molecalculator

Moles & Molar Mass

Acetone Melting Point and Calculator

Calculator No. 01-2316 · Updated · Formula and assumptions shown below

Temperature -138.5 °F
Temperature
178.45 K
= Temperature + 273.15
Temperature
-94.7 °C
Set in the form below
You enter
Temperature (°C)
You get
Temperature (°F), Temperature (K)
Rounding
1 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Acetone melts at approximately −94.7 °C (−138.5 °F, or 178.5 K) at ordinary atmospheric pressure. This calculator converts a temperature between Celsius, Fahrenheit, and kelvin, so you can compare a measured value with acetone’s reference melting point.

Formula

The first result converts Celsius to Fahrenheit using °F = (°C × 9/5) + 32. The second converts Celsius to kelvin using K = °C + 273.15. Here, tc is temperature in degrees Celsius, tf is temperature in degrees Fahrenheit, and tk is temperature in kelvin. The input must be at or above absolute zero, −273.15 °C.

Worked Example

Using the default input, −94.7 °C:

  • Fahrenheit: (−94.7 × 9/5) + 32 = −170.46 + 32 = −138.46 °F, which rounds to −138.5 °F.
  • Kelvin: −94.7 + 273.15 = 178.45 K.

The conversion results express the reference melting temperature in other units; they do not predict a sample’s melting behavior.

Assumptions

  • The input temperature is expressed in degrees Celsius.
  • Conversions use the exact Celsius-to-kelvin offset, 273.15, and the standard Fahrenheit conversion factor, 9/5, with an offset of 32.
  • The reference value is approximate. A substance’s observed phase-change temperature can depend on pressure, purity, and measurement conditions.

What the melting point means

A melting point is the temperature at which solid and liquid forms of a substance are in equilibrium at a specified pressure. At about one atmosphere, pure acetone’s melting point is commonly reported as −94.7 °C. Reference sources may differ slightly in the last decimal place because of rounding and the conditions or measurement methods they report.

Acetone, also called propanone, has the formula C3H6O. It is a small organic molecule and a volatile liquid at ordinary room temperatures. Its low melting point means that cooling acetone to typical freezer temperatures does not normally turn it into a solid. For comparison, water freezes at 0 °C, far above acetone’s melting point.

The melting point is not the same as the boiling point. Acetone boils at about 56 °C at one atmosphere, so its normal liquid range extends from roughly −94.7 °C to 56 °C. Both phase-change temperatures refer to specified pressure conditions, not to an immutable property under every environment.

Why acetone melts at a low temperature

Melting occurs when thermal energy allows molecules in a solid’s ordered arrangement to move into a liquid state. The temperature at which this happens depends on how strongly molecules attract one another and how effectively they pack into a crystal.

Acetone molecules are polar: the carbonyl group, C=O, creates an uneven distribution of electrical charge. They attract each other through dipole–dipole interactions and dispersion forces. However, acetone molecules do not form the strong, extensive hydrogen-bond network that water molecules form with one another. Acetone can accept hydrogen bonds from suitable substances, but it has no O–H or N–H bond to donate one to another acetone molecule. Its molecular structure and intermolecular attractions are consistent with its low melting point relative to water.

This explanation is a useful qualitative comparison, not a way to calculate an exact melting point from a molecule’s structure alone. Crystal packing, molecular shape, and solid-state organization also matter.

Pressure, purity, and measured values

A quoted melting point is meaningful only alongside its conditions. Changing pressure can shift the temperature at which solid and liquid coexist. For ordinary reference comparisons, the reported acetone value is generally understood to be near atmospheric pressure; specialized high-pressure measurements need not match it exactly.

Impurities can also change observed phase behavior. A contaminated sample may begin melting over a range rather than at a sharp temperature, and its apparent onset may be lower than that of a pure material. This is why a single temperature from a handbook should not be treated as proof that an unknown sample is pure or correctly identified.

For a simple unit check, entering −94.7 °C gives approximately −138.5 °F and 178.45 K. The kelvin value is positive because the kelvin scale starts at absolute zero. Celsius and Fahrenheit values can be negative without indicating an impossible temperature; only values below −273.15 °C would violate the lower limit used by this calculator.

Common misconceptions and safety

One common misconception is that acetone freezes at the temperature of a household freezer. A typical freezer is far warmer than −94.7 °C, so it will not ordinarily solidify acetone. Another is that the reported melting point is also its boiling point: the two transitions occur at very different temperatures.

Acetone is highly flammable and evaporates readily. Its low melting point is not a reason to cool or handle it casually: vapor can ignite, and exposure can irritate the eyes and respiratory tract. Keep it away from flames, sparks, and heat, use suitable ventilation, and consult the safety data sheet (SDS) for handling and storage guidance. Do not use a domestic freezer or food refrigerator to store acetone; flammable vapor and ignition sources create serious hazards.

This page’s calculator is for temperature conversion and reference comparison only. It does not determine sample purity, prescribe a laboratory method, or replace appropriate chemical safety controls.

Frequently Asked Questions

What is acetone’s melting point in Fahrenheit?
Approximately −138.5 °F, equivalent to about −94.7 °C.

What is acetone’s melting point in kelvin?
Using −94.7 °C as the reference, the conversion is 178.45 K. Because the Celsius reference is approximate, this converted value is approximate too.

Does acetone freeze in a household freezer?
No, not under normal household-freezer conditions. Acetone’s melting point is much colder than the temperatures such freezers typically reach.

Is acetone’s melting point the same as its boiling point?
No. At about one atmosphere, acetone melts near −94.7 °C and boils near 56 °C.

Why might a reference give a slightly different melting point?
Sources may round differently or refer to different measurement conditions, pressure, or sample purity. The commonly cited value is approximately −94.7 °C.

Related

Formula used
in tc | Temperature | °C | -94.7 | -273.15
out tf | Temperature | °F | tc * 9 / 5 + 32 | 1
out tk | Temperature | K | tc + 273.15 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →