molecalculator

Moles & Molar Mass

Combustion Analysis: Step-by-Step Guide

Guide 01-9977 · Updated · Step by step

Combustion analysis is a classic chemistry technique used to determine the empirical formula of a compound containing carbon, hydrogen, and sometimes other elements like oxygen, nitrogen, or sulfur. By burning a known mass of the sample and measuring the masses of CO2 and H2O produced, you can calculate the moles of carbon and hydrogen in the original sample, then find the empirical formula. This guide walks you through the entire process, from the setup to the final formula, with worked examples and common pitfalls.

What You’ll Need

  • A balanced combustion reaction (the compound + O2 → CO2 + H2O + possibly other products)
  • The mass of the original sample (in grams)
  • The mass of CO2 produced (in grams)
  • The mass of H2O produced (in grams)
  • Atomic masses: C = 12.011 g/mol, H = 1.008 g/mol, O = 15.999 g/mol (use exact values from your periodic table)
  • A calculator (or this page’s built-in calculator)
  • If the compound contains nitrogen, you also need the mass of N2 gas collected (or use a separate analysis)

Step-by-Step

  1. Write the combustion reaction. For a hydrocarbon (CxHy): CxHy + O2 → CO2 + H2O. For a compound with oxygen, the product is the same, but you’ll account for oxygen later.
  2. Convert the mass of CO2 to moles of CO2. Use the molar mass of CO2 (44.009 g/mol). Moles CO2 = mass CO2 / 44.009.
  3. Convert moles of CO2 to moles of carbon. Each mole of CO2 contains exactly 1 mole of carbon. So moles C = moles CO2.
  4. Convert the mass of H2O to moles of H2O. Molar mass of H2O = 18.015 g/mol. Moles H2O = mass H2O / 18.015.
  5. Convert moles of H2O to moles of hydrogen. Each mole of H2O contains 2 moles of hydrogen. Moles H = 2 × moles H2O.
  6. If the compound contains oxygen, find the mass of oxygen by subtraction. Mass O = (mass of original sample) − (mass C + mass H). Mass C = moles C × 12.011, mass H = moles H × 1.008. Then convert mass O to moles O: moles O = mass O / 15.999.
  7. If nitrogen is present, you’ll have a separate measurement. The mass of N2 gas (or a nitrogen balance) gives moles N. For example, if you collect 0.140 g of N2, moles N = 0.140 / 28.014 (molar mass N2) × 2 = 0.00999 mol N.
  8. Divide all mole values by the smallest number of moles. This gives the mole ratio of elements in the compound.
  9. If the ratios are not whole numbers, multiply by a common factor. For example, if you get C: 1.00, H: 1.50, O: 0.50, multiply by 2 to get C2H3O.
  10. Write the empirical formula. The whole-number ratios become the subscripts.
  11. If you have the molar mass of the compound, find the molecular formula. Divide the molar mass by the empirical formula mass (the sum of atomic masses in the empirical formula). Multiply all subscripts by that integer.

Common Mistakes

  • Forgetting the factor of 2 for hydrogen. Each water molecule has two hydrogen atoms, so moles H = 2 × moles H2O. This is the most frequent error.
  • Using the molar mass of CO2 as 44 g/mol instead of 44.009. For high precision, use the exact value (or at least 44.01).
  • Assuming oxygen is present without checking. If the masses of C + H add up to the sample mass, there is no oxygen. Only subtract oxygen if the sum is less than the sample mass.
  • Rounding too early. Keep at least 4 significant figures during intermediate steps. Round only at the end.
  • Using the empirical formula as the molecular formula. The empirical formula is the simplest ratio, not necessarily the actual molecule. You need the molar mass to get the molecular formula.
  • Ignoring nitrogen or sulfur. If the compound contains these, you must account for them; otherwise your mole ratios will be wrong.

Tips

  • Always write down the balanced equation first. It helps you see the stoichiometry.
  • Use a table to organize your data: mass, molar mass, moles, ratio.
  • Check that the total mass of elements (C + H + O) equals the original sample mass (within rounding error). This is a good sanity check.
  • If you get a ratio like 1.33, multiply by 3; if 1.25, multiply by 4; if 1.67, multiply by 6. These are common fractions.
  • When finding the molecular formula, the multiplier should be a whole number. If it’s not, you made an arithmetic error.
  • For practice, use known compounds (like glucose, C6H12O6) to verify your method.

Troubleshooting

  • Your mole ratios are not near whole numbers (e.g., 1.0, 2.0). First, check your arithmetic. If you have 1.5, 2.5, etc., multiply all ratios by 2. If you have 1.33, multiply by 3. If you have 1.25, multiply by 4. If you have something like 1.4, it’s likely an experimental error; recheck your measurements.
  • The mass of C + H exceeds the sample mass. This is impossible. You likely used the wrong molar mass for CO2 or H2O, or you misread the balance. Recalculate.
  • You get a negative mass for oxygen. That means your sample mass is less than the sum of C + H. This could be due to incomplete combustion or a calculation error. Check your data.
  • You don’t know if nitrogen is present. If the compound contains nitrogen, the combustion products will include N2 gas, which is often collected separately. If you don’t have that data, you cannot determine the formula correctly. You may have to assume no nitrogen if the problem doesn’t mention it.
  • Your empirical formula mass doesn’t divide the molar mass evenly. For example, if you get a molecular formula multiplier of 1.5, you likely made an error in the empirical formula. Recheck your mole ratios.

Frequently Asked Questions

What is the difference between empirical and molecular formula?

The empirical formula is the simplest whole-number ratio of atoms in a compound. The molecular formula shows the actual number of each atom in a molecule. For example, glucose has empirical formula CH2O and molecular formula C6H12O6. The molecular formula is always a whole-number multiple of the empirical formula.

How do I know if oxygen is in the compound?

If the sum of the masses of carbon and hydrogen (and any other known elements) is less than the original sample mass, the difference is oxygen. If the sum equals the sample mass, there is no oxygen. In combustion analysis, you don’t directly measure oxygen; you infer it by subtraction.

Can I use this method for compounds with nitrogen?

Yes, but you need to measure the nitrogen gas produced. The nitrogen is typically collected over water or in a separate trap. Then you convert the mass of N2 to moles of nitrogen atoms (remember 1 mole N2 = 2 moles N). Include that in your mole ratio.

What if the combustion is incomplete?

Incomplete combustion produces carbon monoxide (CO) or soot (C) instead of CO2. In a proper combustion analysis, the sample is burned in excess oxygen to ensure complete conversion. If you suspect incomplete combustion, your CO2 mass will be too low, and your empirical formula will be wrong. In practice, the analysis is done in a sealed apparatus with a catalyst to ensure complete combustion.

Why do I need the molar mass to get the molecular formula?

The empirical formula gives only the ratio of atoms, not the actual number. For example, both CH2O and C6H12O6 have the same empirical formula, but they are different compounds. The molar mass tells you how many empirical formula units are in one molecule (the multiplier). Without it, you can only report the empirical formula.

What are the units for the mole ratios?

Mole ratios are dimensionless. You divide each element’s moles by the smallest mole value, so the units cancel. The result is a set of numbers (like 1, 2, 3) that become the subscripts in the empirical formula.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →