molecalculator

Moles & Molar Mass

Concentration Equation: Formula and Worked Example

Calculator No. 01-3767 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The concentration equation depends on how concentration is expressed. For molarity, the standard equation is M = n / V, where n is the amount of solute in moles and V is the final solution volume in liters. This calculator finds molarity and millimolar concentration from a solute’s mass, its molar mass, and the final solution volume.

Formula

The calculator first converts solute mass to moles, then divides by the solution’s volume in liters:

c = (m / Mr) / (VmL / 1000)

  • c is molar concentration, or molarity, in mol/L.
  • m is the solute mass in grams (g).
  • Mr is the solute’s molar mass in grams per mole (g/mol).
  • VmL is the final solution volume in milliliters (mL). Dividing by 1000 converts milliliters to liters.

The second output uses the relationship concentration in mM = c × 1000, because 1 mol/L equals 1000 mmol/L, or 1000 mM. Here, mmol means millimoles.

Worked Example

For the calculator’s defaults, the solute mass is 2.922 g, the molar mass is 58.44 g/mol, and the final solution volume is 250 mL.

  1. Convert mass to amount: n = 2.922 g / 58.44 g/mol = 0.050000 mol.
  2. Convert volume to liters: 250 mL / 1000 = 0.25000 L.
  3. Divide moles by volume: c = 0.050000 mol / 0.25000 L = 0.2000 mol/L.
  4. Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM.

The displayed outputs are therefore 0.2000 mol/L and 200.00 mM.

Assumptions

  • The entered volume is the final solution volume, not the volume of solvent used before dissolving the solute.
  • The mass refers to the solute whose molar mass is entered; the solute’s identity and composition are assumed known.
  • The calculation reports analytical molarity from the amount added. It does not account for reaction, degradation, purity, or changes in chemical form.
  • No temperature correction or activity-coefficient correction is applied.

What Concentration Means

Concentration describes how much of one substance, the solute, is present in a stated amount of a mixture or solution. The appropriate equation depends on what is being measured and how the result must be reported. Molarity is widely used in chemistry because it expresses the number of moles of solute per liter of solution.

Other common concentration measures answer different questions. Mass concentration is mass per volume, such as g/L. Mass fraction compares solute mass with total solution mass, often as a percentage. Mole fraction compares the moles of one component with total moles. These quantities are not interchangeable without additional information, such as molar mass or solution density.

Choosing the Right Equation

Use the form that matches the information available and the requested unit:

  • Molarity: M = n/V, with moles divided by final solution volume in liters.
  • Moles from mass: n = m/Mr, with mass in grams and molar mass in g/mol.
  • Mass concentration: mass concentration = solute mass / solution volume, with compatible units such as g/L.
  • Mass percent: mass percent = (solute mass / total solution mass) × 100%.
  • Dilution of the same solute: C1V1 = C2V2, when the amount of solute is conserved and the concentration and volume units are consistent.

Do not use the dilution equation to calculate a new concentration when a chemical reaction consumes or produces the solute. In that situation, reaction stoichiometry may be needed to determine the amount remaining or formed.

Using and Interpreting the Result

To use the calculator, enter the solute mass, the molar mass for the correct chemical form, and the final solution volume. The result is mol/L; the millimolar output is the same concentration expressed in mmol/L. For example, 0.2000 mol/L is equivalent to 200.00 mM.

Molar mass depends on the compound’s formula and can differ between related forms, such as a hydrated salt and its anhydrous form. Use the value matching the substance being counted. If a reagent is not completely pure, the weighed mass may not equal the mass of the intended solute; accounting for purity requires reliable purity information and a corresponding correction.

Common Errors and Limits

The most frequent mistake is using the solvent volume instead of the final solution volume. If a solute is dissolved in 250 mL of water, the final solution volume may not be exactly 250 mL. Molarity uses the volume after the solute has dissolved and the solution has been brought to its intended final volume.

  • Mixing units: convert mL to L by dividing by 1000. Using 250 as though it were liters would produce a result that is 1000 times too small.
  • Using the wrong molar mass: check the chemical formula, hydrate state, and units. A molar mass in kg/mol must not be entered as though it were g/mol.
  • Rounding too early: retain useful digits during intermediate calculations and round the final result to match the precision of the measurements.
  • Confusing molarity and molality: molarity is moles per liter of solution; molality is moles per kilogram of solvent. They differ, especially when temperature or density changes matter.

Molarity is volume-based, so the measured volume can vary with temperature. For more precise work, use the temperature and preparation convention specified by the relevant method. This arithmetic also assumes the entered quantities are accurate; it does not estimate measurement uncertainty or determine the concentration of a mixture with unknown composition. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is the basic equation for concentration?
The basic molarity equation is M = n/V: divide the amount of solute in moles by the final solution volume in liters. Other concentration units use different equations.

How do I calculate concentration from mass?
Divide the mass by molar mass to find moles, then divide those moles by final solution volume in liters: c = (m/Mr)/V.

Why must the volume be in liters?
Molarity is defined in moles per liter. Convert milliliters to liters by dividing by 1000 before using the equation.

Is concentration the same as molarity?
No. Concentration is a general term. Molarity is one specific measure: moles of solute per liter of solution.

Does temperature affect molarity?
It can. A solution’s volume can change with temperature, affecting moles per liter even if the amount of solute stays the same.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →