This calculator works out the final molarity when you dissolve a measured mass of solute to a chosen final volume. Enter the solute mass, its molar mass, and the final solution volume to get molarity and millimolar concentration. It is for general study and lab-planning arithmetic, not for preparing anything for use in people or animals.
Formula
Molarity is the amount of solute in moles divided by the final solution volume in liters:
c = (m / M) / (V / 1000)
- c is molarity in mol/L.
- m is solute mass in grams.
- M is molar mass in grams per mole.
- V is final solution volume in milliliters; dividing by 1000 converts mL to L.
Millimolar concentration is cmM = c × 1000, because 1 mol/L equals 1000 mM. This calculator assumes the entered mass is pure solute and the measured volume is the final volume of the solution.
Worked Example
Using the calculator defaults: 2.922 g of solute, molar mass 58.44 g/mol, and a final volume of 250 mL.
- Convert mass to amount: 2.922 g / 58.44 g/mol = 0.050000 mol.
- Convert final volume: 250 mL / 1000 = 0.250 L.
- Calculate molarity: 0.050000 mol / 0.250 L = 0.2000 mol/L.
- Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM.
The calculator displays 0.2000 mol/L and 200.00 mM.
Assumptions
- The solute is pure, and its molar mass is appropriate for the chemical form being used.
- The stated volume is the final solution volume, not the volume of solvent added.
- The calculation describes amount concentration; it does not correct for reaction, dissociation, density, or temperature-dependent volume changes.
What changing concentration means
Concentration describes how much solute is present in a defined amount of solution. To lower concentration while keeping the amount of solute unchanged, add solvent and increase the final volume. To raise concentration, either add more solute or remove solvent. In a lab, the most straightforward controlled method is often dilution: transfer a known amount of a more concentrated solution and add solvent until the chosen final volume is reached.
Before starting, decide what concentration unit you need and whether the existing solution’s concentration is known. The calculator above is useful when preparing a solution from a solid with a known molar mass. For dilution from a stock solution, use the dilution equation below; it does not require the solute’s molar mass.
What You’ll Need
- A target concentration and final volume, with compatible units.
- For a solid-based calculation: solute mass, molar mass, and a balance suitable for that mass.
- For dilution: the stock concentration and the volume of stock to transfer.
- Suitable solvent, clean graduated glassware, a mixing vessel, and a label.
- Required personal protective equipment and the chemical’s safety data sheet (SDS).
Step-by-Step
- Choose the route. If starting with a solid, calculate the amount required using the calculator. If starting with a stock solution, calculate the stock volume using C1V1 = C2V2. This relationship assumes the solute amount is conserved during dilution.
- Make units consistent. In the dilution equation, concentrations must use the same units, and both volumes must use the same units. Rearrange it as V1 = C2V2/C1, where C1 is stock concentration, C2 is desired concentration, and V2 is desired final volume.
- Check feasibility. For dilution, the target concentration cannot exceed the stock concentration. Confirm the calculated transfer volume is measurable with the available equipment. If it is too small to measure reliably, use a suitable intermediate dilution under an approved lab method.
- Measure the solute or stock. For a solid, weigh the calculated mass. For a stock, measure the calculated aliquot. Avoid transferring material outside the intended vessel; rinse transfer surfaces into the vessel only when your method allows it.
- Add some solvent and dissolve or mix. Do not initially fill to the final mark. Mix until the solid has dissolved or the stock is evenly dispersed. Do not assume that the volume of solvent added equals the final solution volume.
- Set the final volume. Add solvent until the solution reaches the specified final volume using suitable graduated glassware. For accurate molarity, bring the solution to the mark at the temperature and by the procedure required by your method.
- Mix thoroughly and label. Close or cover the vessel as appropriate, mix until uniform, then label with identity, concentration, solvent, date, and any required hazard information. Follow your lab method, the safety data sheet (SDS), and your supervisor.
- Verify the result. Recheck calculations, units, and transfer volumes. If the concentration must be analytically confirmed, use an appropriate validated measurement rather than relying on arithmetic alone.
Common Mistakes
- Using solvent volume instead of final volume: dissolving a solute in 250 mL of solvent generally does not make 250 mL of solution. Bring the mixture to the intended final volume.
- Mixing units: using mL as though it were L changes the answer by a factor of 1000. Convert explicitly.
- Confusing mass concentration and molarity: g/L is not mol/L. Convert grams to moles using the correct molar mass.
- Using the wrong chemical form: hydrates, salts, and different protonation forms can have different molar masses. Use the value for the actual reagent.
- Rounding too early: keep extra digits through intermediate steps, then round the reported result to a precision justified by the measurements.
- Assuming dilution changes only volume: evaporation, reaction, precipitation, or adsorption can change the amount of dissolved solute and invalidate the simple dilution equation.
Tips
- Write units beside every value before calculating; cancel units to check that the result has the intended dimensions.
- Use the calculator’s final-volume field for the solution volume, not the amount of solvent.
- For dilution, calculate the transfer volume first, then add solvent to the target final volume rather than adding a calculated solvent volume blindly.
- Record the stock concentration and date if they affect the validity of the preparation.
- Use glassware and measurement methods appropriate to the accuracy needed; a mathematically precise answer cannot compensate for imprecise measurements.
Troubleshooting
The calculated dilution volume is larger than the final volume: check the units and equation. If the target concentration is above the stock concentration, dilution cannot achieve it; use a more concentrated stock or a different preparation route.
The solid will not dissolve: confirm the solvent and chemical form are correct, and consult the approved method. Do not change temperature, pH, or solvent without checking compatibility and safety requirements.
The final volume is overshot: adding more solute or evaporating solvent changes the preparation and may introduce errors. If accuracy matters, remake it or follow a validated correction procedure.
The result seems off by about 1000: check whether mL were converted to L and whether mol/L was confused with mM. Also verify that mass is in grams and molar mass in g/mol.
The solution looks uneven or contains particles: mix as directed and determine whether the material is fully soluble. A suspension is not necessarily a uniform solution, so do not treat it as the calculated molarity without an appropriate method.
Frequently Asked Questions
How do I decrease the concentration of a solution?
Add solvent while keeping the amount of solute unchanged, then make the mixture up to a larger final volume. For a known stock, calculate the aliquot with C1V1 = C2V2.
How can I increase concentration?
Add a measured amount of solute or remove solvent using an approved method. Recalculate the final concentration from the actual amount and final volume; evaporation may also affect stability or composition.
Does adding 100 mL of water to 100 mL of solution halve its concentration?
Not exactly in every case. The dilution equation uses the actual final volume, which may not equal the sum of the starting volumes. Measure or prepare to the desired final volume.
Can I use this calculator for g/L?
The calculator reports mol/L and mM. For mass concentration in g/L, divide solute mass in grams by final solution volume in liters; do not use molar mass in that calculation.
What if I do not know the stock concentration?
You cannot calculate a reliable dilution volume from an unknown concentration. Obtain a trustworthy concentration value or determine it using an appropriate analytical method before proceeding.
Does the calculator account for temperature?
No. It uses the entered final volume and does not correct for thermal expansion or other temperature effects. Follow the method’s specified temperature when precise concentration is needed.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s