molecalculator

Moles & Molar Mass

RPM and Diameter to Speed Calculator

Calculator No. 01-7370 · Updated · Formula and assumptions shown below

Linear speed (m/s) 2.62 m/s
Speed (km/h)
9.42 km/h
= Linear speed (m÷s) × 3.6
Speed (mph)
5.86 mph
= Linear speed (m÷s) × 2.2369362920544
Rotational speed (RPM)
100 rpm
Set in the form below
You enter
Rotational speed (RPM) (rpm), Diameter (m)
You get
Linear speed (m/s) (m/s), Speed (km/h) (km/h), Speed (mph) (mph)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts rotational speed in revolutions per minute (RPM) and the diameter of a rotating object (such as a wheel, pulley, or disc) into linear speed — the distance that a point on the outer edge travels per unit time. You enter the RPM and the diameter (in meters, centimeters, or any unit you choose, as long as you use the same unit for the result), and you get the linear speed in meters per second, kilometers per hour, and miles per hour.

Formula

The relationship between rotational speed and linear speed is straightforward. The linear speed \( v \) of a point on the rim of a rotating object is the product of the angular speed and the radius. In terms of RPM and diameter:

\( v = \frac{\text{RPM} \times \pi \times d}{60} \)

Where:

  • \( v \) = linear speed at the outer edge (m/s)
  • \( \text{RPM} \) = revolutions per minute (dimensionless count per minute)
  • \( d \) = diameter of the rotating object (m, but any unit works if you keep it consistent)
  • \( \pi \) ≈ 3.14159

The factor 60 converts minutes to seconds. The circumference of a circle is \( \pi d \), so each revolution moves a point on the rim by that distance. Multiplying by RPM gives distance per minute, then dividing by 60 gives distance per second.

Worked Example

Using the default values from the calculator: RPM = 100, diameter = 0.5 m.

  1. Circumference = \( \pi \times 0.5 = 1.57079632679 \) m
  2. Distance per minute = \( 100 \times 1.57079632679 = 157.079632679 \) m/min
  3. Convert to m/s: \( 157.079632679 / 60 = 2.61799437798 \) m/s
  4. Rounded to 2 decimals: 2.62 m/s
  5. Convert to km/h: \( 2.61799437798 \times 3.6 = 9.42477976073 \) km/h → 9.42 km/h
  6. Convert to mph: \( 2.61799437798 \times 2.2369362920544 = 5.856 \) mph → 5.86 mph

So a wheel with a 0.5 m diameter spinning at 100 RPM moves its outer edge at about 2.62 m/s, which is roughly 9.42 km/h or 5.86 mph.

Assumptions

  • The object is a perfect circle or the measurement is taken at the outermost radius.
  • The speed is measured at the outer edge of the rotating part, not at the center or at an intermediate radius.
  • RPM is constant (no acceleration or deceleration during measurement).
  • There is no slipping between the rotating object and the surface it contacts (if you are using this for a wheel on a road, the wheel must not spin freely).

When to Use This Conversion

This conversion appears in many practical situations:

  • Calculating the surface speed of a grinding wheel or lathe workpiece (often called cutting speed).
  • Estimating the speed of a vehicle from wheel RPM and tire diameter.
  • Designing belt and pulley systems where the linear speed of the belt is needed.
  • Determining the tip speed of a fan blade or a wind turbine rotor.
  • Converting the rotational speed of a motor to the linear speed of a conveyor belt (using the pulley diameter).

In machining, the relationship is often expressed as cutting speed in meters per minute (m/min) or surface feet per minute (SFPM). The formula is the same, but you might not divide by 60 if you want m/min. For example, a 10 mm drill bit (diameter 0.01 m) spinning at 1500 RPM has a cutting speed of \( 1500 \times \pi \times 0.01 = 47.12 \) m/min.

How to Read the Result

The linear speed you get is the speed of a point on the rim of the rotating object. If you attach that object to a vehicle (like a wheel), the vehicle’s forward speed equals this rim speed only if there is no slipping and the wheel is rolling without skidding. In reality, tire deformation and slip can cause the actual vehicle speed to be slightly lower (typically 1–5% depending on tire pressure and load).

For a pulley driving a belt, the belt speed is the same as the rim speed of the pulley, assuming no belt slip. For a gear, the pitch line speed (not the outer diameter) is used for meshing calculations, but the outer diameter speed is still useful for balancing and inertia estimates.

Common Mistakes

  • Using radius instead of diameter: The formula uses diameter. If you have radius, double it first.
  • Unit mismatch: If you enter diameter in centimeters, the speed will be in cm/s, not m/s. Always convert to consistent units (e.g., meters for m/s).
  • Forgetting the 60: RPM is per minute, but speed is usually per second. The 60 is essential.
  • Confusing angular speed with linear speed: RPM is a rotational measure; it does not tell you how fast the object moves in a straight line unless you know the diameter.
  • Using the wrong diameter for a tire: For a car tire, the loaded radius is slightly smaller than the unloaded radius due to the weight of the vehicle. Use the rolling circumference (often given by the tire manufacturer) for accurate vehicle speed.

Practical Examples

Here are a few real-world scenarios to illustrate the use of the formula:

  • Bicycle: A 700c wheel has a diameter of about 0.668 m (including tire). If you pedal at a cadence that gives 90 RPM of the wheel (after gearing), the speed is \( 90 \times \pi \times 0.668 / 60 = 3.15 \) m/s, or 11.3 km/h. This matches a typical slow commuting speed.
  • Angle grinder: A 125 mm disc (diameter 0.125 m) spins at 11,000 RPM. The rim speed is \( 11000 \times \pi \times 0.125 / 60 = 72.0 \) m/s, which is about 259 km/h. This high speed is why angle grinders are dangerous — the abrasive particles are moving extremely fast.
  • Wind turbine: A large turbine blade tip might be 60 m from the hub (diameter 120 m). If the rotor spins at 15 RPM, the tip speed is \( 15 \times \pi \times 120 / 60 = 94.2 \) m/s, which is over 300 km/h. That is why blade tips are designed to handle high stresses.

Limits of the Formula

This formula is purely kinematic — it does not account for forces, torque, power, or efficiency. It assumes the object is rigid and the speed at the rim is uniform. For flexible objects like tires, the effective rolling radius changes with speed and load. For very high speeds (approaching the speed of light), relativistic effects would matter, but that is far beyond any mechanical application. Also, the formula gives the instantaneous speed; if the RPM varies, the linear speed varies accordingly.

Frequently Asked Questions

What is the difference between RPM and linear speed? RPM (revolutions per minute) measures how many full rotations an object makes in one minute. Linear speed measures how far a point on the object travels in a given time (e.g., meters per second). They are related by the circumference: one revolution moves a point by the circumference distance.

How do I convert RPM to speed in km/h? Use the formula: speed (km/h) = (RPM × π × diameter in meters × 60) / 1000. Alternatively, calculate speed in m/s and multiply by 3.6. For example, 100 RPM with a 0.5 m diameter gives 2.62 m/s, which is 9.42 km/h.

Does the formula work for any rotating object? Yes, as long as you know the diameter of the circle at the point you are interested in. For a wheel, use the outer diameter of the tire. For a shaft, use the shaft diameter. For a gear, you might use the pitch diameter instead of the outer diameter for meshing speed.

Why is the speed at the center zero? The linear speed of a point at the center of rotation is zero because its distance from the axis is zero. The speed increases linearly with distance from the center, reaching a maximum at the outer edge. This is why the formula uses the full diameter.

What if I only know the radius? Simply double the radius to get the diameter, then use the formula. For example, a radius of 0.25 m gives a diameter of 0.5 m.

Is this the same as cutting speed in machining? Yes, cutting speed is the linear speed of the workpiece surface relative to the cutting tool. It is often given in m/min or SFPM. You can use the same formula but omit the division by 60 if you want m/min: cutting speed (m/min) = RPM × π × diameter (in meters).

Related

Formula used
in m | Rotational speed (RPM) | rpm | 100 | 0
in d | Diameter | m | 0.5 | 0
out v | Linear speed (m/s) | m/s | (m * pi * d) / 60 | 2
out vkmh | Speed (km/h) | km/h | v * 3.6 | 2
out vmih | Speed (mph) | mph | v * 2.2369362920544 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →