To go from a low concentration to a high concentration, you must either remove solvent or add more solute; dilution alone cannot do it. This calculator finds the final volume needed to concentrate a solution by removing solvent, based on its starting concentration and volume and the desired higher concentration.
Formula
For a process that removes solvent while retaining the solute, the amount of solute stays constant. The concentration–volume relationship is c1V1 = c2V2, so the final solution volume is V2 = c1V1 / c2. The calculator also reports the volume removed, Vr = V1 − V2.
- c1 is the starting concentration in mol/L.
- V1 is the starting solution volume in mL.
- c2 is the desired concentration in mol/L.
- V2 is the final solution volume in mL.
- Vr is the volume removed in mL.
The same volume unit is used on both sides of the equation, so millilitres cancel consistently. This calculation assumes c2 is greater than c1. The expression includes a validity check: if the target is not higher than the starting concentration, the calculator reports that it cannot compute this concentration-up procedure.
Worked Example
Use the calculator defaults: c1 = 0.1 mol/L, V1 = 100 mL, and c2 = 0.5 mol/L.
V2 = (0.1 mol/L × 100 mL) / (0.5 mol/L) = 10 mL.
Vr = 100 mL − 10 mL = 90 mL.
The result is a final volume of 10.00 mL, with 90.00 mL removed. The calculation preserves the amount of solute: 0.1 mol/L × 0.100 L = 0.010 mol, and 0.5 mol/L × 0.010 L = 0.010 mol.
Assumptions
- The solute is retained while solvent is removed; no solute is lost, added, or chemically changed.
- The stated concentrations are accurate and expressed in the same units.
- Volumes are treated as additive and concentration is uniform in the solution.
- This is arithmetic for study and lab planning, not a procedure for concentrating any particular material.
What “Low to High Concentration” Means
Concentration describes how much solute is present relative to a specified amount of solution or solvent. A solution becomes more concentrated when that ratio increases. There are two broad ways to achieve this: reduce the amount of solvent while keeping the solute, or add additional solute. They are not interchangeable in practice, even though both can raise concentration.
The familiar dilution equation, c1V1 = c2V2, is most often used to calculate a lower target concentration from a more concentrated stock. It also expresses conservation of solute and can be rearranged for concentration by solvent removal. In the latter case, the final volume must be smaller than the starting volume. For example, changing 0.1 mol/L in 100 mL to 0.5 mol/L requires a final volume of 20% of the initial volume, provided all solute remains in solution.
Choosing a Concentration Method
Use the calculation above when the intended operation is removal of solvent and the amount of solute will remain constant. It tells you the required final volume, not how to carry out evaporation, filtration, or any other physical operation. The appropriate method depends on the substance and the validated lab method.
If instead you plan to add solute, the starting amount of solute is not constant. For a simple solution with a known molar mass, the theoretical additional mass can be calculated from the difference in moles:
madded = (c2 − c1) × V × M
Here c values are in mol/L, V is the final solution volume in L, and M is molar mass in g/mol; the result is grams. This assumes the added substance dissolves completely and that the specified final volume is achieved. If adding solid changes the solution volume, using the starting volume as V can give an inaccurate result. Make the final volume the quantity specified by the method rather than assuming that adding a measured amount of solute leaves volume unchanged.
Common Errors and Limits
- Confusing solution volume with solvent volume: Concentration is defined against the solution volume here. A target final volume is not necessarily the volume of solvent to use or remove.
- Reversing the ratio: For concentration by solvent removal, a higher target gives a smaller final volume. If the computed final volume is larger than the starting volume, check whether the goal is actually dilution.
- Mixing units: Both concentrations must use the same unit, and both volumes must use the same unit. Convert before calculation if, for instance, one concentration is in mmol/L and the other in mol/L.
- Assuming solute is conserved when it is not: Precipitation, adsorption, degradation, leakage, or a chemical reaction can change the amount of dissolved solute. The simple equation does not account for those effects.
- Rounding too early: Keep extra digits through intermediate calculations and round only the final reported volume to a precision appropriate for the measurement.
There is also a physical limit: concentrating by removing solvent cannot produce a stable homogeneous solution beyond its solubility limit under the relevant conditions. Once solute precipitates or separates, the assumption that it remains dissolved no longer holds. A numerical result does not establish that the target concentration is physically attainable.
For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. This calculator does not specify operating conditions or determine whether a particular solution is safe to handle.
Frequently Asked Questions
Can you make a low-concentration solution more concentrated by dilution?
No. Dilution adds solvent and lowers concentration. To raise concentration, remove solvent while retaining solute, or add more solute.
How do I calculate the final volume for a higher concentration?
Use V2 = c1V1/c2. Use matching concentration units and matching volume units, and make sure the target concentration exceeds the starting concentration.
How much solvent must be removed?
Subtract the calculated final volume from the starting solution volume: Vr = V1 − V2. This is a theoretical volume difference, not an instruction for a particular lab operation.
Can I use this equation when adding solute?
Not by itself. Adding solute changes the amount of solute, so calculate the additional amount separately and account for the final solution volume and whether the solute dissolves completely.
What if the target concentration is lower than the starting concentration?
That is a dilution, not concentration by solvent removal. Use a dilution calculation instead; the required final volume will be greater than the starting volume when the solute amount stays constant.
Related
Formula used
in c1 | Starting concentration | mol/L | 0.1 | 0 in v1 | Starting solution volume | mL | 100 | 0 in c2 | Target concentration | mol/L | 0.5 | 0 out v2 | Final solution volume | mL | c1 * v1 / c2 | 2 out vr | Volume removed | mL | v1 - v2 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s