molecalculator

Moles & Molar Mass

Liter to CFM Calculator: Convert L/min to Airflow

Calculator No. 01-6297 · Updated · Formula and assumptions shown below

Airflow 3.53 ft³/min (CFM)
Airflow
1.667 L/s
= Airflow ÷ 60
Airflow
100 L/min
Set in the form below
You enter
Airflow (L/min)
You get
Airflow (ft³/min (CFM)), Airflow (L/s)
Rounding
2 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A liter-to-CFM calculator converts a volumetric flow rate from liters per minute (L/min) to cubic feet per minute (CFM). Enter the airflow in L/min to get CFM; the conversion assumes both values describe the same volume of air per unit time.

Formula

To convert liters per minute to cubic feet per minute, multiply the flow rate by the number of cubic feet in one liter:

CFM = Q × 0.0353146667

  • Q is the input airflow in liters per minute (L/min).
  • 0.0353146667 ft³/L is the volume conversion factor, based on 1 cubic foot = 28.316846592 liters.
  • CFM is cubic feet per minute, a volumetric flow rate.

The calculator also reports liters per second: L/s = Q / 60, since one minute contains 60 seconds. These are unit conversions only; they do not adjust for pressure, temperature, humidity, or the way a flow instrument reports its reading.

Worked Example

Using the default input of 100 L/min:

  1. Convert the volume unit: 1 L = 0.0353146667 ft³.
  2. Multiply by the flow rate: 100 L/min × 0.0353146667 ft³/L = 3.53146667 ft³/min.
  3. Rounded to two decimal places, the result is 3.53 CFM.
  4. For the secondary output: 100 L/min / 60 = 1.6666667 L/s, or 1.667 L/s to three decimal places.

Assumptions

  • The input is a volumetric flow rate in liters per minute, not a volume in liters alone.
  • The input and output refer to the same flow conditions and same stream of gas or liquid.
  • The conversion uses the exact relation 1 ft³ = 28.316846592 L; rounding is applied only to display.
  • No correction is made for reference conditions, compressibility, or instrument calibration.

How the Conversion Works

A liter and a cubic foot are units of volume. A flow rate combines a volume unit with a time unit. Because this conversion keeps the time unit as minutes, only the volume units need to change: liters become cubic feet, while “per minute” remains unchanged.

One cubic foot equals 28.316846592 liters, so one liter equals 1 / 28.316846592 cubic feet, approximately 0.0353146667 cubic feet. Multiplying an L/min value by that factor gives ft³/min. The letters CFM stand for cubic feet per minute; they are simply a common way to write ft³/min.

For example, a fan rated at 500 L/min converts to 500 × 0.0353146667 = 17.6573 CFM, approximately 17.66 CFM. Conversely, to convert CFM to L/min, divide by 0.0353146667, or multiply by 28.316846592.

Units, Similar Terms, and Comparisons

“Liter” by itself measures volume, not airflow. To calculate CFM, the input must include a time basis, such as L/min or L/s. A container holding 100 liters is not equivalent to an airflow of 100 L/min; the latter also specifies how quickly that volume passes a point.

  • L/min to CFM: multiply by 0.0353146667.
  • L/s to CFM: multiply by 2.11888000, since 60 seconds make one minute.
  • CFM to L/min: multiply by 28.316846592.
  • m³/h to CFM: multiply by approximately 0.588578, after confirming the input is cubic meters per hour.

These factors follow from unit definitions. If a specification uses another time base, convert that time as well as the volume. Do not apply the L/min factor directly to m³/h, L/s, or a plain volume reading.

Choosing and Interpreting an Airflow Value

A conversion tells you how two units express the same reported rate; it does not tell you whether that rate is suitable for a particular task. The appropriate airflow depends on the application, system design, operating conditions, and how the rate was measured. When comparing equipment or technical specifications, check all of the following:

  • Rate unit: Confirm whether the number is L/min, L/s, CFM, or another unit.
  • Measurement conditions: Gas flow may be reported at actual conditions or at stated reference conditions. Pressure and temperature affect gas density and can matter when comparing ratings.
  • Operating point: A device’s delivered flow can vary with resistance, pressure, or its position in a system. A free-flow figure may not describe its flow when connected to a load.
  • Measurement type: Check the instrument’s stated accuracy, range, and calibration when precision matters.
  • Rounding: Keep extra digits during intermediate calculations and round only the final displayed result to the precision useful for the measurement.

For a simple unit comparison, the calculator’s direct conversion is appropriate. For engineering or process decisions, the reference conditions and measurement method may be just as important as the converted number.

Common Conversion Mistakes and Limits

A frequent error is multiplying by 28.3168 when converting L/min to CFM. That factor goes in the opposite direction: it converts CFM to L/min. For L/min to CFM, use its reciprocal, approximately 0.0353147. A quick sense check helps: because a cubic foot is about 28.3 liters, a flow expressed in CFM should have a smaller number than the same flow expressed in L/min.

Another mistake is confusing L/min with L/s. Since a minute is 60 seconds, 60 L/min equals 1 L/s, which is about 2.11888 CFM. A result off by a factor of 60 usually indicates a time-unit mix-up.

The conversion also does not account for whether a gas-flow figure is “standard” or “actual.” Those labels refer to conditions used to define or measure the gas volume. If two specifications use different conditions, their numerical flow rates may not be directly comparable even after converting units. Use the condition definitions supplied with the measurement or equipment rating; this calculator does not infer or correct them.

Frequently Asked Questions

How many CFM is 1 liter per minute?
One L/min is approximately 0.0353147 CFM. The conversion is 1 × 0.0353146667.

How do I convert L/min to CFM?
Multiply the L/min value by 0.0353146667. For example, 200 L/min is about 7.06 CFM.

How do I convert CFM back to L/min?
Multiply the CFM value by 28.316846592. For instance, 10 CFM is about 283.17 L/min.

Is CFM the same as L/min?
They measure the same kind of quantity—volume per time—but use different volume units. One CFM is approximately 28.3168 L/min.

Does this calculator adjust for air pressure or temperature?
No. It changes units only. To compare gas flows reported at different pressure or temperature reference conditions, use the conditions and correction method specified for those measurements.

Related

Formula used
in flow | Airflow | L/min | 100 | 0
out cfm | Airflow | ft³/min (CFM) | flow * 0.0353146667 | 2
out lps | Airflow | L/s | flow / 60 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →