Convert liters per hour (L/h) to U.S. gallons per hour (gph) by multiplying by 0.264172: 1 L/h is about 0.2642 U.S. gph. Enter a flow rate in L/h to get the equivalent U.S. gallons per hour, plus the corresponding imperial gallons per hour for comparison.
Formula
For U.S. gallons per hour, divide the rate in liters per hour by 3.785411784. This factor is the exact number of liters in one U.S. liquid gallon. In symbols:
- QU.S. = QL / 3.785411784
- QImp. = QL / 4.54609
QL is the flow rate in liters per hour (L/h); QU.S. is the rate in U.S. gallons per hour; and QImp. is the rate in imperial gallons per hour. The imperial conversion uses 4.54609 liters per imperial gallon. These are volume-flow conversions: they change the unit, not the actual amount of liquid moving over time.
Worked Example
Using the calculator’s default input, 100 L/h:
- U.S. gallons per hour: 100 L/h ÷ 3.785411784 L/U.S. gal = 26.417205 L/h in U.S. gallons, or 26.4172 U.S. gph when rounded to four decimal places.
- Imperial gallons per hour: 100 L/h ÷ 4.54609 L/Imp. gal = 22.003847 L/h in imperial gallons, or 22.0038 Imp. gph to four decimal places.
The units cancel in each division, leaving gallons per hour. If you only need a quick estimate, 100 L/h is roughly 26.4 U.S. gph.
Assumptions
- The input is a volume flow rate in liters per hour, not a volume by itself.
- “Gallon” is ambiguous, so the calculator reports U.S. liquid gallons and imperial gallons separately.
- The conversion treats the listed rates as exact unit conversions; measurement uncertainty in the original flow rate is not included.
When to Use This Conversion
L/h to gph conversion is useful when a flow rate is provided in metric units but a specification, chart, or calculation uses gallons per hour. It may come up when comparing pumps, circulation rates, water-use figures, or process-flow readings. The arithmetic is the same regardless of liquid, provided the original figure is a volume per unit time.
Check that the source figure really is L/h. A value in liters per minute (L/min) is 60 times larger than the same numerical value in L/h; a value in liters per second is 3,600 times larger. Converting the wrong time unit can produce a result that is dramatically off even though the gallon conversion itself is correct.
Also distinguish flow rate from capacity. A container holding 100 liters is a volume, not a rate. It cannot be converted to gallons per hour unless you also know how long it takes to fill, empty, or pass that volume. For example, a 100-liter volume transferred over two hours corresponds to 50 L/h; that rate is approximately 13.2086 U.S. gph.
U.S. and Imperial Gallons
There are two commonly used gallon definitions. A U.S. liquid gallon is exactly 3.785411784 liters, while an imperial gallon is exactly 4.54609 liters. Because an imperial gallon is larger, a given L/h rate produces a smaller numerical value in imperial gph. At 100 L/h, for instance, the result is about 26.42 U.S. gph but 22.00 imperial gph.
This difference is not a rounding issue. The two gallons are different-sized units, so a bare “gph” can be unclear. When accuracy matters, write “U.S. gph” or “Imp. gph,” and check which definition the equipment documentation or destination country uses. Do not assume that a pump’s stated gph is imperial simply because the equipment is used outside the United States; consult its specification.
Common Conversion Mistakes
- Using the wrong gallon: Dividing by 3.785411784 gives U.S. gph; dividing by 4.54609 gives imperial gph.
- Multiplying instead of dividing: Since a gallon contains several liters, a rate expressed in gallons per hour has a smaller number than the same rate in liters per hour.
- Mixing time units: Convert minutes or seconds to hours before treating a rate as L/h. For example, 1 L/min is 60 L/h, not 1 L/h.
- Rounding too early: Keep the conversion factor through the calculation and round the final result to a precision suitable for the input. A display with many decimal places does not make an imprecise meter reading more accurate.
- Confusing flow with pressure or pump capacity: This calculation converts a stated flow rate only. It does not predict what a pump will deliver under a particular pressure, pipe size, or operating condition.
Related Flow-Rate Conversions
The same unit definitions make reverse conversion straightforward: multiply U.S. gph by 3.785411784 to get L/h, or multiply imperial gph by 4.54609 to get L/h. To convert L/h to liters per minute, divide by 60; to convert L/h to liters per second, divide by 3,600. For example, 60 L/h equals 1 L/min and approximately 0.2642 U.S. gph.
When comparing equipment, use the flow rate at the relevant operating conditions rather than treating a unit conversion as a performance estimate. Actual delivered flow can depend on the system and the measurement conditions. The conversion can put two published figures in the same units, but it cannot make unlike test conditions equivalent.
Frequently Asked Questions
How many U.S. gallons per hour is 1 liter per hour?
One L/h is approximately 0.264172 U.S. gph. The exact conversion is 1 ÷ 3.785411784.
How do I convert L/h to gph?
For U.S. gallons per hour, divide L/h by 3.785411784. For imperial gallons per hour, divide by 4.54609.
Is gph U.S. or imperial?
The abbreviation alone does not reliably identify which gallon is meant. Check the source or specification, and label the result U.S. gph or imperial gph when possible.
How many U.S. gph is 100 L/h?
100 L/h is approximately 26.4172 U.S. gph. In imperial units it is approximately 22.0038 Imp. gph.
How do I convert liters per minute to gph?
First multiply L/min by 60 to obtain L/h, then divide by 3.785411784 for U.S. gph, or by 4.54609 for imperial gph.
Related
Formula used
in lph | Flow rate | L/h | 100 | 0 out gph | U.S. gallons per hour | U.S. gph | lph / 3.785411784 | 4 out igph | Imperial gallons per hour | Imp. gph | lph / 4.54609 | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s