molecalculator

Moles & Molar Mass

Half Life Quiver: What It Is & How to Use It

Calculator No. 01-8387 · Updated · Formula and assumptions shown below

Minimum tube depth 35.0 cm
Arrows that fit
13
Result, rounded to a whole number
Arrow length
70 cm
Set in the form below
Arrow diameter
8.8 mm
Set in the form below
You enter
Arrow length (cm), Arrow diameter (mm), Number of arrows, Quiver tube depth (cm)
You get
Minimum tube depth (cm), Arrows that fit
Rounding
1 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The “Half Life Quiver” is a specialized quiver designed to hold half-length arrows, commonly used in traditional archery and mounted archery. You enter your arrow length and diameter, and the calculator below determines the minimum quiver tube depth and the number of arrows that fit, helping you choose or build a quiver that securely holds your arrows without rattling or falling out.

Formula

The calculator uses two simple relationships. First, the minimum quiver tube depth is half the arrow length: Minimum depth = Arrow length × 0.5. This ensures the arrow’s center of gravity sits inside the tube, keeping it stable. Second, the number of arrows that fit across a tube’s diameter is: Arrows that fit = floor(Quiver tube depth / (Arrow diameter + 2 mm)), where the 2 mm accounts for the arrow’s fletching clearance and spacing. In words: measure your arrow from nock groove to tip, divide by two for the minimum tube depth; for capacity, divide the tube’s inside depth by the arrow diameter plus 2 mm and round down.

Worked Example

Using the defaults: arrow length = 70 cm, arrow diameter = 8.8 mm, number of arrows = 5, quiver tube depth = 40 cm.

  • Minimum tube depth = 70 cm × 0.5 = 35.0 cm
  • Arrows that fit = floor(40 cm / (8.8 mm / 10 + 2 mm)) = floor(40 / (0.88 + 0.2)) = floor(40 / 1.08) = floor(37.04) = 37 arrows

So a 40 cm deep tube holds up to 37 half-arrows of this diameter, but the minimum depth for a 70 cm arrow is 35 cm. The calculator’s first output shows 35.0 cm, and the second shows 37.

Assumptions

  • Arrow length is measured from the nock groove to the tip (not including the point).
  • The 2 mm clearance is a general fletching clearance; larger fletching may need more.
  • Tube depth is the inside usable depth, not the outside height.
  • Arrows are assumed to be parallel and not bundled with a spacer.

What Is a Half Life Quiver?

A half life quiver (often just called a “half quiver”) is a quiver designed for arrows that are cut shorter than full-length. In traditional archery, full-length arrows are typically 28 to 32 inches (71–81 cm). Half arrows are about half that length, usually 14–18 inches (36–46 cm), and are used in mounted archery (horseback archery) or for short-draw bows. The quiver itself is a narrow tube or pocket worn on the hip, back, or saddle, sized so that the arrow’s center of gravity is inside the tube, preventing the arrow from tipping or falling out during movement.

How It Works: Why Half Length?

The name “half life” comes from the arrows being half the length of standard arrows, not from radioactive decay. The quiver works by holding the arrow at its balance point. For a typical arrow, the balance point is around 10–15% forward of center, but for a half arrow, the center is roughly at 50% of the length. By making the tube at least half the arrow length, the arrow’s center of mass is inside the tube, so the arrow stays put even when the quiver is jostled. The tube’s diameter also matters: it must be wide enough to clear the fletching (feathers or vanes) but narrow enough to grip the shaft lightly. Most half quivers use a foam insert or a leather strap to hold the arrows in place.

How to Choose a Half Life Quiver

Choosing the right half quiver depends on three measurements:

  • Arrow length: Measure your actual arrow, not the bow’s draw length. Use the calculator above to find the minimum tube depth.
  • Arrow diameter: Most carbon arrows are 6–9 mm; aluminum arrows are 5–8 mm. The tube must clear the fletching, which adds about 2–3 mm.
  • Number of arrows: Mounted archers typically carry 3–7 arrows. The tube’s inside depth (not height) determines how many fit side by side.

For example, a 16-inch (40.6 cm) half arrow with 8.8 mm diameter needs a tube at least 8 inches (20.3 cm) deep. A 3-inch (7.6 cm) inside diameter tube can hold about 6 arrows if spaced 1 cm apart. Always check the inside diameter, not the outside, because thick leather or plastic walls reduce usable space.

Common Problems and Misconceptions

A frequent mistake is buying a quiver that is too shallow. If the tube is less than half the arrow length, the arrow’s tip becomes top-heavy and the arrow flops out. Another issue is fletching clearance: arrows with large feathers (e.g., 5-inch shield cut) need a wider tube than arrows with small vanes. A third misconception is that “half life” refers to the quiver’s durability or a brand name—it does not; it simply describes the arrow length. Also, some archers think a deeper tube is always better, but an overly deep tube makes arrows hard to grip and draw quickly, which defeats the purpose in mounted archery.

Costs and Materials

Half quivers range from about $30 for a simple nylon tube to $150 for a custom leather back quiver. Materials affect price and function: leather is durable and traditional but heavier; nylon is light and water-resistant; carbon fiber tubes are stiff and very light but expensive. For mounted archery, a hip or saddle quiver with a secure strap is essential. The calculator above helps you avoid buying a quiver that is too small or too large, saving you from a wasted purchase.

Alternatives to a Half Life Quiver

If a half quiver doesn’t suit you, consider these alternatives:

  • Full-length quiver: Holds standard arrows, but is longer and heavier.
  • Side quiver (hip quiver): Attaches to the belt, holds arrows at an angle; works with half arrows if the tube is deep enough.
  • Back quiver: Carries arrows on the back; half arrows may rattle unless padded.
  • Bow quiver: Mounts directly on the bow; only practical for a few arrows.
  • DIY tube quiver: A PVC pipe or carbon tube with a foam base; cheap and customizable.

Each has trade-offs in speed, comfort, and arrow retention. The half quiver is best when you need quick access and minimal bulk.

Frequently Asked Questions

What is a half life quiver used for? It’s used to carry half-length arrows, mainly in mounted archery or for short-draw bows, where full-length arrows are impractical.

How do I measure arrow length for a half quiver? Measure from the nock groove (where the string sits) to the tip of the shaft, not including the arrowhead. Use that number in the calculator.

Can I use a full-length quiver for half arrows? Yes, but the arrows will rattle and may fall out because the tube is too deep relative to the arrow’s center of gravity. You can add a foam spacer at the bottom.

What if my arrows have large fletching? Increase the clearance in the calculator (use 3–4 mm instead of 2 mm) or choose a quiver with a wider inside diameter.

Does the quiver need to be exactly half the arrow length? No, half is the minimum. A bit deeper (60% of arrow length) is fine, but too deep makes arrows hard to grab.

Are half arrows weaker than full arrows? Not necessarily. Stiffness depends on spine, not length. A half arrow cut from a full shaft is stiffer than the original, so you may need a weaker spine shaft.

Related

Formula used
in m | Arrow length | cm | 70 | 0
in d | Arrow diameter | mm | 8.8 | 0
in n | Number of arrows | - | 5 | 1
in h | Quiver tube depth | cm | 40 | 0
out req | Minimum tube depth | cm | m * 0.5 | 1
out fit | Arrows that fit | - | floor(h / (d / 10 + 2)) | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →