molecalculator

Moles & Molar Mass

Solution Concentration Calculator and How to Measure It

Calculator No. 01-5465 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Use this calculator to find a solution’s molarity from the solute mass, its molar mass, and the final solution volume. Enter those three values to get mol/L and mM; the guide below explains how to measure concentration and when this mass-based method applies.

Formula

Molarity is the amount of solute in moles divided by the final volume of solution in liters. First calculate moles as mass divided by molar mass, then convert milliliters to liters by dividing by 1000:

c = (m / mm) / (v / 1000)

  • c = molar concentration, in mol/L (also written M).
  • m = mass of solute, in grams (g).
  • mm = molar mass of the solute, in grams per mole (g/mol).
  • v = final solution volume, in milliliters (mL).

To express the result in millimolar, use cmM = c × 1000, because 1 mol/L equals 1000 mmol/L. The formula assumes the mass is the mass of the solute alone and that the volume entered is the total final volume of the solution.

Worked Example

For the default values, the solute mass is 2.922 g, its molar mass is 58.44 g/mol, and the final solution volume is 250 mL.

  1. Calculate the amount of solute: 2.922 g / 58.44 g/mol = 0.050000 mol.
  2. Convert the final volume: 250 mL / 1000 = 0.250 L.
  3. Divide moles by volume: 0.050000 mol / 0.250 L = 0.2000 mol/L.
  4. Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM.

The calculator reports 0.2000 mol/L and 200.00 mM.

Assumptions

  • The volume is the final solution volume, not the volume of solvent added.
  • The solute is treated as pure, and its stated molar mass is appropriate for the substance and chemical form used.
  • This is a mass-to-molarity calculation; it does not correct for impurities, chemical reaction, or changes in composition.
  • For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

What You’ll Need

  • The identity and chemical form of the solute, so you can use the correct molar mass.
  • A reliable mass for the solute and the final solution volume, with units.
  • A balance and suitable volumetric equipment if you are measuring a solution in a laboratory.
  • The substance’s purity or assay information if the calculation needs to account for less than 100% active material.

Step-by-Step

  1. Decide what concentration you need. Molarity is useful when calculations depend on moles per liter. Check whether your work instead specifies mass concentration, a percentage, or another measure; these are not interchangeable without additional information.
  2. Identify the exact solute. Find its formula and chemical form, including relevant hydration or salt form. Look up or calculate its molar mass in g/mol. For a compound, sum the atomic masses according to its formula; do not substitute the molar mass of a related form.
  3. Measure the solute mass. Use the mass of solute that actually goes into the solution, in grams. If purity is below 100%, a simple calculator result based on the weighed mass will overstate the concentration of the target substance unless the mass is corrected for the assay.
  4. Set the final volume. Determine the intended total solution volume. When a method requires volumetric preparation, dissolve the solute in less than the final volume first, then bring the solution to the specified final volume using the appropriate procedure. Adding a stated volume of solvent to the solute is not the same thing as making up to that final volume.
  5. Enter the values with the right units. Type mass in grams, molar mass in g/mol, and final volume in mL. Convert other units before entering them: for example, 1.00 g is 1000 mg, and 1.00 L is 1000 mL. The calculator converts mL to L in its formula.
  6. Read the molarity first. The headline result is mol/L. For example, 0.20 mol/L means 0.20 moles of the specified solute per liter of final solution, not per liter of solvent.
  7. Use the millimolar result when needed. The second result is the same concentration on a smaller unit scale. Since 1 mol/L = 1000 mM, 0.20 mol/L is 200 mM.
  8. Check the result against the method. Confirm the chosen concentration unit, substance form, mass, and final volume. For practical work, use the prescribed procedure and appropriate checks; calculation alone does not establish the true concentration of a prepared or unknown sample.

Common Mistakes

  • Using solvent volume instead of final volume: the denominator is the total volume of the finished solution. Solute can change the volume.
  • Mixing units: entering milligrams as grams or liters as milliliters creates an error by a factor of 1000. Convert first and label each value.
  • Choosing the wrong molar mass: hydrated salts, anhydrous compounds, and different ionic forms can have different molar masses.
  • Confusing molarity with mass concentration: g/L and mol/L describe concentration differently. To convert between them, the relevant molar mass is required.
  • Rounding too early: keep sensible precision through intermediate calculations, then round the displayed result to match the precision of the measurements.
  • Assuming ideal purity: an impure or degraded reagent can make the actual concentration lower than the calculation based on its total weighed mass.

Tips

  • Write each measurement beside its unit before calculating, and keep a record of the solute’s chemical form and molar mass source.
  • Use significant figures that reflect the least precise input. Extra calculator digits do not make an uncertain measurement more accurate.
  • For a target molarity, rearrange the same relationship to find the required solute mass: m = c × mm × (v / 1000), where volume is in mL.
  • If the solution is made by diluting a known stock, use a dilution relationship such as C1V1 = C2V2 rather than treating the added solvent volume as the final volume.
  • For an unknown sample, choose a validated analytical method suited to the substance. A mass-and-volume calculation only works when the solute amount and final solution volume are known.

Troubleshooting

  • The answer is about 1000 times too high or low: check whether you entered mg instead of g, or L instead of mL. The inputs require g and mL.
  • The result seems inconsistent with a known standard: verify the molar mass, chemical form, purity, and whether the volume is the final volume. Also check for transcription errors.
  • The solution did not reach the intended volume: the calculated molarity no longer matches the actual preparation. Measure or establish the final volume using the applicable lab method before relying on the value.
  • The substance will not dissolve or reacts during preparation: do not assume the nominal mass gives the intended concentration. Check the substance’s solubility and compatibility information and consult the approved method or supervisor.
  • You only have a measured sample response: this calculator cannot infer concentration from absorbance, titration, conductivity, or another instrument signal. Use the appropriate calibration, standardization, or analytical equation.

Frequently Asked Questions

What does molarity mean?
Molarity is the number of moles of solute per liter of final solution, expressed in mol/L.

Is molarity the same as concentration?
Molarity is one concentration unit. Concentration can also be expressed as g/L, percent, molality, or other measures, depending on the context.

Can I calculate concentration from mass and volume alone?
Not molarity: you also need the solute’s molar mass to convert its mass to moles. Mass concentration in g/L only needs mass and final volume.

Why must I use the final solution volume?
Molarity is moles divided by the volume of the complete solution. The volume after dissolving can differ from the solvent volume measured beforehand.

How do I convert mol/L to mM?
Multiply mol/L by 1000. For example, 0.015 mol/L equals 15 mM.

Can this calculator measure an unknown solution?
No. It calculates concentration from known solute mass, molar mass, and final volume. Unknown samples need a suitable measurement method and, often, calibration.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →