molecalculator

Moles & Molar Mass

Liters per Minute Calculator: Convert Flow Rates

Calculator No. 01-6296 · Updated · Formula and assumptions shown below

Flow rate 60.000 L/min
Flow rate
3,600.00 L/h
= Flow rate × 60
Flow rate
1,000.00 mL/s
= Flow rate × 1000 ÷ 60
Volume
60 L
Set in the form below
You enter
Volume (L), Elapsed time (min)
You get
Flow rate (L/min), Flow rate (L/h), Flow rate (mL/s)
Rounding
3 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A liters per minute calculator converts a liquid or gas flow rate into liters per minute (L/min), or converts L/min to another time or volume unit. Enter the volume and the time over which it flows; the calculator returns the flow rate, assuming both measurements describe the same flow and use compatible units.

Formula

Flow rate is volume divided by elapsed time: Q = V / t. In this calculator, Q is the flow rate in liters per minute (L/min), V is the measured volume in liters (L), and t is the elapsed time in minutes (min). To express the same rate in liters per hour, multiply L/min by 60 minutes per hour. To express it in milliliters per second, multiply L/min by 1,000 mL/L and divide by 60 seconds per minute.

The formula describes an average rate over the measured interval. It does not assume that the flow stayed perfectly constant during that interval. If the flow varies, the result is still the total volume divided by the total time, not necessarily the instantaneous rate at any particular moment.

Worked Example

Using the calculator’s default inputs, 60 L flows over 1 min.

  • L/min: Q = 60 L / 1 min = 60.000 L/min.
  • L/h: 60.000 L/min × 60 min/h = 3,600.00 L/h.
  • mL/s: 60.000 L/min × 1,000 mL/L / 60 s/min = 1,000.00 mL/s.

These are different expressions of the same rate. The conversion factors cancel the original units and leave the units shown in each result.

Assumptions

  • The volume and time refer to the same flow interval and flow path.
  • The input volume is in liters and elapsed time is in minutes.
  • The reported value is an average flow rate; no constant-flow assumption is needed to calculate that average.
  • For gases, the volume is meaningful only with its pressure and temperature conditions understood. This arithmetic does not correct gas volumes to a reference condition.

How to Use the Calculator

Enter a measured volume in liters and the time taken in minutes. The first result is the average flow in L/min; the other outputs show equivalent rates in L/h and mL/s. The calculator accepts positive values only. Convert your measurements before entering them if they use different units.

For example, if you collect 750 mL in 30 seconds, first convert the measurements: 750 mL is 0.750 L, and 30 seconds is 0.5 min. Then Q = 0.750 L / 0.5 min = 1.5 L/min. Alternatively, the same rate is 90 L/h or 25 mL/s. This conversion is useful whenever the original measurements are not already in liters and minutes.

For a timed collection, start the timer when flow begins and stop it at the same defined point at which you measure the collected volume. When reading a flow meter, record its units and the interval it represents. A meter reading may show an instantaneous or rolling rate, while volume divided by elapsed time gives an average over the chosen interval.

Conversions and Comparisons

“Liter per minute,” “liters per minute,” and “L/min” refer to the same unit. Common equivalents are:

  • 1 L/min = 60 L/h.
  • 1 L/min = 1,000 mL/min.
  • 1 L/min = 16.6667 mL/s.
  • 1 L/min = 0.001 m³/min, because 1 m³ = 1,000 L.

These conversions change only the way a rate is written, not the amount of fluid flowing. Do not confuse L/min with L/h: a rate of 60 L/min is 3,600 L/h, not 60 L/h. Similarly, mL/s and L/min differ by a factor of 16.6667, so copying a number while changing its unit can create a substantial error.

To compare two flow rates, put them in the same units first. For instance, 900 mL/min is 0.9 L/min, while 50 mL/s is 3 L/min. The latter rate is greater even though its numerical value, 50, is smaller than 900. Units determine what a number means.

Common Errors and Limits

  • Mixing units: Do not divide milliliters directly by minutes and label the result L/min. Convert milliliters to liters by dividing by 1,000.
  • Using the wrong time scale: Convert seconds to minutes by dividing by 60, or convert hours to minutes by multiplying by 60.
  • Using a partial interval: Make sure the recorded time covers the full volume being counted. A start or stop delay changes the calculated rate.
  • Over-rounding: Keep enough digits during conversions, then round the final answer to match the measurement precision. Extra decimal places do not make an imprecise measurement more accurate.

This calculation does not determine pressure, pump performance, friction losses, fluid viscosity, or whether equipment can safely carry a given flow. Those questions require system details and, where relevant, engineering data. For gases, liters at different pressures or temperatures do not necessarily contain the same amount of gas; comparing such volumes may require correcting them to the same stated conditions. A simple L/min conversion cannot supply those missing conditions.

For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. Use appropriate equipment and procedures for the material and pressure involved; a calculated flow rate alone is not a safety assessment.

Frequently Asked Questions

How do I calculate liters per minute?
Divide the volume in liters by the elapsed time in minutes. For example, 12 L collected in 4 minutes gives 12 / 4 = 3 L/min.

How many liters per minute is one liter per hour?
Divide L/h by 60 to get L/min. One liter per hour is 1/60, or about 0.0167 L/min.

How do I convert mL/s to L/min?
Multiply mL/s by 60 and divide by 1,000. For example, 25 mL/s × 60 / 1,000 = 1.5 L/min.

Is L/min an instantaneous or average flow rate?
It can describe either, depending on how the value was obtained. Dividing a total volume by total elapsed time gives an average; a suitable meter may report a rate at a particular moment or over a short rolling interval.

Can I compare gas flow rates in L/min directly?
Only when the volume measurements use comparable pressure and temperature conditions. Gas volume changes with those conditions, so check whether the value is actual flow or is corrected to a stated reference condition.

Related

Formula used
in vol | Volume | L | 60 | 0
in time | Elapsed time | min | 1 | 0.000001
out lpm | Flow rate | L/min | vol / time | 3
out lph | Flow rate | L/h | lpm * 60 | 2
out mlps | Flow rate | mL/s | lpm * 1000 / 60 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →