molecalculator

Moles & Molar Mass

Equivalent Inductance Calculator & Formula

Calculator No. 01-8463 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

An equivalent inductance calculator determines the total inductance of a network of inductors connected in series or parallel. You enter the individual inductance values (in henries, millihenries, or microhenries) and the connection type, and it returns the single inductance value that would replace the entire network without changing the circuit’s behavior. This tool is essential for designing filters, power supplies, and RF circuits where exact inductance matters.

Formula

For inductors in series, the equivalent inductance is the sum of all individual inductances:

Leq = L1 + L2 + L3 + … + Ln

For inductors in parallel, the reciprocal of the equivalent inductance is the sum of the reciprocals of each inductance:

1/Leq = 1/L1 + 1/L2 + 1/L3 + … + 1/Ln

Where:

  • Leq = equivalent inductance (henries, H)
  • L1, L2, …, Ln = individual inductances (H)

All values must be in the same unit before applying the formula. The calculator above uses microhenries (µH) for convenience, but the math is unit-agnostic.

Worked Example

Using the default values: L1 = 10 µH, L2 = 20 µH, L3 = 30 µH.

Series:

Leq = 10 + 20 + 30 = 60 µH

Parallel:

1/Leq = 1/10 + 1/20 + 1/30 = 0.1 + 0.05 + 0.03333 = 0.18333 µH−1

Leq = 1 / 0.18333 ≈ 5.4545 µH

The calculator returns 60 µH for series and 5.4545 µH for parallel, matching these calculations.

Assumptions

  • Inductors are ideal – no mutual inductance (no magnetic coupling between them).
  • Inductors have negligible resistance and parasitic capacitance.
  • All inductors are linear (constant inductance regardless of current).
  • The operating frequency is within the inductors’ intended range.

Why Equivalent Inductance Matters

In circuit design, you rarely find an inductor with the exact value you need. Combining standard-value inductors in series or parallel lets you achieve custom inductances. Series connections are used when you need a larger inductance than any single part provides – for example, adding a 10 µH and a 4.7 µH to get 14.7 µH. Parallel connections are useful when you need a smaller inductance or when you want to split current between multiple inductors to reduce heating.

Equivalent inductance also appears in analyzing transformer circuits, coupled inductors, and filter networks. For instance, a simple LC low-pass filter’s cutoff frequency depends directly on the total inductance in the circuit, so knowing the equivalent value is critical for predicting performance.

How to Choose the Right Connection

Deciding between series and parallel depends on your target inductance and other constraints:

  • Series – Use when you need a value larger than any available inductor. The total is always greater than the largest individual value. This also increases the total series resistance (ESR) and may lower the self-resonant frequency.
  • Parallel – Use when you need a value smaller than any available inductor. The total is always less than the smallest individual value. Parallel connection reduces the effective series resistance and can improve current handling, but it also reduces the total inductance.

Also consider tolerance. If you need a precise value, using a series combination of a fixed inductor and a trimmer (variable) inductor gives you adjustability. For high-current applications, parallel inductors share the current, but ensure they are identical to avoid uneven current distribution.

Common Mistakes and Misconceptions

A frequent error is confusing the parallel formula with the series one. Remember: for inductors in parallel, you add reciprocals, not the values themselves. Another mistake is forgetting to convert units – mixing henries and millihenries in the same calculation yields a wrong answer by a factor of 1000.

Many people also assume that the equivalent inductance of parallel inductors is simply half of one value (like two identical resistors in parallel), but that only works when the inductors are equal. For unequal values, you must use the full reciprocal formula.

One common misconception is that the equivalent inductance of series inductors is always larger than that of parallel inductors. While true for positive values, this ignores that mutual inductance can alter the result. If two inductors are magnetically coupled (e.g., on a shared core), the series inductance becomes L1 + L2 ± 2M, where M is the mutual inductance. The calculator here assumes no coupling.

Comparison with Resistors and Capacitors

Inductors follow the same combination rules as resistors for series (sum) and parallel (reciprocal sum). Capacitors are the opposite: series uses reciprocal sum, parallel uses sum. This is a common source of confusion because all three components appear in similar circuits. The physical reason is that inductors in series have the same current, so their voltages add, while in parallel they have the same voltage, so currents add – leading to the reciprocal rule.

When designing a circuit, always double-check which component you’re combining. A quick mental test: if you put two equal inductors in series, the total is double – that matches the resistor rule. If you put two equal capacitors in series, the total is half – that’s the reciprocal rule.

Practical Considerations and Limitations

Real inductors have parasitic capacitance between windings, which causes the impedance to peak at the self-resonant frequency (SRF). Above the SRF, an inductor behaves like a capacitor. Therefore, the equivalent inductance formula only holds well below the SRF. Additionally, inductors have a rated saturation current – beyond this, the inductance drops sharply because the core saturates. When combining inductors, the saturation current of the combination is not simply the sum of individual ratings; it depends on the current sharing.

For high-frequency RF work, the physical layout matters. Two inductors placed close together may couple magnetically, changing the effective inductance. To minimize coupling, place them perpendicular or with a shield between them. In power electronics, the core material also affects inductance stability with temperature and DC bias – always check the datasheet.

If you are designing a circuit for production, remember that inductor tolerances are typically ±10% or ±20%. A series combination of two 10% inductors can yield a total that deviates by up to 20% from the nominal value. For precision applications, measure the actual inductance with an LCR meter after assembly.

Frequently Asked Questions

Can I use this calculator for inductors with mutual coupling?
No. The formulas assume zero mutual inductance. For coupled inductors (e.g., a transformer), you need to know the coupling coefficient k and use Leq = L1 + L2 ± 2M, where M = k√(L1L2).

What if I have more than three inductors?
The calculator supports up to three, but the formulas extend to any number. For series, just add all values. For parallel, add the reciprocals of all values and take the reciprocal of the sum. You can use this calculator iteratively: combine two, then combine the result with the next, and so on.

Why does the parallel inductance come out smaller than the smallest inductor?
Because in parallel, each inductor provides an additional current path, reducing the overall opposition to current change. Mathematically, the reciprocal sum is larger than any individual reciprocal, so the equivalent is smaller. This is exactly like resistors in parallel.

Does the unit (µH, mH, H) affect the result?
No, as long as you use the same unit for all inductors. The formula is scale-invariant. The calculator here uses µH, but you can enter values in any unit and interpret the result in that same unit.

What is the difference between equivalent inductance and total inductance?
They are the same thing. Equivalent inductance is the single inductance that replaces the network; total inductance is the sum in series or the reciprocal sum in parallel. Both terms are used interchangeably.

Can I combine inductors in series and parallel in the same circuit?
Yes, but you must reduce the network step by step. For example, if you have two in parallel and that combination is in series with a third, first find the parallel equivalent, then add the series value. The calculator above handles only pure series or pure parallel, so for mixed networks you’ll need to do multiple calculations.

Related

Formula used
in l1 | Inductor 1 | µH | 10 | 0 | -
in l2 | Inductor 2 | µH | 20 | 0 | -
in l3 | Inductor 3 | µH | 30 | 0 | -
sel conn | Connection | Series=1, Parallel=2
out leq | Equivalent inductance | µH | conn == 1 ? l1 + l2 + l3 : 1 / (1/l1 + 1/l2 + 1/l3) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →