The mass of 28.09 g of glucose (C6H12O6) corresponds to 0.1559 moles of the compound, using the standard molar mass of 180.156 g/mol. This page calculates the molarity of a solution when you know the mass of glucose, its molar mass, and the final solution volume.
Formula
The molarity (c) of a solution is calculated as:
c = m / (mm × V)
where:
- m = mass of solute in grams (g)
- mm = molar mass of the solute in grams per mole (g/mol)
- V = final volume of the solution in liters (L) — note that the calculator input is in milliliters (mL), so it is divided by 1000 to convert to liters
For glucose, the molar mass is 180.156 g/mol (C: 6 × 12.011 + H: 12 × 1.008 + O: 6 × 15.999).
Worked Example
Using the calculator defaults (which are for sodium chloride, NaCl, not glucose):
- Input: m = 2.922 g of NaCl, mm = 58.44 g/mol, v = 250 mL.
- Convert volume to liters: 250 mL = 250 / 1000 = 0.250 L.
- Calculate moles of solute: 2.922 g / 58.44 g/mol = 0.05000 mol.
- Calculate molarity: 0.05000 mol / 0.250 L = 0.2000 mol/L.
The calculator returns c = 0.2000 mol/L (or 0.2 M) and cmm = 200.00 mM.
For the specific question in the title — 28.09 g of glucose — the calculation would be:
- Moles of glucose = 28.09 g / 180.156 g/mol = 0.1559 mol.
- If dissolved to a final volume of 1 L, the molarity would be 0.1559 M.
Assumptions
- The solute is pure and anhydrous.
- The final volume is used, not the volume of solvent added (i.e., you dissolve the solute and then add solvent to reach the final volume).
- The solution is at 25 °C (room temperature) — density changes with temperature are ignored for dilute solutions.
- The molar mass is the standard IUPAC value; for glucose, 180.156 g/mol.
When to Use This Calculator
This calculator is for preparing solutions in a laboratory, typically for chemistry, biology, or biochemistry experiments. You need to know the mass of the solute (weighed on a balance), its molar mass (from the formula or a label), and the desired final volume. The result tells you the concentration in moles per liter (molarity), which is the standard unit for many reactions and assays.
For example, if you need 250 mL of a 0.5 M glucose solution, you would enter 0.5 as the molarity (but this calculator works the other way — you enter mass and volume, and it gives concentration). To use it for preparation, you would adjust the mass until the output matches your target concentration.
How to Read the Result
The primary output is molarity (mol/L), often abbreviated as M. The secondary output is millimolar (mM), which is 1/1000 of a molar. For example, 0.1559 M is the same as 155.9 mM. In biological labs, mM is commonly used for glucose concentrations in media or buffers.
If you are making a solution, the molarity tells you how many moles of solute are in each liter of solution. To prepare a specific volume, you multiply the molarity by the volume in liters to get the moles needed, then multiply by the molar mass to get the mass to weigh out.
Common Mistakes and Misconceptions
- Using the wrong molar mass: Glucose monohydrate (C6H12O6·H2O) has a molar mass of 198.17 g/mol, not 180.16. Always check the formula on the bottle.
- Mixing up volume units: The calculator uses mL, but the formula requires liters. Forgetting to divide by 1000 gives a result that is 1000 times too large.
- Using solvent volume instead of final volume: If you add 250 mL of water to 2.922 g of NaCl, the final volume is slightly more than 250 mL because the solute occupies space. Always dissolve the solute in less solvent, then top up to the mark.
- Assuming 1 g/mL density for water: For dilute solutions, this is fine, but for concentrated solutions, the density changes and molarity is not equal to molality.
Limits of the Formula
The formula c = m / (mm × V) assumes the solute dissolves completely and the volume does not change upon mixing. For most salts and sugars in water, this is a good approximation at low concentrations. However, for very concentrated solutions, the volume may contract or expand, and the molarity will be slightly different from the calculated value. Also, temperature affects the volume of the solution, so molarity changes with temperature. For precise work, prepare the solution at the temperature at which it will be used.
Frequently Asked Questions
How many moles are in 28.09 g of glucose?
Divide the mass by the molar mass: 28.09 g / 180.156 g/mol = 0.1559 mol. This is the number of moles of glucose molecules in that sample.
What is the molarity of a 28.09 g glucose solution in 500 mL?
First, convert 500 mL to 0.5 L. Moles = 0.1559 mol. Molarity = 0.1559 mol / 0.5 L = 0.3118 M. So the concentration is 0.3118 mol/L.
Why is the molar mass of glucose 180.16 g/mol?
Glucose has the formula C6H12O6. Using atomic weights: carbon (12.011 × 6 = 72.066), hydrogen (1.008 × 12 = 12.096), oxygen (15.999 × 6 = 95.994). Sum = 72.066 + 12.096 + 95.994 = 180.156 g/mol. The value is often rounded to 180.16.
Can I use this calculator for any solute?
Yes, as long as you know the molar mass of the solute. The calculator is generic: enter the mass and molar mass, and it will give the molarity. For example, for NaCl, the molar mass is 58.44 g/mol; for sucrose, it is 342.3 g/mol.
What is the difference between molarity and molality?
Molarity (M) is moles of solute per liter of solution. Molality (m) is moles of solute per kilogram of solvent. Molality is temperature-independent because it uses mass, while molarity changes with temperature because volume changes. This calculator gives molarity.
How do I prepare a 1 M glucose solution?
Weigh out 180.156 g of glucose, dissolve in about 800 mL of distilled water, then add water to bring the final volume to exactly 1 L. Mix well. Always use a volumetric flask for accuracy.