molecalculator

Moles & Molar Mass

Ideal Gas Specific Volume Calculator and Formula

Calculator No. 01-5694 · Updated · Formula and assumptions shown below

Ideal-gas specific volume 0.8497 m^3/kg
Ideal-gas density
1.1768 kg/m^3
= 1 ÷ Ideal-gas specific volume
Temperature
300 K
Set in the form below
Absolute pressure
101.325 kPa
Set in the form below
You enter
Temperature (K), Absolute pressure (kPa), Molar mass (g/mol)
You get
Ideal-gas specific volume (m^3/kg), Ideal-gas density (kg/m^3)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Ideal-gas specific volume is the volume occupied per unit mass of gas. This calculator finds it from the gas temperature and pressure, plus the gas’s molar mass; enter temperature in kelvins, pressure in kilopascals, and molar mass in grams per mole to get specific volume in cubic metres per kilogram.

Formula

For an ideal gas, specific volume is the gas constant per unit mass multiplied by absolute temperature and divided by absolute pressure:

v = RsT / P = RT / (MP)

  • v is specific volume in m3/kg.
  • Rs is the gas-specific constant in J/(kg·K).
  • T is absolute temperature in kelvins (K).
  • P is absolute pressure in pascals (Pa).
  • R is the universal gas constant, 8.31446261815324 J/(mol·K).
  • M is molar mass in kg/mol.

The calculator accepts pressure in kPa and molar mass in g/mol. The conversion factors cancel consistently: 1 kPa = 1,000 Pa and 1 g/mol = 0.001 kg/mol. Thus, using the entered units, the numerical form is v = 8.31446261815324 × T / (P × M), with the result in m3/kg. The second output is density, ρ = 1/v, in kg/m3.

Worked Example

Using the defaults—T = 300 K, P = 101.325 kPa, and M = 28.97 g/mol—the calculation is:

v = 8.31446261815324 × 300 / (101.325 × 28.97)

v = 2494.338785446 / 2935. ?

More precisely, 101.325 × 28.97 = 2935. ?; calculating the product gives 2935. ? and the quotient is approximately 0.8496 m3/kg.

With the displayed four decimal places, the specific volume is 0.8496 m3/kg. The corresponding density is 1 / 0.8496 ≈ 1.1769 kg/m3 (the calculator uses the unrounded specific volume for this output).

Assumptions

  • The gas is treated as ideal, so its compressibility factor is assumed to be 1.
  • Temperature is supplied in kelvins and pressure is absolute, not gauge pressure.
  • The entered molar mass represents the gas composition; for a mixture, use its appropriate mean molar mass.

What Specific Volume Means

Specific volume is an intensive property: it describes volume per unit mass rather than the total volume of a sample. Its SI unit, m3/kg, is the reciprocal of density. For example, a specific volume of 0.85 m3/kg means that one kilogram of the gas occupies about 0.85 cubic metres under the stated temperature and pressure, according to the model.

Specific volume is not the same as molar volume. Molar volume is volume per mole, commonly expressed in m3/mol or L/mol. To convert between them, divide molar volume by molar mass expressed in kg/mol. The ideal-gas molar volume is RT/P; dividing that by M gives the mass-specific formula used here.

How Temperature, Pressure, and Gas Type Affect It

At fixed pressure and gas composition, ideal-gas specific volume increases in direct proportion to absolute temperature. Heating a gas from 300 K to 600 K doubles its calculated specific volume if pressure remains unchanged. At fixed temperature and composition, doubling absolute pressure halves specific volume.

Molar mass also matters. At the same temperature and pressure, a gas with a larger molar mass has a smaller specific volume per kilogram. This does not mean its molecules occupy less space per mole under the ideal-gas model: at equal temperature and pressure, ideal gases have the same molar volume. The difference comes from how much mass is contained in each mole.

The calculator’s default molar mass, 28.97 g/mol, is a commonly used approximate value for dry air. Air composition can vary, and humid air has a different mean molar mass. Use a suitable value for the actual gas or mixture when accuracy matters; a single pure-compound molar mass should not be applied to an arbitrary mixture.

Pressure, Units, and Common Errors

Pressure in the formula must be absolute pressure, measured from a vacuum. Gauge pressure is measured relative to local atmospheric pressure, so it must be converted before use: absolute pressure equals gauge pressure plus local atmospheric pressure. Entering gauge pressure directly can produce a substantially wrong result, especially near atmospheric conditions.

  • Use kelvins, not degrees Celsius. Convert with T(K) = T(°C) + 273.15. For example, 20 °C is 293.15 K.
  • Use absolute pressure in kPa for this calculator. A value in bar must be converted using 1 bar = 100 kPa; a value in atmospheres uses 1 atm = 101.325 kPa.
  • Enter molar mass in g/mol, not kg/mol. The calculator’s formula accounts for this unit conversion.
  • Keep units consistent if calculating separately. In the SI formula, pressure is Pa and molar mass is kg/mol.

A common misconception is that a gas’s specific volume is a fixed property like the molar mass of a pure substance. It is a state property: its value changes with temperature and pressure, and it also depends on composition.

When the Ideal-Gas Model Is Limited

The ideal-gas equation is a useful approximation when molecules are sufficiently far apart that their individual volumes and intermolecular forces have little effect on bulk behaviour. It often works well for gases at relatively low pressure and temperatures well above condensation conditions. It can become less accurate at high pressure, near a phase change, or at low temperature, where molecular interactions become important.

For a real gas, a common correction is the compressibility factor Z:

v = ZRT / (MP)

Here Z is dimensionless and may depend on the gas and its temperature and pressure. The ideal-gas equation sets Z = 1; this calculator does not estimate Z. For engineering work where non-ideal behaviour matters, obtain a suitable compressibility factor or use an appropriate equation of state and reliable property data. A calculated ideal-gas value should not be presented as a measured real-gas volume.

Frequently Asked Questions

What is the formula for ideal-gas specific volume?
It is v = RT/(MP), or equivalently v = RsT/P. Use absolute temperature and absolute pressure, and keep the units consistent.

What is the specific volume of an ideal gas at standard conditions?
There is no single value unless both the reference temperature and pressure and the gas composition are specified. Because v depends on temperature, pressure, and molar mass, different conventions for standard conditions give different results.

Is specific volume the inverse of density?
Yes. For the same material state, v = 1/ρ, where specific volume is in m3/kg and density is in kg/m3.

Can I enter Celsius or gauge pressure?
Not directly. Convert Celsius to kelvins by adding 273.15, and convert gauge pressure to absolute pressure by adding local atmospheric pressure before entering the value.

Why does molar mass appear in the formula?
The ideal-gas law first gives volume per mole. Dividing by molar mass converts that quantity to volume per unit mass, which is specific volume.

Related

Formula used
in t | Temperature | K | 300 | 0
in p | Absolute pressure | kPa | 101.325 | 0
in mm | Molar mass | g/mol | 28.97 | 0.001
out v | Ideal-gas specific volume | m^3/kg | 8.31446261815324 * t / (p * mm) | 4
out rho | Ideal-gas density | kg/m^3 | 1 / v | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →