A mesh analysis calculator solves a linear electrical circuit by applying Kirchhoff’s Voltage Law (KVL) to each independent loop, or mesh, and then solving the resulting system of equations for the mesh currents. You enter the resistor values and voltage sources for each mesh, and the calculator returns the current in each loop, from which you can find branch currents and voltages. This page explains the method, shows a worked example, and answers common questions about when and how to use mesh analysis.
Formula
For a two-mesh circuit with resistors R1 in mesh 1, R2 shared between meshes, R3 in mesh 2, and voltage sources V1 and V2, the mesh-current equations are:
Mesh 1: (R1 + R2) i1 − R2 i2 = V1
Mesh 2: −R2 i1 + (R2 + R3) i2 = −V2
Here i1 and i2 are the mesh currents in amperes (A). The sign of V2 is negative because the source polarity opposes the assumed clockwise direction of i2. Solving these two linear equations gives the formulas used in the calculator. The first output, i1, is the headline result; i2 is the second mesh current.
Worked Example
Using the defaults: R1 = 10 Ω, R2 = 20 Ω, R3 = 30 Ω, V1 = 12 V, V2 = 6 V.
Step 1: Write the equations.
(10 + 20) i1 − 20 i2 = 12 → 30 i1 − 20 i2 = 12
−20 i1 + (20 + 30) i2 = −6 → −20 i1 + 50 i2 = −6
Step 2: Solve for i1 using the formula.
i1 = (12 × (20 + 30) − 6 × 20) / (10 × (20 + 30) + 20 × 30)
i1 = (12 × 50 − 120) / (500 + 600) = (600 − 120) / 1100 = 480 / 1100 = 0.436 A ≈ 0.436 A
Step 3: Solve for i2.
i2 = (6 × (10 + 20) − 12 × 20) / (1100) = (6 × 30 − 240) / 1100 = (180 − 240) / 1100 = −60 / 1100 = −0.0545 A ≈ −0.0545 A
The negative sign for i2 means the actual current flows opposite to the assumed clockwise direction.
Assumptions
- The circuit is planar, meaning no wires cross without a connection.
- All resistors are linear (Ohm’s law holds) and have constant values.
- Voltage sources are ideal (zero internal resistance).
- Current sources, if present, must be converted to equivalent voltage sources or handled with the supermesh technique, which this simple two-mesh calculator does not cover.
- The calculator solves only two independent meshes; larger circuits require a matrix solver.
How Mesh Analysis Works
Mesh analysis is a systematic way to reduce a circuit to a set of simultaneous equations. You assign a current to each mesh (a loop that contains no other loop inside it), then apply KVL: the sum of voltage rises equals the sum of voltage drops around any closed loop. For each resistor, the voltage drop is the current times the resistance, but when a resistor is shared by two meshes, the net current through it is the difference of the two mesh currents. That is why the equations have cross terms like −R2 i2 in the first equation. The method is particularly efficient for circuits with many loops but few nodes, compared to nodal analysis which uses Kirchhoff’s Current Law.
How to Choose the Right Calculator
This calculator handles the most common two-mesh circuit. Before using it, check that your circuit really has exactly two independent meshes. If you have three or more meshes, you need a matrix-based solver or a circuit simulator. Also confirm that your circuit is planar; if wires cross without connecting, mesh analysis still works, but you must redraw it as planar first. For circuits with current sources, you may need to use the supermesh approach, which combines two meshes into one equation. If your circuit has a dependent source, the equations become more complex and this simple calculator will not be accurate.
Common Mistakes and How to Avoid Them
- Sign errors with voltage sources: Always check the polarity. If the source’s positive terminal is encountered before the negative terminal when traversing the mesh in the assumed current direction, the voltage is added; otherwise it is subtracted. In the example, V2 is subtracted because its polarity opposes the clockwise current.
- Forgetting shared resistors: When a resistor lies between two meshes, its voltage drop is R × (i_mesh1 − i_mesh2), not R × i_mesh1. This is the most common error.
- Unit mix-ups: Keep resistances in ohms and voltages in volts; the current will be in amperes. If you use kilohms, convert to ohms first (1 kΩ = 1000 Ω).
- Assuming the sign of the answer is wrong: A negative mesh current is perfectly valid; it just means the actual current flows opposite to your assumed direction.
Limitations of Mesh Analysis
Mesh analysis only works for planar circuits. Non-planar circuits (like a bridge with a diagonal wire that cannot be redrawn flat) require nodal analysis. It also becomes tedious for large circuits because the number of equations equals the number of meshes. For circuits with many nodes, nodal analysis often yields fewer equations. Additionally, mesh analysis handles voltage sources easily but current sources require extra work (supermesh). For AC circuits, the same method applies but with complex impedances instead of resistances; this calculator is for DC resistive circuits only.
Comparison with Nodal Analysis
Nodal analysis uses Kirchhoff’s Current Law at each node and solves for node voltages. Mesh analysis uses KVL and solves for mesh currents. The choice depends on the circuit: if it has more meshes than nodes, nodal analysis is more efficient; if more nodes than meshes, mesh analysis is better. For example, a circuit with 4 nodes and 3 meshes is usually easier with mesh analysis. Both methods give the same results when applied correctly. Many textbooks recommend trying both and choosing the one that yields fewer equations.
Frequently Asked Questions
Can I use mesh analysis for circuits with current sources? Yes, but you need to handle them carefully. If a current source is on the outer edge of a mesh, that mesh current is simply equal to the source current. If the current source is shared between two meshes, you form a supermesh by combining the two meshes into one equation, then use the current source relation as an additional equation.
What is a supermesh? A supermesh is created when a current source lies between two meshes. You treat the two meshes as one larger loop for KVL, skipping the current source, and then add an equation that the difference of the two mesh currents equals the current source value.
Why is my calculated mesh current negative? A negative current simply means the actual current flows in the opposite direction to the one you assumed when drawing the mesh arrows. The magnitude is correct; just reverse the direction in your mind or on your diagram.
Does mesh analysis work for AC circuits? Yes, but you replace resistances with complex impedances (Z) and voltage sources with phasors. The equations are the same, but the arithmetic involves complex numbers. This calculator is for DC resistive circuits only.
What if my circuit has more than two meshes? You need to solve a system of three or more equations. You can use a general linear equation solver or a circuit simulator. The principle is the same, but the algebra grows quickly.
How do I find branch currents from mesh currents? For a resistor shared by two meshes, the branch current is the difference of the two mesh currents (i1 − i2). For a resistor in only one mesh, the branch current is simply that mesh current. Use the sign to determine direction.
Practical Tips for Using This Calculator
- Draw your circuit and label each mesh with a clockwise arrow (or any consistent direction).
- Identify which resistors are shared between meshes and which belong to only one mesh.
- Enter the resistance values in ohms. If your resistor is marked in kilohms, multiply by 1000 first.
- Enter voltage source values with the correct sign: positive if the source’s positive terminal is encountered first when moving in the mesh current direction, negative otherwise.
- After getting the mesh currents, verify by checking that KVL holds in each mesh with the calculated currents.
Always double-check your circuit topology and sign conventions. For lab work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Related
Formula used
in r1 | Resistor R1 (mesh 1) | Ω | 10 | 0.001 in r2 | Resistor R2 (shared) | Ω | 20 | 0.001 in r3 | Resistor R3 (mesh 2) | Ω | 30 | 0.001 in v1 | Voltage source V1 (mesh 1) | V | 12 | -1000 in v2 | Voltage source V2 (mesh 2) | V | 6 | -1000 out i1 | Mesh current i1 | A | (v1 * (r2 + r3) - v2 * r2) / (r1 * (r2 + r3) + r2 * r3) | 3 out i2 | Mesh current i2 | A | (v2 * (r1 + r2) - v1 * r2) / (r1 * (r2 + r3) + r2 * r3) | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- QPP Calculator Canada: How It Works & How to Use It
- PPP Calculator World Bank: How It Works & How to Use It2,000.00
- PPP Calculator: India vs USA Cost Comparison1,000.00 USD
- PPP Calculator USD to INR: How It Works2,335 INR
- PPP Calculator India vs UK: Real Cost Comparison103.63 GBP
- PPP Calculator India vs Dubai: Real Cost Comparison8,954.58 AED