To convert liters to kilograms, you multiply the volume in liters by the density of the substance in kilograms per liter (kg/L). Because density varies with the material and temperature, there is no single conversion factor; 1 liter of water weighs 1 kg at 4 °C, but 1 liter of olive oil weighs about 0.92 kg.
Formula
The relationship between volume, density, and mass is:
mass (kg) = volume (L) × density (kg/L)
Where:
- mass is the result in kilograms (kg)
- volume is the amount of liquid or substance in liters (L)
- density is the mass per unit volume of the substance in kilograms per liter (kg/L)
Density is often given in grams per milliliter (g/mL) or grams per cubic centimeter (g/cm³). Since 1 mL = 1 cm³ and 1 g/mL = 1 kg/L, the numeric value is the same in all three units. For example, water has a density of 1.0 g/mL, which equals 1.0 kg/L.
Worked Example
Using the default values from the calculator: volume = 2 L and density = 1.000 kg/L (pure water at 4 °C).
Step 1: Write the formula.
mass = volume × density
Step 2: Insert the numbers.
mass = 2 L × 1.000 kg/L
Step 3: Multiply.
mass = 2.000 kg
The calculator shows 2.000 kg for the mass and 2000.0 g for the mass in grams. If you change the density to 0.92 kg/L (olive oil), the same 2 L gives 1.84 kg.
Assumptions
- The density is constant throughout the volume (homogeneous substance).
- The temperature is the one at which the density was measured; density changes with temperature for most liquids.
- The substance is in the liquid or solid state, not a gas (gas densities are much lower and vary strongly with pressure).
- The volume is the actual volume of the substance, not the container capacity with air gaps.
Why Density Changes with Temperature
Most liquids expand when heated, so the same mass occupies a larger volume. This means the density (mass per volume) decreases as temperature rises. For water, the density is highest at about 4 °C (1.000 kg/L) and decreases slightly above and below that. At 20 °C, water density is about 0.998 kg/L; at 80 °C, it drops to about 0.972 kg/L. If you measure a liter of hot water, it will weigh less than a liter of cold water.
For cooking oils, the density change with temperature is more noticeable than for water. A recipe that calls for a liter of oil at room temperature will give a slightly different mass if the oil is warm. In industrial and laboratory settings, density is often reported at a standard temperature (e.g., 20 °C or 25 °C) so that conversions are reproducible.
Common Substances and Their Densities
Here are approximate densities at 20 °C unless noted. These are typical values; check a specific data sheet for exact numbers.
- Water (4 °C): 1.000 kg/L
- Water (20 °C): 0.998 kg/L
- Milk (whole, ~20 °C): about 1.03 kg/L
- Olive oil: about 0.92 kg/L
- Ethanol (pure): 0.789 kg/L
- Gasoline (varies): about 0.72–0.78 kg/L
- Honey: about 1.42 kg/L
- Mercury: 13.534 kg/L
Notice that honey and mercury are denser than water, so a liter of each weighs more than a kilogram. Gasoline and oils are less dense, so a liter weighs less than a kilogram.
How to Find the Density You Need
If you are converting a common liquid, look up its density in a reference table or on the product label. Many industrial chemicals list density on the safety data sheet (SDS) under physical properties. For a mixture or solution, the density depends on concentration—for example, a 20% salt solution has a higher density than pure water because the dissolved salt adds mass without changing volume much.
If you have the density in g/mL, use it directly as kg/L because the numbers are equal. If the density is given in kg/m³, divide by 1000 to get kg/L (1 kg/m³ = 0.001 kg/L). For example, a density of 1000 kg/m³ is 1.000 kg/L.
For solids like flour or sand, the “density” in a conversion is usually the bulk density, which includes air spaces between particles. A liter of all-purpose flour weighs about 0.5–0.6 kg, but a liter of water weighs 1 kg. Bulk density varies with how tightly the material is packed, so volume-to-mass conversions for powders are less precise than for liquids.
Common Mistakes and Misconceptions
One frequent error is assuming 1 L always equals 1 kg. This is only true for water at 4 °C. For any other substance, the mass differs. Another mistake is using the density of water for a liquid that is not water—for example, converting liters of milk or juice as if they were water. Milk is slightly denser, so 1 L of whole milk weighs about 1.03 kg, not 1 kg.
Another issue is ignoring temperature. If you measure a hot liquid and use a density value for 20 °C, your result will be slightly off. For most everyday purposes, the error is small (less than 2% for water between 4 °C and 80 °C), but for precise laboratory work, temperature matters.
Also, be careful with units. Density in g/mL is numerically equal to kg/L, but density in kg/m³ is 1000 times larger. Converting 1 kg/m³ to kg/L requires dividing by 1000. A simple unit mix-up here can lead to results that are off by a factor of 1000.
Practical Applications
Converting liters to kilograms is common in cooking, shipping, and chemistry. In recipes, ingredients like oil, honey, or milk are often measured by volume, but nutritional information is given by mass. In shipping, you may need to estimate the weight of a liquid cargo from its volume. In a laboratory, you might prepare a solution by weighing a liquid reagent instead of measuring its volume, because mass is more accurate.
For example, if a recipe calls for 0.5 L of honey, and you want to know how much that weighs, multiply 0.5 L by 1.42 kg/L to get 0.71 kg. If you are shipping a 200 L drum of ethanol, the mass is 200 L × 0.789 kg/L = 157.8 kg. These calculations are straightforward once you have the correct density.
Limits of the Simple Conversion
The formula mass = volume × density assumes the substance is uniform and incompressible. For gases, density changes dramatically with pressure and temperature, so a liter of air at sea level weighs about 0.0012 kg, but at high altitude it weighs less. For this reason, the calculator is intended for liquids and solids, not gases.
For solutions, the density depends on concentration. If you mix two liquids, the final volume may not be exactly the sum of the individual volumes (e.g., water and ethanol contract slightly), so the density of the mixture is not a simple average. Always use the measured density of the final solution.
Finally, the conversion gives mass, not weight. Weight is the force of gravity on that mass. On Earth, 1 kg of mass weighs about 9.81 newtons, but in everyday language “weight” is often used to mean mass. The calculator returns mass in kilograms, which is what most people mean when they ask “how much does it weigh?”
Frequently Asked Questions
How many kg is 1 liter of water?
At 4 °C, 1 liter of pure water has a mass of exactly 1 kg because its density is 1.000 kg/L. At room temperature (20 °C), it is 0.998 kg, so for most purposes you can still use 1 kg.
Is 1 liter always 1 kg?
No. The equality holds only for water at 4 °C. For other substances, the mass depends on density. For example, 1 L of olive oil is about 0.92 kg, and 1 L of honey is about 1.42 kg.
How do I convert liters to kg without a density?
You cannot do it accurately without knowing the density. If the substance is water, you can assume 1 kg/L for everyday use. For anything else, look up the density or measure it (e.g., weigh a known volume).
What is the difference between liters and kilograms?
Liters measure volume (how much space something occupies), while kilograms measure mass (how much matter it contains). They are different physical quantities, so a direct conversion requires density.
Does temperature affect the conversion?
Yes. Most liquids expand when heated, so their density decreases. Using a density measured at a different temperature will give a slightly inaccurate mass. For precision, use the density at the same temperature as the liquid.
Can I convert liters to kg for gases?
Technically yes, but gas density varies greatly with pressure and temperature. For example, air at sea level has a density of about 0.0012 kg/L, but at high altitude it is lower. This calculator is best for liquids and solids.
Related
Formula used
in v | Volume | L | 2 | 0 in d | Density | kg/L | 1.000 | 0 out m | Mass | kg | v * d | 3 out mg | Mass in grams | g | m * 1000 | 1
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- RPM to Distance Calculator: How to Convert314.16 m
- Electric Motor RPM: What It Is and How to Calculate It1,800 RPM
- RPM from G Force: Convert Centrifugal Force2,990 RPM
- RPM Formula for Lathe: Calculate Spindle Speed955 RPM
- Rotational Speed to RPM: How to Convert
- RPM and Diameter to Speed Calculator2.62 m/s