molecalculator

Moles & Molar Mass

Find Concentration From Absorbance: Formula and Calculator

Calculator No. 01-5456 · Updated · Formula and assumptions shown below

Concentration 5.000 × 10−5 mol/L
Concentration
0.050 mmol/L
= Concentration × 1000
Blank-corrected absorbance
0.5
Set in the form below
Molar absorptivity
10000 L/(mol·cm)
Set in the form below
You enter
Blank-corrected absorbance, Molar absorptivity (L/(mol·cm)), Optical path length (cm)
You get
Concentration (mol/L), Concentration (mmol/L)
Rounding
6 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator estimates a solution’s molar concentration from its absorbance using the Beer–Lambert law. Enter the absorbance, the substance’s molar absorptivity at the measurement wavelength, and the optical path length; it returns concentration in mol/L and mol/mL. You need a suitable absorptivity value and a blank-corrected absorbance measured under matching conditions.

Formula

The Beer–Lambert law is A = εlc. Rearranged to find concentration: c = A / (εl).

  • A is blank-corrected absorbance, a dimensionless quantity.
  • ε is molar absorptivity at the selected wavelength, in L/(mol·cm).
  • l is the light path through the sample, in cm.
  • c is molar concentration, in mol/L.

The second calculator result converts mol/L to mmol/L by multiplying by 1,000; 1 mol/L equals 1,000 mmol/L. Absorptivity depends on the absorbing substance, wavelength, solvent, temperature, and chemical conditions. The default value is an example only, not a universal constant. Replace it with a validated value for your analyte and measurement conditions.

Worked Example

Using the calculator’s default inputs: A = 0.500, ε = 10,000 L/(mol·cm), and l = 1 cm.

  1. Calculate εl: 10,000 L/(mol·cm) × 1 cm = 10,000 L/mol.
  2. Divide absorbance by that product: c = 0.500 / 10,000 = 0.000050000 mol/L.
  3. Convert to millimolar: 0.000050000 mol/L × 1,000 = 0.050000 mmol/L.

Therefore, the calculated concentration is 0.000050 mol/L (shown to six decimal places by the calculator) and 0.050 mmol/L. The displayed precision is not a guarantee of measurement accuracy; report only the significant figures supported by your method.

Assumptions

  • The sample is sufficiently dilute for absorbance to be proportional to concentration over the range used.
  • The analyte’s absorptivity is known and applies to the sample’s wavelength and chemical conditions.
  • Absorbance has been corrected against an appropriate blank, and the measured path length is known.
  • The sample is homogeneous and does not scatter significant light or contain interfering absorbers.

What You’ll Need

  • An absorbance reading for the sample and a blank measured using the same relevant settings.
  • The molar absorptivity, ε, for the analyte at the measurement wavelength and applicable conditions, or a calibration curve made from standards.
  • The optical path length in centimetres. A standard cuvette commonly has a 1 cm path, but verify the actual path used.
  • A calculator or spreadsheet if you are not using this calculator.

For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. This calculation is for laboratory or study arithmetic, not for preparing anything for use in a person or animal.

Step-by-Step

  1. Identify the analyte and measurement conditions. Confirm which substance produces the measured signal, the wavelength used, and relevant solvent, pH, or other conditions. Molar absorptivity is not transferable automatically between wavelengths or chemical forms.
  2. Obtain an appropriate ε value. Use a value established for the same analyte and conditions, with units of L/(mol·cm). If it is not known reliably, do not guess: prepare suitable standards and determine concentration from a calibration curve instead.
  3. Measure and correct the absorbance. Use a blank containing the sample matrix without the absorbing analyte, as appropriate to your method. If the instrument reports sample absorbance and blank absorbance separately, calculate A = sample reading − blank reading. Enter the corrected value, not a transmittance percentage.
  4. Check the path length. Enter the distance the light travels through the sample in centimetres. If you use another unit, convert it first: 10 mm = 1 cm. Do not assume every measurement cell has a 1 cm path.
  5. Enter the three values. Type corrected absorbance, ε, and path length into the calculator. Absorbance has no unit; the ε and path-length units must match those stated in the fields.
  6. Read the concentration and check its scale. The first result is mol/L and the second is mmol/L. If useful, convert between units using 1 mol/L = 1,000 mmol/L, or 1 mmol/L = 1,000 µmol/L. Keep units attached to values in notes and reports.
  7. Check whether the method is valid at that concentration. Compare the absorbance with the instrument’s reliable range and the linear range established for the assay. If the reading is outside that range, dilute the sample using a documented method, measure again, and multiply the measured concentration by the total dilution factor.
  8. Record uncertainty and conditions. Note the wavelength, blank, path length, absorptivity source or calibration curve, dilution factor, and significant figures. These details make the calculated result interpretable and repeatable.

Common Mistakes

  • Using the wrong absorptivity. A value for another wavelength, solvent, or chemical form can produce a systematically wrong concentration. Check its source and units.
  • Mixing path-length units. The formula requires ε in L/(mol·cm) with l in cm. Entering millimetres as though they were centimetres changes the result by a factor of ten.
  • Using an uncorrected blank. Solvent, buffer, or container absorbance may be counted as analyte signal. Use the blank required by the method.
  • Confusing absorbance with transmittance. Do not enter a percentage of transmitted light as A. If only transmittance is available, convert it using A = −log10(T), where T is fractional transmittance (percentage divided by 100).
  • Assuming every sample follows a straight line. High absorbance, chemical interactions, scattering, or detector limits can invalidate the proportional relationship.
  • Rounding too early. Keep unrounded intermediate values and round the final reported value to a defensible number of significant figures.

Tips

  • Use the same wavelength, blank composition, and measurement setup for standards and unknown samples.
  • A calibration curve made from several known standards is often more dependable than a literature absorptivity, especially in a complex sample matrix.
  • Measure replicate samples when the method allows, and investigate inconsistent readings rather than averaging obvious outliers without a reason.
  • Check for bubbles, fingerprints, residue, or particles that can affect the light path or scatter light.
  • If a sample is diluted, track each dilution step and apply the combined dilution factor to the concentration calculated for the diluted sample.

Troubleshooting

The calculated concentration seems implausible: verify the absorbance, units, path length, ε source, and any dilution factor. Check whether the sample’s pH or solvent changes the analyte’s absorbing form.

The absorbance is negative or near zero: recheck blank selection, instrument zeroing, and whether the analyte absorbs at the chosen wavelength. A negative blank-corrected value usually means the signal is indistinguishable from background within the measurement uncertainty; it does not establish a negative physical concentration.

Replicates disagree: check sample mixing, bubbles, cell cleanliness and orientation, timing, and instrument stability. Repeat the blank and measurements according to the method.

The reading is outside the linear range: do not rely on direct extrapolation. Dilute the sample into the validated range, remeasure, and multiply by the dilution factor, or use a validated calibration method that covers the concentration.

No reliable ε value is available: use a calibration curve prepared from standards of known concentration under matching conditions. Fit the linear region and calculate the unknown from the curve; account for the curve’s intercept if the validated fit includes one.

Frequently Asked Questions

Can I find concentration from absorbance without molar absorptivity?
Not with the direct Beer–Lambert calculation. You need ε and path length, or a calibration curve relating absorbance to known concentrations.

What units should I use for concentration?
This calculator returns mol/L and mmol/L. Convert to another unit only after checking the conversion factor and keeping it consistent with your report.

Does absorbance have units?
No. Absorbance is dimensionless, although it is sometimes informally written as absorbance units.

What if my cuvette path length is not 1 cm?
Enter its actual path length in centimetres. The concentration calculation accounts for the path length through the εl term.

Can I use this for a mixture?
Only if the absorbing components and their contributions are appropriately resolved or modeled. Overlapping absorbers generally require a suitable multiwavelength method or calibration approach.

Why does a calibration curve give a different result?
The curve may capture matrix effects, instrument response, or a nonzero baseline that a single ε value does not. Confirm the standards, range, blank, and units, and use the validated method for the sample.

Related

Formula used
in a | Blank-corrected absorbance | - | 0.500 | 0
in eps | Molar absorptivity | L/(mol·cm) | 10000 | 0.001
in l | Optical path length | cm | 1 | 0.001
out c | Concentration | mol/L | a / (eps * l) | 6
out cm | Concentration | mmol/L | c * 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →