molecalculator

Moles & Molar Mass

How to Calculate Injection Pressure

Calculator No. 01-11926 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator determines the injection pressure required to fill a mold cavity during plastic injection molding. You enter the melt viscosity, flow rate, and mold geometry, and it returns the pressure drop (in MPa or psi) needed to push the polymer through the sprue, runners, and gate. The calculation uses the Hagen–Poiseuille equation for a circular channel, which is the standard first-order approximation for injection molding pressure drop.

Formula

The injection pressure (ΔP) is calculated using the Hagen–Poiseuille equation for laminar flow through a circular tube:

ΔP = (8 · η · Q · L) / (π · r⁴)

Where:

  • ΔP = pressure drop (Pa, converted to MPa or psi)
  • η = melt viscosity (Pa·s)
  • Q = volumetric flow rate (m³/s, converted from cm³/s)
  • L = total flow length (m, converted from mm)
  • r = effective channel radius (m, converted from mm)

Note: The calculator converts all inputs to SI units before applying the formula. The result is the pressure drop in the delivery system (sprue, runner, gate) and assumes a single circular channel. For non-circular cross-sections, you must use an equivalent hydraulic radius (r = 2·A/P, where A is cross-sectional area and P is wetted perimeter).

Worked Example

Using the default values from the calculator:

  • Viscosity (η) = 250 Pa·s
  • Flow rate (Q) = 50 cm³/s = 50 × 10⁻⁶ m³/s
  • Flow length (L) = 100 mm = 0.1 m
  • Channel radius (r) = 2.5 mm = 0.0025 m

Plug into the formula:

ΔP = (8 × 250 × 50×10⁻⁶ × 0.1) / (π × (0.0025)⁴)

First, compute the denominator: (0.0025)⁴ = 3.90625 × 10⁻¹¹ m⁴. Multiply by π: 1.22718 × 10⁻¹⁰ m⁴.

Numerator: 8 × 250 = 2000; 2000 × 50×10⁻⁶ = 0.1; 0.1 × 0.1 = 0.01. So ΔP = 0.01 / 1.22718×10⁻¹⁰ = 8.148 × 10⁷ Pa.

Convert to MPa: 8.148 × 10⁷ Pa / 10⁶ = 81.48 MPa. The calculator shows 81.48 MPa (rounded to 2 decimals). In psi: 81.48 × 145.0377 = 11,818 psi.

Assumptions

  • Steady, laminar, incompressible Newtonian flow (constant viscosity).
  • Flow through a single circular channel of constant radius.
  • No frictional losses at bends or contractions (these add extra pressure drop).
  • Melt temperature is uniform; viscosity is constant along the flow path.
  • Ignore the pressure drop in the mold cavity itself; this calculator covers the delivery system only.

When to Use This Calculation

Injection pressure is a key process parameter in plastic injection molding. It must be high enough to fill the mold completely but not so high that it causes flashing, part sticking, or excessive residual stress. This calculation gives a first estimate for the pressure needed in the sprue/runner/gate system, which is typically 30–70% of the total injection pressure (the rest goes to filling the cavity). Use it during mold design to check whether your machine’s maximum injection pressure is sufficient, or to troubleshoot short shots (incomplete filling).

How to Read the Result

The result is the pressure drop (ΔP) from the nozzle to the gate. The actual injection pressure set on the machine is the sum of this drop plus the cavity pressure. If the calculated value exceeds your machine’s maximum, you need to reduce viscosity (increase melt temperature), lower flow rate, shorten flow length, or increase channel radius (since pressure scales with 1/r⁴, a small radius increase has a huge effect). The psi value is useful when comparing with machine specifications that use imperial units.

Common Mistakes

  • Unit mix-ups: Using mm directly in the radius without converting to meters. Always convert to SI before calculating.
  • Using diameter instead of radius: The formula requires radius (r). If you have a diameter, divide by 2 first.
  • Ignoring non-circular channels: Real runners are often trapezoidal or semicircular. Using the actual radius of a circular equivalent is essential; otherwise, the pressure is underestimated.
  • Assuming constant viscosity: Real polymer melts are shear-thinning; viscosity drops with shear rate. Using a high-shear viscosity gives a more realistic estimate.
  • Forgetting the cavity pressure: The result is only the delivery system drop. Add the cavity pressure (often 20–50 MPa for thin parts) to get total injection pressure.

Tips

  • Use a viscosity value measured at the actual melt temperature and shear rate (from a capillary rheometer or supplier data).
  • For a multi-cavity mold, divide the total flow rate by the number of cavities for each branch, but sum the pressure drops along the path.
  • If your runner system has multiple segments (sprue, runner, gate), calculate the pressure drop for each segment separately and add them, using the appropriate radius and length for each.
  • For a quick safety margin, multiply the calculated pressure by 1.2–1.5 to account for bends, contractions, and non-Newtonian effects.
  • Use the equivalent hydraulic radius for non-circular cross-sections: r_eq = 2A/P. For a rectangle of width w and height h, A = w·h, P = 2(w+h), so r_eq = w·h/(w+h).

Troubleshooting

If the calculated pressure seems too high: Check your viscosity value. If you used a zero-shear viscosity, the estimate will be high. Use a viscosity at a typical shear rate (e.g., 1000 s⁻¹). Also verify the flow rate – it might be higher than needed.

If the result is too low: You might have used a diameter instead of radius, or forgotten to convert units. Re-check all inputs.

If the calculator shows “Cannot compute”: This happens if any input is zero or negative. Ensure all values are positive.

If your mold has a complex runner system: Break it into segments and calculate each separately, then sum. For a branched system, the pressure drop is the same across each branch (parallel flow), so use the branch with the highest resistance.

If the actual injection pressure differs from your calculation: Real molds have additional losses from gate geometry, cavity filling, and non-Newtonian effects. Use the calculated value as a starting point and adjust based on trial shots.

Frequently Asked Questions

What is a typical injection pressure for plastic parts?

Typical injection pressures range from 30 to 150 MPa (about 4,000–22,000 psi). Thin-wall parts or high-viscosity materials (like PC) require higher pressures, while thick parts or low-viscosity materials (like PE) need less.

How does melt temperature affect injection pressure?

Increasing melt temperature reduces viscosity, which lowers the pressure drop. However, too high a temperature can degrade the polymer, so there is an optimal range.

Can I use this calculator for any plastic material?

Yes, as long as you input the correct viscosity for your material at your processing conditions. The formula assumes Newtonian flow, so for shear-thinning materials, use an apparent viscosity at the expected shear rate.

What is the difference between injection pressure and holding pressure?

Injection pressure is used to fill the mold cavity, while holding pressure is applied after filling to pack more material and compensate for shrinkage. This calculator estimates the injection (fill) pressure only.

Why does the radius have such a big effect?

Because pressure drop is inversely proportional to the fourth power of radius (r⁴). Doubling the radius reduces the pressure drop by a factor of 16. This is why even small changes in runner diameter have a large impact.

Should I add a safety factor to the calculated pressure?

Yes, it is wise to add a 20–50% safety factor to account for real-world effects like bends, contractions, and non-Newtonian behavior. Also ensure your machine’s maximum pressure is above the calculated value.

Related

Formula used
in v | Melt viscosity | Pa·s | 250 | 0.001
in q | Volumetric flow rate | cm³/s | 50 | 0.001
in L | Flow length (sprue+runner+gate) | mm | 100 | 0.001
in r | Channel radius (equivalent) | mm | 2.5 | 0.001
out p | Injection pressure (pressure drop) | MPa | (8 * v * q / (pi * (r/1000)^4)) * (L/1000) / 1e6 | 2
out psi | Pressure in psi | psi | p * 145.0377 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →