molecalculator

Moles & Molar Mass

Gas Volume Factor: Definition and Calculation

Calculator No. 01-5635 · Updated · Formula and assumptions shown below

Gas formation volume factor 0.0112 m³/standard m³
Gas formation volume factor
0.0112 reservoir ft³/standard ft³
= Gas formation volume factor
Reservoir pressure
10000 kPa absolute
Set in the form below
Reservoir temperature
80 °C
Set in the form below
You enter
Reservoir pressure (kPa absolute), Reservoir temperature (°C), Gas deviation factor Z, Standard pressure (kPa absolute), Standard temperature (°C)
You get
Gas formation volume factor (m³/standard m³), Gas formation volume factor (reservoir ft³/standard ft³)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Gas volume factor describes how much a specified amount of gas occupies under stated pressure and temperature conditions. In petroleum engineering, the gas formation volume factor, usually written Bg, is the reservoir volume occupied by a given amount of gas divided by its volume at standard conditions; this calculator estimates Bg for an ideal gas from pressure, temperature, and the gas deviation factor.

Formula

The gas formation volume factor is the volume occupied by gas at reservoir conditions divided by its volume at the selected standard conditions. For the same quantity of gas, the real-gas equation gives:

Bg = [Z Tr / Pr] / [Ts / Ps]

  • Bg is the gas formation volume factor, expressed here as reservoir cubic metres per standard cubic metre.
  • Z is the dimensionless gas compressibility (deviation) factor at reservoir conditions.
  • Tr is reservoir absolute temperature in kelvins, calculated as °C + 273.15.
  • Pr is reservoir absolute pressure in kilopascals.
  • Ts and Ps are the chosen standard absolute temperature in kelvins and pressure in kilopascals.

The calculator converts each Celsius temperature to kelvins by adding 273.15. It uses pressure in kPa throughout, so the pressure units cancel in the ratio. It reports a dimensionless volume ratio with the stated reservoir-to-standard units. The result in ft³/standard ft³ has the same numerical value because both volumes are converted by the same cubic-length factor.

Worked Example

Using the calculator defaults: reservoir pressure is 10,000 kPa absolute, reservoir temperature is 80 °C, Z is 0.9, standard pressure is 101.325 kPa absolute, and standard temperature is 15.56 °C.

  1. Convert temperatures: Tr = 80 + 273.15 = 353.15 K; Ts = 15.56 + 273.15 = 288.71 K.
  2. Apply the formula: Bg = [0.9 × 353.15 / 10000] / [288.71 / 101.325].
  3. Evaluate: Bg = 0.0317835 / 2.84863 = 0.011156 m³/standard m³, rounded to four decimal places.

The four-decimal calculator output is 0.0112 m³/standard m³. In reservoir cubic feet per standard cubic foot, the ratio is likewise 0.0112. That means one standard cubic metre of gas corresponds to about 0.0112 cubic metres at the specified reservoir conditions under these inputs.

Assumptions

  • The gas follows the real-gas equation of state using the supplied Z factor; Z is not assumed to equal 1.
  • Pressure inputs are absolute, not gauge. Temperature inputs are Celsius and are converted to kelvins.
  • The selected standard conditions are 101.325 kPa and 15.56 °C. These are calculator defaults, not a universal definition of standard conditions.
  • The gas amount is unchanged between the standard and reservoir states, with no phase change, leakage, or compositional change.
  • The supplied Z factor represents reservoir conditions. This simple calculation does not determine Z from gas composition or a property correlation.

What Gas Volume Factor Means

Gas volume changes substantially as pressure and temperature change. At high reservoir pressure, a fixed amount of gas generally occupies less space than it would at low standard pressure. Heating tends to increase its volume, while compression tends to reduce it. Bg captures the combined effect relative to a clearly defined reference state.

In petroleum calculations, Bg is often reported in reservoir barrels per standard cubic foot, reservoir cubic feet per standard cubic foot, or reservoir cubic metres per standard cubic metre. The unit labels matter: the factor is a volume ratio, not a gas density, total gas volume, or pressure. For example, multiplying a standard gas volume by Bg estimates the corresponding reservoir volume when units and reference conditions match.

The phrase “gas volume factor” can also be used loosely in other contexts. This page uses the petroleum-engineering meaning, not a generic gas-law volume conversion independent of reference conditions.

How to Use the Calculator

Enter reservoir pressure and temperature, then provide Z for the gas at those reservoir conditions. Enter the standard pressure and temperature used by your measurement or engineering convention. The output is meaningful only if the standard conditions are the same ones used for the standard gas volume in the calculation.

  • Use absolute pressure. Convert gauge pressure by adding the local atmospheric pressure before entering it; do not enter a gauge value as if it were absolute.
  • Use a Z value appropriate to the gas mixture, pressure, and temperature. If Z is unknown, obtain it from an appropriate equation of state, correlation, or property source.
  • Check whether a document defines standard conditions at 0 °C, 15 °C, 15.56 °C, or another temperature. Different conventions produce different factors.
  • Keep the same volume basis when applying the result, such as standard cubic metres or standard cubic feet.

The calculator accepts nonnegative pressures and Z values, but zero pressure cannot represent a physical state for this ratio and should not be used. In practice, enter positive absolute pressures and a physically appropriate positive Z factor.

Reference Conditions and Comparisons

There is no single standard temperature used everywhere. Gas measurement standards and engineering workflows may specify different reference temperatures and pressures. Because Bg divides reservoir volume by standard volume, changing the reference state changes the numerical result even when reservoir conditions are unchanged. Always quote the standard conditions alongside a reported factor.

Some sources express the same concept as a reciprocal: standard gas volume divided by reservoir gas volume. That is not Bg as defined here. A quick check is that under high pressure the reservoir volume is usually smaller, so reservoir volume per standard volume is commonly much less than 1. A reciprocal would commonly be greater than 1.

Limits and Common Mistakes

The equation is a useful state conversion, but it does not calculate the total gas in place or predict how much gas a reservoir can produce. Those tasks require additional information, such as pore volume, saturation, composition, production history, and reservoir behavior. Nor does the calculator establish a reliable Z factor: gas composition and conditions can make non-ideality important.

  • Gauge versus absolute pressure: the gas law requires absolute pressure. Using gauge pressure can cause a large error, especially at low pressures.
  • Temperature units: ratios must use absolute temperature. Dividing Celsius temperatures directly is incorrect.
  • Mixing standard bases: a factor based on one standard temperature should not be applied to a volume quoted at another without conversion.
  • Assuming Z = 1: this is the ideal-gas approximation, not a universal property of real natural gas.
  • Rounding too early: keep adequate precision for Z and intermediate values, then round the final result to match the quality of the input data.

For demanding engineering work, verify the factor with the governing measurement standard, a validated gas-property method, and the project’s specified equation of state. The calculator is for study and planning arithmetic; it is not a substitute for a reservoir model or an engineering review.

Frequently Asked Questions

What is the gas formation volume factor?
Bg is reservoir gas volume divided by the volume of the same amount of gas at specified standard conditions.

Can gas volume factor be greater than 1?
Yes, depending on the relative pressure and temperature conditions. It is often below 1 for high-pressure reservoirs compared with low-pressure standard conditions, but that is not a rule for every state or reference basis.

Why does the calculator need Z?
Z corrects the ideal-gas relationship for real-gas behavior. Its value depends on the gas and its pressure and temperature, so it should come from a suitable property calculation or source.

Is standard temperature always 15.56 °C?
No. Standard conditions depend on the applicable convention. The calculator uses 15.56 °C as a default; change it to the reference temperature required by your data.

Is gas volume factor the same as gas compressibility factor?
No. Z is a dimensionless correction in the real-gas equation of state. Bg is a ratio of gas volumes at reservoir and standard conditions and uses Z as one of its inputs.

Related

Formula used
in p | Reservoir pressure | kPa absolute | 10000 | 0
in t | Reservoir temperature | °C | 80 | -273.15
in z | Gas deviation factor Z | - | 0.9 | 0
in ps | Standard pressure | kPa absolute | 101.325 | 0
in ts | Standard temperature | °C | 15.56 | -273.15
out bg | Gas formation volume factor | m³/standard m³ | (z * (t + 273.15) / p) / ((ts + 273.15) / ps) | 4
out rbscf | Gas formation volume factor | reservoir ft³/standard ft³ | bg | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →