molecalculator

Moles & Molar Mass

Lift Traffic Analysis Calculator: How to Use One

Calculator No. 01-9981 · Updated · Formula and assumptions shown below

5-minute handling capacity 26.0 %
Interval
30 s
= Round trip time ÷ Number of lifts
Building population
500 people
Set in the form below
Lift capacity
13 persons
Set in the form below
You enter
Building population (people), Lift capacity (persons), Round trip time (s), Number of lifts
You get
5-minute handling capacity (%), Interval (s)
Rounding
1 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A lift traffic analysis calculator works out how many passengers a lift (elevator) can move in a given time, typically expressed as a 5-minute handling capacity (HC5) as a percentage of the building’s population. You enter the building population, the lift’s capacity, speed, door times, and the number of lifts, and it returns the interval between lift arrivals and the percentage of people moved in five minutes. This is the core arithmetic used in lift traffic design to check whether a proposed lift configuration will meet the demand of an office, hotel, or residential building.

Formula

The two fundamental quantities in lift traffic analysis are the interval and the 5-minute handling capacity.

Interval (I) = RTT / N

  • RTT = round trip time in seconds (the time for one lift to leave the main floor, serve all its calls, and return)
  • N = number of lifts in the group

Handling capacity (HC5) = (N × C × 300) / RTT / P × 100%

  • C = capacity of one lift in persons
  • 300 = number of seconds in 5 minutes
  • P = building population (total number of people to be served)

The result HC5 is the percentage of the building population that the lift group can move in the busiest five minutes. The interval is the average time between successive lift arrivals at the main floor.

Worked Example

Using the default inputs: population = 500, lift capacity = 13 persons, round trip time = 120 s, number of lifts = 4.

First, the interval: I = RTT / N = 120 / 4 = 30 s.

Next, the number of people moved in 5 minutes: each lift can carry 13 persons per trip. In 300 seconds, one lift makes 300 / 120 = 2.5 trips, so it moves 13 × 2.5 = 32.5 persons. Four lifts move 4 × 32.5 = 130 persons. As a percentage of 500: (130 / 500) × 100 = 26%.

The calculator gives the same result: (4 × 13 × 300 / 120) / 500 × 100 = 26.0%.

Assumptions

  • The round trip time is an input, not calculated here; it must be estimated from the building height, speed, acceleration, door times, and passenger transfer times.
  • Passenger demand is uniformly distributed over the five-minute peak.
  • All lifts have the same capacity and speed and are equally loaded.
  • No up-peak or down-peak bias is considered; this is a simplified average.

Where the Round Trip Time Comes From

The calculator above is only half the story. The round trip time (RTT) is the real heart of lift traffic analysis, and it is usually estimated with a more detailed formula that breaks the journey into parts:

  • Travel time: time to accelerate, run at full speed, and decelerate for the highest call – depends on rated speed and acceleration.
  • Door operating time: opening and closing at the main floor and at each stop.
  • Passenger transfer time: typically 0.8–1.2 seconds per passenger entering or leaving.
  • Number of probable stops: a statistical estimate based on capacity and the number of floors above the main terminal.

For a quick estimate, you can use a simplified RTT formula: RTT = 2 × H / v + (S + 1) × T_door + 2 × P × T_transfer, where H = highest call height, v = rated speed, S = expected number of stops, T_door = total door time per stop, P = number of passengers in the car. Many traffic design programs use more sophisticated Monte Carlo simulations, but the basic arithmetic above gives a useful first check.

Interpreting the Results

Lift traffic designers use the following rough benchmarks for office buildings during the morning up-peak:

  • HC5 above 12–15% is generally considered acceptable for an office building.
  • Interval below 30 seconds is perceived as good; above 40 seconds is often seen as slow.
  • For residential buildings, the target HC5 is lower, around 5–10%, because demand is less intense.

If your calculated HC5 is below the target, you can increase the number of lifts, increase capacity, or reduce round trip time (faster speed, better door operation, or destination dispatch). The calculator lets you test these changes quickly.

Common Mistakes and Limitations

  • Mixing units: ensure round trip time is in seconds, not minutes. If you enter minutes, the handling capacity will be 60 times too high.
  • Using the wrong population: the population should be the peak-period users, not the total building occupancy. In an office, that is roughly 70–80% of the total staff.
  • Assuming a constant RTT: the round trip time varies with the number of passengers and the distribution of calls. A single number is a simplification.
  • Ignoring up-peak vs. down-peak: the morning up-peak is the most demanding; the calculator assumes that all passengers are going up from the main floor, which is the usual design case.

The formula is a planning tool, not a substitute for a full traffic simulation. For complex buildings, lift consultants use software that models passenger arrivals, car dispatching, and destination control. The simple calculator here helps you understand the relationships and get a first estimate.

How to Choose the Right Inputs

To get a useful result, you need realistic numbers:

  • Population: use the number of people who will be in the building during the peak. For an office, that is the number of workstations or employees, not the maximum fire evacuation load.
  • Capacity: typical lift capacities are 8, 10, 13, 16, or 21 persons. Check the lift data sheet.
  • Round trip time: if you don’t have a measured value, estimate it as: 2 × (highest floor height / speed) + (number of stops + 1) × door time + 2 × passengers × transfer time. For example, a 10-floor building with 1.6 m/s speed, 10 stops, 2 s door time, and 13 passengers: 2×(30/1.6) + 11×2 + 2×13×1 = 37.5 + 22 + 26 = 85.5 s. Use that as a starting point.

Frequently Asked Questions

What is a good 5-minute handling capacity? For an office building, 12–15% is generally the minimum acceptable; 20% is considered excellent. Residential buildings can operate with 5–10% because the peak demand is lower.

How do I calculate round trip time without a simulator? Use the simplified formula: RTT = 2 × H/v + (S+1) × T_door + 2 × P × T_transfer. H is the height to the highest call, v is the rated speed, S is the expected number of stops, T_door is the total door open/close time per stop, P is the number of passengers in the car, and T_transfer is the time per passenger entering/exiting (around 1 s).

What is the difference between interval and waiting time? The interval is the average time between lift arrivals at the main floor. The waiting time is the time a passenger actually waits, which is typically about half the interval on average, but varies. A 30-second interval means an average wait of about 15 seconds.

Does this calculator work for destination dispatch systems? It gives a rough estimate, but destination dispatch changes the round trip time because passengers are grouped by destination, reducing the number of stops. You would need a lower number of stops in your RTT estimate, or use a dedicated simulation.

Why does my building’s lift seem slow even though the calculator says it’s fine? The calculator uses average values. In reality, demand is not uniform – there are bursts of passengers, and some lifts may be delayed by maintenance or special events. Also, the calculator assumes all lifts are working; if one is out of service, the interval increases by a factor of N/(N-1).

Safety and Scope

This calculator is for planning and educational purposes only. Actual lift traffic design should be done by a qualified lift consultant or engineer who can account for building-specific factors, local codes, and safety requirements. Always follow the lift manufacturer’s specifications and the applicable building code in your region.

Related

Formula used
in p | Building population | people | 500 | 1
in c | Lift capacity | persons | 13 | 1
in t | Round trip time | s | 120 | 10
in n | Number of lifts | - | 4 | 1
out hc5 | 5-minute handling capacity | % | (n * c * 300 / t) / p * 100 | 1
out int | Interval | s | t / n | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →