solution density
1.1 g/mL
Set in the form below
Solute mass percent
20 %
Set in the form below
You enter
Solution density (g/mL), Solute mass percent (%), Solute molar mass (g/mol)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
3 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To find molarity from a solution’s density and mass percent, use M = (ρ × 1000 × w) / MM, where ρ is density in g/mL, w is the mass fraction of solute, and MM is its molar mass in g/mol. Enter density, mass percent, and molar mass; the calculator returns molarity in mol/L and concentration in mM.

Formula

M = (ρ × 1000 × w) / MM, with w = p/100. Here, M is molarity in mol/L, ρ is solution density in g/mL, 1000 converts mL to L, w is the solute’s mass fraction (unitless), p is mass percent, and MM is solute molar mass in g/mol. The density is for the whole solution, not the pure solvent. The calculation treats a 1 L portion as the basis: its mass is ρ × 1000 grams, and the solute accounts for fraction w of that mass. Dividing the solute mass by its molar mass gives moles in that litre.

For example, 20% by mass means 20 g of solute per 100 g of solution, so w = 0.20. It does not mean 20 g per 100 g of solvent. Keeping that distinction is essential to using the density correctly.

Worked Example

Using the calculator defaults—density 1.10 g/mL, mass percent 20%, and molar mass 58.44 g/mol:

  1. Convert mass percent to mass fraction: w = 20 / 100 = 0.20.
  2. Find the mass of one litre of solution: 1.10 g/mL × 1000 mL/L = 1100 g/L.
  3. Find the solute mass in that litre: 1100 g/L × 0.20 = 220 g/L.
  4. Convert solute mass to amount: 220 g/L ÷ 58.44 g/mol = 3.7645 mol/L.

The displayed molarity is 3.765 mol/L (rounded to three decimal places). The millimolar result is 3.7645 × 1000 = 3764.5 mM, displayed to one decimal place.

Assumptions

  • The stated density applies to the solution at the conditions relevant to the concentration, especially its temperature.
  • The mass percent is the mass of the specified solute divided by total solution mass, multiplied by 100.
  • The molar mass describes that solute and is entered in g/mol.
  • The method uses the final solution volume implied by its density; it does not treat solvent volume as final volume.

When This Conversion Is Useful

This conversion is useful when a solution is labelled by mass percent but a calculation needs mol/L—for example, comparing concentration units or working through a stoichiometry exercise. Mass percent is based on weighing, while molarity is based on volume. Density connects the two by converting a known volume of solution into its mass.

To apply it reliably, identify the exact solute and check the concentration convention on the label or data source. Then obtain density for the solution at a stated or appropriate temperature and use the compound’s molar mass. If the supplied density is in kg/L, its numerical value is equal to g/mL; if it is in g/L, divide by 1000 to obtain g/mL before entering it. Do not enter solvent density in place of solution density.

Choosing Inputs and Interpreting the Result

  • Density: Use the density of the complete solution, not a handbook value for pure water or another solvent. If the density is temperature-specific, use the value matching the stated conditions as closely as possible.
  • Mass percent: Enter the numerical percentage, such as 20 for 20%, not 0.20. The calculator converts it to a fraction by dividing by 100.
  • Molar mass: Use the chemical formula and the appropriate atomic weights. For a hydrate, include water of crystallization; for a mixture or a substance with variable composition, a single molar mass may not be suitable.

Molarity describes moles of solute per litre of final solution. The mM result is the same concentration expressed in millimoles per litre: 1 mol/L = 1000 mM. A large molarity does not imply that a solution is ideal or that its ions are fully dissociated; those are separate chemical considerations.

Common Errors and Limits

  • Using solvent mass percent: A 20% w/w solution contains 20 g solute per 100 g of solution, not per 100 g of solvent.
  • Skipping the factor of 100: Convert percent to a mass fraction. Using 20 instead of 0.20 makes the result 100 times too large.
  • Mixing volume units: The factor 1000 in the formula converts the 1 L basis to 1000 mL. If density is supplied in another unit, convert it first.
  • Rounding too early: Keep the input values and intermediate calculations at their available precision, then round the final result to a precision justified by the source data.

The result is only as accurate as the density, percentage, and molar mass inputs. Density changes with temperature, and some concentrated solutions may have composition-dependent properties or ambiguous labels. The formula converts concentration units; it does not correct for impurities, chemical reactions, dissociation, or uncertainty in the source data. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is the formula for molarity from density and mass percent?
Use M = (ρ × 1000 × p/100) / MM when density is in g/mL, p is the numerical mass percent, and molar mass is in g/mol. The answer is in mol/L.

Does mass percent mean grams per 100 mL?
No. Mass percent, often written % w/w, means grams of solute per 100 grams of total solution. Grams per 100 mL is a mass-per-volume concentration and needs a different interpretation.

Can I calculate molarity from mass percent alone?
Not generally. You also need the solution density to convert solution mass into volume, and the solute’s molar mass to convert grams of solute into moles.

Why does temperature matter?
Solution volume and density can change with temperature. Since molarity is defined per litre of solution, a density value measured at a different temperature can shift the calculated result.

Is molarity the same as molality?
No. Molarity is moles of solute per litre of solution; molality is moles of solute per kilogram of solvent. They use different denominators and are not interchangeable.

Related

Formula used
in rho | Solution density | g/mL | 1.10 | 0
in pct | Solute mass percent | % | 20 | 0
in mm | Solute molar mass | g/mol | 58.44 | 0
out c | Molarity | mol/L | rho * 1000 * (pct / 100) / mm | 3
out cm | Concentration in millimolar | mM | c * 1000 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →