A log volume calculator estimates the usable wood volume in a log from its dimensions, typically the small-end diameter and length. You enter those two measurements and the calculator returns the volume in cubic meters or board feet, depending on the formula you choose. This is the standard way timber is measured for sale, transport, and milling planning.
Formula
The three most common log volume formulas are:
- Huber: V = (π/4) × Dm² × L, where Dm is the diameter at the middle of the log, L is the length, and V is the volume in cubic meters.
- Smalian: V = (L/2) × (A1 + A2), where A1 and A2 are the cross-sectional areas at the two ends (each π/4 × D²).
- Newton: V = (L/6) × (A1 + 4Am + A2), where Am is the cross-sectional area at mid-length.
All diameters are in centimeters, converted to meters (divide by 100) so the volume comes out in cubic meters. The small-end diameter is the one measured at the top (narrower) end of the log, excluding bark. The mid-diameter is measured halfway along the log, also excluding bark.
Worked Example
Using the default values: small-end diameter = 30 cm, length = 4 m, and Huber’s formula (mid-diameter = 28 cm).
- Convert the mid-diameter to meters: 28 cm ÷ 100 = 0.28 m.
- Compute the cross-sectional area: π/4 × (0.28)² = 0.785398 × 0.0784 = 0.061575 m².
- Multiply by length: 0.061575 × 4 = 0.2463 m³.
The calculator rounds to three decimals, giving 0.246 m³. For Smalian, you would use both end diameters: small end 30 cm (0.30 m) and large end (say 34 cm, not shown in defaults) – but the calculator uses the mid-diameter input for both Smalian and Newton. In the block, the mid-diameter field is used for the mid-diameter in Huber and Newton, and as the large-end diameter in Smalian (since only two diameters are entered). To use Smalian, set the formula to 2 and enter the large-end diameter in the mid-diameter field.
Assumptions
- Logs are assumed to be perfect cylinders or frustums (tapered cones) with circular cross-sections.
- Diameters are measured inside the bark; bark volume is not included.
- The formulas give the geometric volume of the wood, not the volume of usable lumber after sawing (which depends on saw kerf, defects, and sawing pattern).
- Huber’s formula assumes the mid-diameter represents the average cross-section; it is accurate for logs with gentle taper.
- Smalian’s formula tends to overestimate volume on logs with significant taper.
- Newton’s formula is the most accurate for irregularly tapered logs, but requires three diameter measurements.
How to Choose the Right Formula
In practice, the choice of formula depends on how many measurements you can take and the expected taper of the log.
- Huber is the most common in many countries because it requires only one diameter measurement at mid-length. It is accurate when the log is nearly cylindrical or has gentle, even taper.
- Smalian needs only the two end diameters, which are easy to measure on a felled log. It is often used for short logs, but it overestimates volume on long, tapering logs.
- Newton is the most accurate but requires three measurements: both ends and the middle. It is used when precision matters, such as for high-value timber or research.
For standing trees, you would estimate the diameter at breast height and use a different formula (e.g., a taper equation), but this calculator is for cut logs.
Common Mistakes and How to Avoid Them
- Using the large-end diameter instead of the small-end. For Huber and Smalian, the small-end diameter is critical; using the large end overestimates volume.
- Forgetting to exclude bark. Bark can add 5–10% to the diameter, leading to a significant overestimate. Always measure inside the bark.
- Mixing units. If you measure diameter in inches and length in feet, you must convert to centimeters and meters, or use a board-foot formula. This calculator expects cm and m.
- Rounding too early. Round only the final answer, not intermediate area calculations, to avoid accumulation of error.
- Assuming geometric volume equals merchantable volume. Defects like rot, knots, or crooks reduce usable volume; this calculator gives the gross wood volume.
Board Feet vs. Cubic Meters
In North America, timber is often measured in board feet, where 1 board foot = 1 ft × 1 ft × 1 in (144 cubic inches). To convert cubic meters to board feet, multiply by 423.776 (since 1 m³ = 35.3147 ft³ and 1 ft³ = 12 board feet, so 35.3147 × 12 = 423.776). However, log scaling rules (like the Doyle or Scribner rules) are not simple volume conversions; they incorporate saw kerf and waste. This calculator gives the geometric cubic volume, which is the basis for many international timber trades. If you need board feet, multiply the cubic meter result by 423.776, but be aware that actual lumber yield will be lower due to sawing losses.
Practical Applications
Log volume calculations are used in several contexts:
- Timber sales: Buyers and sellers agree on a price per cubic meter based on the calculated volume.
- Transport planning: Trucking capacity is often limited by volume as well as weight; knowing the volume helps estimate how many logs fit on a truck.
- Forest inventory: Estimating the volume of standing timber requires different methods, but after felling, log volume is measured directly.
- Sawmill efficiency: Mills use volume to plan cutting patterns and estimate lumber recovery.
In many regions, a government or industry standard (e.g., the Hoppus foot in the UK, or the JAS scale in Japan) is used, which may differ from the geometric formulas here. Always check local practice.
Limitations of the Formula
These formulas assume the log is a perfect geometric solid. Real logs have irregular shapes, swellings, and taper that varies along the length. The formulas also do not account for defects such as rot, insect damage, or cracks, which reduce the usable volume. For high-value logs, a manual scaling by an experienced grader is often preferred. Additionally, the small-end diameter is the standard measure because it correlates best with the volume of usable lumber, but it is not the only factor; the length and taper also matter. Finally, the density of the wood is not considered – volume is not weight. If you need weight, multiply the volume by the wood density (e.g., 600 kg/m³ for many hardwoods, but this varies widely).
Frequently Asked Questions
What is the difference between small-end and large-end diameter? The small-end diameter is the diameter of the log at its narrower (top) end, measured inside the bark. The large-end is the diameter at the butt. Because logs taper, the small end is the limiting factor for lumber yield, so it is used in most scaling rules.
Why does the calculator ask for mid-diameter even when I use Smalian? In this calculator, the mid-diameter field is reused as the second diameter for Smalian (the large-end). For Huber and Newton, it is the actual mid-diameter. For Smalian, enter the large-end diameter in that field. This keeps the input count low, but you must know which formula you are using.
Can I use this for standing trees? No, this calculator is for cut logs. For standing trees, you would measure diameter at breast height (DBH) and use a taper equation or volume table, which also requires tree height and species-specific factors.
How do I convert cubic meters to board feet? Multiply the cubic meters by 423.776. For example, 0.246 m³ × 423.776 = 104.2 board feet. However, actual lumber yield will be less due to sawing losses; the Doyle and Scribner rules account for that.
What is the most accurate formula? Newton’s formula is the most accurate for logs with irregular taper because it uses three cross-sections. Huber is a good compromise for most logs. Smalian is the least accurate on long, tapering logs.
Does bark count in the volume? No, the formulas assume diameters are measured inside the bark. Bark adds volume but is not merchantable, so it is excluded. Always measure after debarking or subtract bark thickness.
Related
Formula used
in d | Small-end diameter (cm) | cm | 30 | 0 | 200 in L | Log length (m) | m | 4 | 0.1 | 20 sel f | Formula | Huber=1, Smalian=2, Newton=3 | 1 in dm | Mid-diameter (cm) | cm | 28 | 0 | 200 out v | Volume (cubic meters) | m³ | (f==1 ? pi/4 * (d/100)^2 * L : f==2 ? L/2 * (pi/4 * (d/100)^2 + pi/4 * (dm/100)^2) : L/6 * (pi/4 * (d/100)^2 + 4*pi/4 * (dm/100)^2 + pi/4 * (d/100)^2)) | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality to g/L Converter & Formula29.220 g/L
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check