molecalculator

Moles & Molar Mass

Second-Order Kinetics Graphs and Rate Equations

Calculator No. 01-6546 · Updated · Formula and assumptions shown below

Concentration remaining [A] 0.0667 mol/L
Reciprocal concentration 1/[A]
15.0000 L/mol
= 1 ÷ Concentration remaining [A]
Initial concentration [A]₀
0.1 mol/L
Set in the form below
Rate constant k
0.5 L/(mol·s)
Set in the form below
You enter
Initial concentration [A]₀ (mol/L), Rate constant k (L/(mol·s)), Elapsed time (s)
You get
Concentration remaining [A] (mol/L), Reciprocal concentration 1/[A] (L/mol)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

For a second-order reaction in one reactant, the key kinetics graph is 1/[A] versus time: a straight line indicates second-order behavior, with slope k and intercept 1/[A]₀. This calculator uses the initial concentration, rate constant, and elapsed time to calculate the concentration remaining and the corresponding reciprocal concentration.

Formula

For a reaction with rate law rate = k[A]², the integrated second-order equation is:

1/[A] = 1/[A]₀ + kt

Equivalently, [A] = 1 / (1/[A]₀ + kt). Here, [A] is the reactant concentration at time t in mol/L; [A]₀ is its initial concentration in mol/L; k is the rate constant in L/(mol·s) when time is measured in seconds; and t is elapsed time in seconds. The calculator’s first result is [A], and its second result is the reciprocal concentration used in the linear graph.

For this particular rate-law convention, the rate of disappearance is −d[A]/dt = k[A]². Some textbooks define reaction rate with a stoichiometric coefficient, so check how the rate is defined before comparing rate constants. The integrated equation applies to a single-reactant second-order rate law under conditions where k remains constant.

Worked Example

Using the defaults, [A]₀ = 0.100 mol/L, k = 0.500 L/(mol·s), and t = 10 s:

  1. Calculate the initial reciprocal concentration: 1/[A]₀ = 1 / 0.100 = 10.000 L/mol.
  2. Calculate the time-dependent term: kt = (0.500 L/(mol·s))(10 s) = 5.0000 L/mol.
  3. Add the terms: 1/[A] = 10.000 + 5.0000 = 15.000 L/mol.
  4. Invert to find the concentration: [A] = 1 / 15.000 = 0.06667 mol/L.

The calculator displays [A] as 0.0667 mol/L and 1/[A] as 15.0000 L/mol, rounded to four decimal places.

Assumptions

  • The reaction follows the single-reactant rate law −d[A]/dt = k[A]² over the time interval.
  • Temperature and other conditions are sufficiently stable that k is constant.
  • Concentration is expressed in mol/L and time in seconds; the rate-constant units must match.
  • This is a study and lab-planning calculation, not a substitute for measured concentration data. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

How to Recognize Second-Order Kinetics

Kinetics graphs test which integrated rate law makes experimental data most nearly linear. For a single reactant A, compare concentration measurements collected at different times using these common plots:

  • Zero order: [A] versus time is linear, with slope −k.
  • First order: ln[A] versus time is linear, with slope −k.
  • Second order: 1/[A] versus time is linear, with slope +k.

For a second-order graph, the vertical axis is reciprocal concentration, not concentration itself. If concentration is measured in mol/L, the vertical-axis unit is L/mol. The graph’s intercept ideally equals 1/[A]₀. A positive slope is expected for a disappearing reactant because its concentration falls while its reciprocal rises.

Real measurements have scatter. A straight-looking line alone does not prove a mechanism: compare plausible plots using residuals and experimental uncertainty, and consider whether the tested concentration range and time points can distinguish the models. A high correlation coefficient is useful but is not, by itself, proof of a reaction order.

What the Graph Tells You

The slope of 1/[A] against time gives k for the stated rate-law convention. Its units follow from the axes: (L/mol)/s = L/(mol·s). The intercept gives 1/[A]₀, so taking its reciprocal estimates the initial concentration. A graph whose intercept differs substantially from the independently prepared initial concentration may indicate measurement error, a poor fit, or a model that does not describe the whole interval.

The equation also gives the half-life. Setting [A] equal to [A]₀/2 yields t₁/₂ = 1/(k[A]₀). Unlike the ideal first-order half-life, this value depends on the starting concentration: doubling [A]₀ halves the second-order half-life when k is unchanged. For the defaults here, t₁/₂ = 1 / ((0.500)(0.100)) = 20 s.

Other Second-Order Cases and Common Mistakes

Not every reaction described as second order follows the exact reciprocal-concentration equation used by this calculator. For a rate law k[A][B] with two different reactants, integration generally involves both concentrations and their initial amounts; the simple 1/[A] plot is not automatically valid. Special cases, including equal initial concentrations for a 1:1 reaction, can simplify, but the appropriate integrated law depends on the stoichiometry and starting conditions.

  • Mixing units: If k is in L/(mol·s), enter concentration in mol/L and time in seconds. Convert minutes to seconds before using the equation.
  • Using the wrong graph: Plotting [A] instead of 1/[A] does not test the integrated second-order form.
  • Confusing reaction order with coefficients: Rate-law exponents are determined experimentally; they cannot generally be read from the balanced equation.
  • Rounding too early: Keep extra digits during calculations, especially when taking reciprocals, and round the reported answer to match the precision of the data.
  • Extrapolating too far: The equation predicts the ideal model. Side reactions, changing conditions, or detection limits can make long-time predictions unreliable.

Frequently Asked Questions

What graph is linear for a second-order reaction?
For a single reactant with rate law −d[A]/dt = k[A]², plot 1/[A] against time. The ideal slope is k and the intercept is 1/[A]₀.

Is the slope of a second-order plot positive or negative?
It is positive for 1/[A] versus time when A is being consumed. The reciprocal concentration increases as [A] decreases.

What are the units of a second-order rate constant?
For rate = k[A]², k has units of concentration⁻¹ time⁻¹, commonly L/(mol·s) when concentration is in mol/L and time is in seconds.

Does every second-order reaction use a 1/[A] graph?
No. That graph follows directly for a single-reactant rate law proportional to [A]². A rate law involving two different reactants may require a different integrated equation or a special-case treatment.

How does initial concentration affect second-order half-life?
For the single-reactant equation, t₁/₂ = 1/(k[A]₀). With the same k, a higher initial concentration gives a shorter half-life.

Can a straight line prove a second-order mechanism?
No. It supports the model over the measured range, but experimental uncertainty and competing models matter. Assess residuals, data quality, and whether the proposed rate law is chemically plausible.

Related

Formula used
in a0 | Initial concentration [A]₀ | mol/L | 0.100 | 0
in k | Rate constant k | L/(mol·s) | 0.500 | 0
in t | Elapsed time | s | 10 | 0
out a | Concentration remaining [A] | mol/L | 1 / (1 / a0 + k * t) | 4
out inv | Reciprocal concentration 1/[A] | L/mol | 1 / a | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →