Measuring enthalpy change at A-level means using a calorimeter to track the temperature change of a known mass of water or solution, then converting that temperature change into an energy value using the formula q = mcΔT. You enter the mass of the substance being heated (usually water), its specific heat capacity, and the temperature change; the calculator below gives you the heat energy absorbed or released in joules, which you can then convert to an enthalpy change per mole of reactant.
Formula
The core relationship is q = m × c × ΔT, where:
- q = heat energy absorbed or released (in joules, J)
- m = mass of the substance being heated or cooled (in grams, g) – usually water or an aqueous solution
- c = specific heat capacity (in J/g·°C) – for water, 4.18 J/g·°C is the standard value used at A-level
- ΔT = temperature change (in °C or K, since a change of 1 °C equals a change of 1 K)
To get the enthalpy change per mole, divide q by the number of moles of the limiting reactant (n): ΔH = (q/1000) / n, giving the result in kJ/mol. The sign matters: if the temperature rises (exothermic reaction), ΔH is negative; if it falls (endothermic), ΔH is positive.
Worked Example
Using the default values from the calculator: 100 g of water, specific heat capacity 4.18 J/g·°C, temperature rise of 12.5 °C, and 0.050 mol of the limiting reactant.
- Calculate q: q = 100 g × 4.18 J/g·°C × 12.5 °C = 5225 J
- Convert to kJ: 5225 J ÷ 1000 = 5.225 kJ
- Divide by moles: ΔH = 5.225 kJ ÷ 0.050 mol = 104.5 kJ/mol
Since the temperature rose, the reaction is exothermic, so the enthalpy change is −104.5 kJ/mol. The calculator gives the same result when you round to one decimal place.
Assumptions
- The specific heat capacity of the solution is the same as pure water (4.18 J/g·°C).
- The density of the solution is 1.00 g/mL, so a volume in mL equals a mass in grams.
- No heat is lost to the surroundings (perfect insulation).
- The thermometer and container do not absorb any significant heat.
- The reaction goes to completion and the limiting reactant is fully consumed.
How to Measure Temperature Change Accurately
In a school or college lab, you typically use a polystyrene cup (a simple calorimeter) with a thermometer and a lid. The key is to measure the initial temperature and then the maximum (for exothermic) or minimum (for endothermic) temperature after mixing. But because the reaction starts immediately, you often miss the true starting temperature. The standard fix is to plot temperature against time and extrapolate back to the time of mixing. This corrects for heat loss to the surroundings during the reaction.
Steps for a typical neutralisation or displacement experiment:
- Measure a known volume of solution (e.g., 25.0 cm³ of 1.0 mol/dm³ acid) into the cup.
- Record its temperature every 30 seconds for a couple of minutes to establish a baseline.
- Add the second reagent (e.g., 25.0 cm³ of 1.0 mol/dm³ alkali) quickly, stir, and record the temperature every 30 seconds for several minutes.
- Plot temperature vs. time, draw the best-fit lines, and extrapolate to the mixing time to find the true ΔT.
- Use q = mcΔT, where m is the total mass of the solution (volume in cm³ ≈ mass in grams).
Common Mistakes and How to Avoid Them
- Using the wrong mass: For reactions in solution, the mass is the total volume of the mixed solution (assuming density 1 g/mL), not just the mass of the limiting reagent.
- Forgetting the sign: Exothermic reactions have negative ΔH; endothermic have positive ΔH. Always attach the sign based on the temperature change.
- Ignoring heat loss: Without extrapolation, the measured ΔT is too small, so the calculated ΔH is less exothermic (or less endothermic) than the true value.
- Mixing up units: q is in joules, but ΔH is in kJ/mol. Remember to divide by 1000.
- Using the wrong specific heat capacity: For solutions, 4.18 J/g·°C is the accepted value at A-level. For combustion experiments, you use the mass of water in the calorimeter, not the mass of the fuel.
Comparing Methods: Solution Calorimetry vs. Combustion Calorimetry
There are two main types of enthalpy measurements you will encounter:
- Solution calorimetry (e.g., neutralisation, displacement, dissolving): The reaction happens in a liquid, and you measure the temperature change of that liquid. Simple equipment (polystyrene cup) is fine because heat loss is relatively slow.
- Combustion calorimetry (e.g., burning ethanol or hexane): You burn a fuel and use the heat to warm a known mass of water in a metal can (a “flame calorimeter”). This is less accurate because a lot of heat escapes. A bomb calorimeter (constant volume) gives more accurate results but is rarely used at A-level.
For combustion, you need to know the mass of fuel burned (by weighing the spirit burner before and after), the mass of water, and the temperature rise of the water. The enthalpy change is then q divided by the moles of fuel burned.
Why Measured Values Differ from Theoretical Values
Your experimental ΔH will almost never match the data book value. The main reasons are:
- Heat loss to the surroundings – the biggest source of error.
- Incomplete combustion (for fuels) – some carbon is left as soot or carbon monoxide, releasing less energy.
- Heat absorbed by the container and thermometer – not accounted for in the simple formula.
- Evaporation of water or volatile liquids – absorbs heat and lowers the temperature rise.
- Reaction may not go to completion, or there may be side reactions.
These factors usually make exothermic values appear less negative than the true value, and endothermic values appear less positive.
Frequently Asked Questions
What is the difference between ΔH and q?
q is the heat energy transferred in a particular experiment (in joules). ΔH is the enthalpy change per mole of a specified substance (in kJ/mol). To convert, you divide q by the number of moles of the limiting reactant and adjust the sign according to whether the reaction is exothermic or endothermic.
Why do we use 4.18 J/g·°C for specific heat capacity?
That is the specific heat capacity of water. Since most reactions in A-level calorimetry involve aqueous solutions that are mostly water, we assume the solution has the same heat capacity. This is an approximation – concentrated solutions have slightly different values, but the error is small enough for school experiments.
How do I know which reactant is the limiting reactant?
Calculate the moles of each reactant using concentration × volume (in dm³) for solutions, or mass ÷ molar mass for solids. The one that gives the smallest number of moles is the limiting reactant – it is the one that is completely used up, so it determines the amount of energy released.
Why does my experimental value for enthalpy of combustion come out too low?
Because a lot of heat is lost to the air, the metal container, and the thermometer. Also, combustion is often incomplete, and some of the fuel evaporates without burning. These all mean less heat reaches the water, so the temperature rise (and hence ΔH) is smaller than the true value.
Do I need to convert °C to K when using q = mcΔT?
No, because you are using a temperature change, not an absolute temperature. A change of 1 °C is exactly the same as a change of 1 K, so the numerical value of ΔT is identical in both scales. Only when you use the ideal gas equation or thermodynamic tables do you need absolute temperature in kelvin.
What is the most accurate calorimeter?
A bomb calorimeter is the most accurate for combustion reactions because it operates at constant volume and minimises heat loss. For solution reactions, a well-insulated calorimeter with a lid and careful extrapolation of temperature gives good results. In all cases, the real check is the temperature reading – make sure your thermometer is calibrated and you stir consistently.
Follow your lab method, the safety data sheet (SDS) and your supervisor when performing any calorimetry experiment.
Related
Formula used
in m | Mass of water/solution | g | 100 | 0 in c | Specific heat capacity | J/g·°C | 4.18 | 0 in dt | Temperature change (ΔT) | °C | 12.5 | 0 in n | Moles of limiting reactant | mol | 0.050 | 0 out q | Heat energy (q) | J | m * c * dt | 1 out dh | Enthalpy change (ΔH) | kJ/mol | (q / 1000) / n | 1
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check