This calculator works out the mass of copper sulphate (CuSO₄) needed to prepare a solution of a given molarity and volume. You enter the desired concentration, the final solution volume, and the molar mass of the copper sulphate form you are using (anhydrous, pentahydrate, etc.), and it returns the required mass in grams. The result is the mass of solute to weigh out, before dissolving and making up to the final volume.
Formula
The core relationship is the definition of molarity:
Molarity (mol/L) = Mass of solute (g) ÷ Molar mass (g/mol) ÷ Volume (L)
In symbols: c = m / (M × V), where:
- m = mass of copper sulphate in grams (g)
- M = molar mass of the specific copper sulphate form in grams per mole (g/mol)
- V = final solution volume in litres (L) – note the calculator takes mL and divides by 1000
- c = concentration in moles per litre (mol/L, also written M)
To find the mass directly, rearrange: m = c × M × V.
Worked Example
Using the calculator defaults: you want a 0.2000 mol/L solution of sodium chloride (NaCl, molar mass 58.44 g/mol) in a final volume of 250 mL.
- Convert volume to litres: 250 mL ÷ 1000 = 0.250 L
- Calculate moles needed: 0.2000 mol/L × 0.250 L = 0.05000 mol
- Calculate mass: 0.05000 mol × 58.44 g/mol = 2.922 g
The calculator returns 2.922 g, matching the manual calculation. The concentration check: 2.922 g ÷ 58.44 g/mol ÷ 0.250 L = 0.2000 mol/L (displayed as 0.2000).
Assumptions
- The solute is pure and dry (no absorbed water unless it is the hydrate form).
- The final volume is measured after dissolving and making up with solvent, not the volume of solvent added.
- Temperature is near 25 °C – molarity changes slightly with temperature because volume changes.
- Complete dissolution – no undissolved solid remains.
Copper Sulphate Forms and Molar Masses
Copper sulphate exists in several hydrated forms, and the molar mass you use must match the solid you actually weigh. The most common laboratory form is the pentahydrate, CuSO₄·5H₂O. The anhydrous form (CuSO₄) is a white or grey powder that readily absorbs water. The trihydrate (CuSO₄·3H₂O) is less common but appears in some industrial contexts.
- Anhydrous CuSO₄: molar mass = 159.61 g/mol (Cu 63.546 + S 32.06 + 4×O 15.999)
- Pentahydrate CuSO₄·5H₂O: molar mass = 249.69 g/mol (anhydrous + 5×18.015)
- Trihydrate CuSO₄·3H₂O: molar mass = 213.65 g/mol
If you prepare a 1.00 mol/L solution using the pentahydrate, you need 249.69 g per litre, not 159.61 g. Using the wrong molar mass is the single most common error in copper sulphate solution preparation.
How to Choose the Correct Molar Mass
Check the label on the reagent bottle. It will state whether the solid is anhydrous, pentahydrate, or another hydrate. If the label is missing, look at the appearance: the pentahydrate is bright blue crystalline; the anhydrous form is a pale grey-white powder. If you have a hydrate with an unknown number of water molecules, you can determine it by drying a sample in an oven at 150 °C for an hour and measuring the mass loss – the difference corresponds to the water of crystallisation.
For most school and university labs, the pentahydrate is the default. Always use the molar mass that matches the bottle, not a generic value from memory.
Common Mistakes and How to Avoid Them
- Using the anhydrous mass for the hydrate: This gives a solution about 36% more concentrated than intended. Always confirm the form.
- Adding solvent to the solute instead of making up to volume: If you add 250 mL of water to the solid, the final volume will be more than 250 mL, diluting the solution. Dissolve the solid in about 80% of the final volume, then top up to the mark.
- Ignoring temperature: Volumetric flasks are calibrated at a specific temperature (usually 20 °C). Preparing solutions at much higher or lower temperatures changes the volume slightly.
- Rounding intermediate values too early: Round only the final answer, not the moles or volume in between.
When to Use This Calculator
Use this calculator whenever you need to prepare a copper sulphate solution of a known molarity – for example, 0.1 M CuSO₄ for electrochemistry experiments, 0.5 M for protein assays (Biuret test), or 1.0 M for crystal growth. It also works for any other soluble salt, as long as you enter the correct molar mass.
The calculator is for planning and study purposes. In the lab, always follow your written method, the safety data sheet (SDS), and your supervisor’s instructions.
Safety and Handling
Copper sulphate is harmful if swallowed and can irritate skin and eyes. Wear gloves and safety glasses when handling the powder or solutions. Avoid inhaling dust – weigh in a fume hood if available. Wash hands after use. Dispose of copper sulphate solutions as hazardous chemical waste, not down the sink, unless your local regulations allow very dilute amounts.
Do not confuse copper sulphate with copper sulfate pentahydrate in terms of dose – the hydrate contains water that dilutes the copper content. For any biological or agricultural application, follow the specific product label and regulations.
Frequently Asked Questions
What is the molar mass of copper sulphate pentahydrate?
The molar mass of CuSO₄·5H₂O is 249.69 g/mol. This is the sum of the anhydrous salt (159.61 g/mol) plus five water molecules (5 × 18.015 g/mol = 90.08 g/mol). This is the value to use when weighing the blue crystalline form.
How do I make a 0.1 M copper sulphate solution?
For 1 litre of 0.1 M solution using the pentahydrate, weigh 24.97 g of CuSO₄·5H₂O. Dissolve in about 800 mL of distilled water, then make up to exactly 1 litre in a volumetric flask. For 500 mL, use half the mass (12.48 g).
Why does copper sulphate solution appear blue?
The blue colour comes from the hydrated copper(II) ion, [Cu(H₂O)₆]²⁺. The water molecules around the copper ion absorb light in the red-orange part of the spectrum and transmit blue. Anhydrous copper sulphate is white because it lacks these water ligands.
What is the difference between copper sulphate and copper sulfate?
They are the same compound. “Sulfate” is the IUPAC spelling; “sulphate” is the British/Commonwealth spelling. Both refer to CuSO₄. In chemistry, the term “copper sulphate” usually means the pentahydrate unless stated otherwise.
Can I use this calculator for other salts?
Yes. The formula c = m/(M×V) applies to any soluble compound. Just replace the molar mass with that of your salt. For example, for sodium chloride (NaCl, 58.44 g/mol), the calculator defaults already show the correct result.
What if I only have the anhydrous form but the recipe says pentahydrate?
You need to adjust the mass. Since the anhydrous form has a lower molar mass (159.61 vs 249.69 g/mol), you need less of it to get the same number of moles. Multiply the pentahydrate mass by the ratio 159.61/249.69 ≈ 0.639. For 24.97 g of pentahydrate, you would need about 15.96 g of anhydrous CuSO₄.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check