molecalculator

Moles & Molar Mass

Absorbance vs. Concentration Graph: Beer–Lambert Law

Calculator No. 01-5447 · Updated · Formula and assumptions shown below

Absorbance 1.0000 AU
Concentration
0.0001 mol/L
Set in the form below
Molar absorptivity
10000 L/(mol·cm)
Set in the form below
Path length
1 cm
Set in the form below
You enter
Concentration (mol/L), Molar absorptivity (L/(mol·cm)), Path length (cm)
You get
Absorbance (AU)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A graph of absorbance against concentration is usually a straight line: concentration goes on the x-axis and absorbance on the y-axis. In the Beer–Lambert law, absorbance is proportional to concentration when path length, wavelength, and measurement conditions are held constant; this calculator predicts absorbance from those values.

Formula

The Beer–Lambert law is A = εlc. Here, A is absorbance, conventionally reported as a dimensionless value (often labeled absorbance units, AU); ε is molar absorptivity in L/(mol·cm) at the specified wavelength and conditions; l is the optical path length in cm; and c is concentration in mol/L. With ε and l fixed, the graph of A against c has slope εl and ideally has an intercept of zero.

The equation uses molar concentration and path length in the units paired with the chosen molar absorptivity. If a value of ε is specified in different units, convert the inputs or use a matching form of the law rather than mixing unit systems. The calculator treats ε as a nonnegative input; its default is an illustrative value, not a universal property of a substance.

Worked Example

Using the calculator’s default values—c = 0.0001 mol/L, ε = 10,000 L/(mol·cm), and l = 1 cm:

  1. Calculate the slope for the fixed path length: εl = (10,000 L/(mol·cm))(1 cm) = 10,000 L/mol.
  2. Multiply by concentration: A = (10,000 L/mol)(0.0001 mol/L) = 1.

The predicted absorbance is 1.0000 AU to four decimal places. In an ideal graph with these conditions, each concentration increase of 0.0001 mol/L raises absorbance by 1.0000.

Assumptions

  • The absorbing species follows the Beer–Lambert relationship over the concentration range being considered.
  • Wavelength, path length, solvent, temperature, and relevant chemical conditions are fixed.
  • The sample is sufficiently clear and dilute for the chosen calibration range; scattering, chemical changes, and stray light are negligible.
  • The molar absorptivity is appropriate for the substance, wavelength, and conditions. Its default is only an example.

What the Graph Shows

Absorbance measures how much light is attenuated by a sample. It is calculated from the ratio of incident light intensity to transmitted intensity: A = log10(I0/I), where I0 is the incident intensity and I is the transmitted intensity. Because absorbance is logarithmic, it is not the same as the percentage of light absorbed. For example, A = 1 corresponds to a transmittance of 10%, since I/I0 = 10−1; the absorbed fraction is then 90% if reflection and scattering are ignored.

On a conventional calibration plot, the horizontal axis is concentration and the vertical axis is measured absorbance. If the data follow the law, higher concentrations give higher absorbance and the points lie near a straight line. The gradient represents εl, not ε alone unless the path length is 1 cm. A nonzero intercept can arise from blank offset or instrument background; it should be investigated rather than automatically treated as a chemical effect.

To use such a graph to find an unknown concentration, measure the sample’s absorbance under the same conditions, then read the corresponding concentration from the calibration line. If the fitted line is A = mc + b, solve c = (A − b)/m. The calculator instead predicts absorbance from a concentration and given ε and path length; it does not fit experimental data or determine an unknown from a measured reading.

How to Build and Use a Calibration Plot

A calibration curve is made from standards with known concentrations. Measure their absorbances using the same wavelength and optical setup planned for the unknown, and plot the paired readings. A blank helps account for absorbance from the solvent, container, and other background contributions. Apply blank correction consistently: either subtract the blank from every reading or use a documented calibration procedure that accounts for it.

  1. Choose a wavelength where the analyte absorbs and where readings are useful across the expected range.
  2. Prepare several standards spanning the unknown’s likely concentration. Include a blank and avoid extrapolating far beyond the standards.
  3. Measure standards and unknowns under matching conditions, recording replicates when appropriate.
  4. Plot concentration on x and absorbance on y, then inspect the points and residuals as well as the fitted line.
  5. Use the fitted relationship to calculate the unknown, and dilute and remeasure it if its reading falls outside the validated range.

A straight-line fit is appropriate only over a range where the relationship is sufficiently linear. Do not force the intercept to zero simply because the ideal equation predicts zero absorbance at zero concentration; a forced fit can conceal blank or baseline errors. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Why a Graph May Curve or Shift

Real measurements can depart from the ideal line. At high concentration, molecular interactions or changes in chemical form can alter absorptivity. Scattered light, a dirty or mismatched cuvette, bubbles, fingerprints, an incorrect blank, or an unstable light source can also distort readings. A change in wavelength or path length changes the relationship too, so calibration standards and unknowns must be measured consistently.

Check whether the standards themselves were prepared accurately and mixed evenly. If the unknown is more concentrated than the calibration range, dilution followed by a new measurement is generally more reliable than extrapolation. A dilution changes the concentration being measured: multiply the measured diluted-sample concentration by the dilution factor to recover the original concentration, keeping all volume units consistent.

Frequently Asked Questions

What is the slope of absorbance against concentration?
For a Beer–Lambert plot with concentration on the x-axis, the ideal slope is εl. Its numerical units depend on the concentration and path-length units used; with mol/L and cm, it is commonly expressed in L/mol.

Which variable goes on each axis?
For the usual calibration graph, put concentration on the x-axis and absorbance on the y-axis. The graph’s slope then shows how much absorbance changes per unit concentration.

Should the line pass through zero?
The ideal Beer–Lambert equation predicts zero absorbance at zero analyte concentration after appropriate blank correction. Experimental data may have a nonzero intercept because of background, blanking, or measurement offsets.

Is absorbance the same as percent light absorbed?
No. Absorbance is logarithmic. If transmittance is expressed as a fraction T, A = −log10(T); the absorbed percentage is not simply 100 times the absorbance.

Can I use the straight line at any concentration?
No. Linearity is limited to the validated range for the substance and measurement conditions. Use standards to establish that range, and dilute samples outside it rather than assuming the line continues indefinitely.

Related

Formula used
in c | Concentration | mol/L | 0.0001 | 0
in ep | Molar absorptivity | L/(mol·cm) | 10000 | 0
in l | Path length | cm | 1 | 0
out a | Absorbance | AU | ep * l * c | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →