molecalculator

Moles & Molar Mass

Ge Electron Configuration Long Form (Full Version)

Calculator No. 01-9643 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The long-form (full) electron configuration of germanium (Ge, atomic number 32) is 1s2 2s2 2p6 3s2 3p6 3d10 4s2 4p2. This notation lists every occupied subshell in order of increasing principal quantum number (n) and azimuthal quantum number (l), showing that germanium has 32 electrons distributed across four shells.

What the Long Form Actually Shows

The long-form configuration spells out each subshell explicitly, rather than using the shorthand noble-gas notation. For germanium, the noble-gas shorthand is [Ar] 3d10 4s2 4p2, where [Ar] represents the 18 electrons of argon (1s2 2s2 2p6 3s2 3p6). The long form simply expands that core. Each superscript is the number of electrons in that subshell, and the sum of all superscripts must equal the atomic number (32 for Ge).

How the Subshells Fill (Aufbau Principle)

Electrons occupy orbitals in order of increasing energy, following the Aufbau principle. The filling order for germanium is:

  • 1s (2 electrons)
  • 2s (2 electrons)
  • 2p (6 electrons)
  • 3s (2 electrons)
  • 3p (6 electrons)
  • 4s (2 electrons) — fills before 3d because 4s is lower in energy
  • 3d (10 electrons)
  • 4p (2 electrons)

The 4s subshell fills before 3d, which is why the order in the long form is 3d10 4s2 4p2, not 4s2 3d10 4p2 in the written notation (though both are seen; the Aufbau order is 4s before 3d, but the standard written order lists subshells by principal quantum number).

Why Germanium Has 4 Valence Electrons

The outermost shell (n=4) contains 4s2 4p2, giving germanium four valence electrons. This places Ge in group 14 of the periodic table, alongside carbon, silicon, tin, and lead. These four electrons explain germanium’s semiconductor behavior: it can form four covalent bonds (as in GeO2 or in its diamond cubic crystal structure), and its electrical conductivity lies between that of metals and insulators. The 3d10 electrons are core electrons, not involved in bonding.

Common Mistakes and Misconceptions

A frequent error is writing 3d10 before 4s2 in the long form, which is technically the Aufbau order but not the standard written order. Another mistake is miscounting: 2+2+6+2+6+10+2+2 = 32, so if your configuration doesn’t sum to 32, you’ve made an error. Some students also confuse germanium with gallium (Z=31, which has 4p1) or arsenic (Z=33, which has 4p3). Finally, the 3d subshell holds 10 electrons, not 8 — the d subshell has five orbitals, each holding two electrons.

How to Derive It from the Periodic Table

You can read the long-form configuration directly from the periodic table without memorizing it:

  1. Start at hydrogen (Z=1) and move across each period, adding electrons to the subshell indicated by the block (s-block, p-block, d-block, f-block).
  2. Period 1: 1s2 (He)
  3. Period 2: 2s2 2p6 (Ne)
  4. Period 3: 3s2 3p6 (Ar)
  5. Period 4: 4s2 (Ca), then 3d10 (Zn), then 4p2 (Ge)

Counting through the fourth period: K (4s1), Ca (4s2), Sc through Zn (3d1 through 3d10), then Ga (4p1), Ge (4p2).

Related Configurations: Ions and Excited States

Germanium commonly forms Ge2+ and Ge4+ ions. For Ge2+, remove the two 4p electrons: 1s2 2s2 2p6 3s2 3p6 3d10 4s2. For Ge4+, remove the 4s2 as well, leaving [Ar] 3d10. In excited states, an electron from 4s can be promoted to 4p or 5s, but the ground state is always the one listed above. The condensed form [Ar] 3d10 4s2 4p2 is preferred in most textbooks because it’s shorter, but the long form is needed when you’re explicitly counting all electrons or working with X-ray spectroscopy.

Frequently Asked Questions

What is the shorthand electron configuration for Ge?
The shorthand is [Ar] 3d10 4s2 4p2. The [Ar] core represents the 18 electrons of argon, and the remaining 14 electrons are written explicitly.

Why is it 3d10 4s2 and not 4s2 3d10?
Both orders appear in textbooks. The Aufbau filling order puts 4s before 3d because 4s is lower in energy. However, the standard written order lists subshells by principal quantum number (3d before 4s). Either is acceptable as long as the electron count is correct.

How many unpaired electrons does germanium have?
In the ground state, germanium has two unpaired electrons: one in each of the two 4p orbitals. The 4s electrons are paired, and all 3d electrons are paired.

Is germanium a metal or nonmetal?
Germanium is a metalloid. Its electron configuration (four valence electrons) gives it intermediate properties: it looks metallic but has semiconductor behavior, with a band gap of about 0.67 eV at room temperature.

What is the electron configuration of Ge4+?
Ge4+ has lost the 4s2 and 4p2 electrons, so its configuration is [Ar] 3d10 or fully: 1s2 2s2 2p6 3s2 3p6 3d10.

Why does the 4s fill before 3d?
For neutral atoms, the 4s orbital has a lower energy than 3d because of electron-electron repulsion and penetration effects. This is why potassium (Z=19) and calcium (Z=20) have 4s1 and 4s2, respectively, before any 3d electrons appear.

Related

Formula used
in z | Atomic number Z | - | 32 | 1 | 118
out cf | Long-form configuration | - | cf | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →