molecalculator

Moles & Molar Mass

Cubic Meters per Hour to Liters per Minute

Calculator No. 01-6477 · Updated · Formula and assumptions shown below

Flow rate 16.667 L/min
Flow rate
0.000278 m³/s
= Flow rate ÷ 3600
Flow rate
1 m³/h
Set in the form below
You enter
Flow rate (m³/h)
You get
Flow rate (L/min), Flow rate (m³/s)
Rounding
3 dp · 6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To convert cubic meters per hour (m³/h) to liters per minute (L/min), multiply the flow rate by 16.6666667. This calculator takes a rate in m³/h and returns the equivalent rate in L/min, with the conversion factor shown so you can check the result.

Formula

The conversion formula is:

Flow in L/min = flow in m³/h × 1000 L/m³ ÷ 60 min/h

In symbols, r = q × 1000 ÷ 60, where q is the input flow rate in cubic meters per hour and r is the equivalent flow rate in liters per minute. One cubic meter contains exactly 1,000 liters, and one hour contains 60 minutes. The second output, s, is the same rate expressed in cubic meters per second: s = q ÷ 3,600, since an hour has 3,600 seconds.

Worked Example

Using the calculator’s default input, q = 1 m³/h:

  1. Convert cubic meters to liters: 1 m³/h × 1,000 L/m³ = 1,000 L/h.
  2. Convert hours to minutes: 1,000 L/h ÷ 60 min/h = 16.6666667 L/min.
  3. Rounded to the calculator’s three decimal places, the result is 16.667 L/min.

The additional output is 1 ÷ 3,600 = 0.000277778 m³/s, displayed to six decimal places as 0.000278 m³/s. These are equivalent descriptions of the same volumetric flow rate.

Assumptions

  • The input is a volumetric flow rate, not a volume or a mass-flow rate.
  • The units are exactly m³/h for the input and L/min for the main result.
  • The conversion is a unit conversion only; it assumes no change in the flow being described.

How the Conversion Works

A cubic meter is a volume: it is the space in a cube whose sides are each one meter long. A liter is one-thousandth of a cubic meter, so 1 m³ = 1,000 L. A flow rate combines volume and time. Converting m³/h to L/min therefore requires changing both parts of the unit: multiply by 1,000 to change cubic meters to liters, then divide by 60 to change “per hour” to “per minute.”

The combined multiplier is 1,000 ÷ 60 = 50/3, or 16.666666… . Thus, an input of 2 m³/h is equivalent to 33.333 L/min, while 0.3 m³/h is equivalent to 5 L/min. The reverse conversion is also useful: divide a value in L/min by 16.6666667, or multiply it by 0.06, to get m³/h.

Examples at Common Flow Rates

  • 0.06 m³/h = 1 L/min. This is a convenient check because 0.06 × 1,000 ÷ 60 equals 1.
  • 0.5 m³/h = 8.333 L/min. The result is a little over eight liters each minute.
  • 3 m³/h = 50 L/min. The factors combine neatly: 3,000 liters per hour divided by 60 minutes per hour.
  • 12 m³/h = 200 L/min. This can also be read as 12,000 liters passing in an hour.

These examples describe a steady rate. If the flow changes over time, the total volume cannot be found from a single rate unless that rate represents the relevant interval, such as a constant flow or a suitable average.

When to Use This Conversion

This conversion is useful when equipment specifications, measurements, or calculations use different flow-rate units. For example, one document might state a ventilation or water-flow rate in m³/h while a calculation sheet uses L/min. Converting the units makes the figures comparable, but it does not establish that equipment is suitable or that a measured system achieves its stated performance.

Keep volumetric flow distinct from mass flow. A value in kg/h or g/s describes mass passing per unit time, not volume. Converting mass flow into volume flow requires the fluid’s density under the relevant conditions, using volume flow = mass flow ÷ density. Density can vary with substance, temperature, pressure, and composition, so the simple multiplier in this calculator cannot convert mass-flow units.

Common Mistakes and Limits

  • Changing only the volume unit: multiplying by 1,000 gives L/h, not L/min. You must also divide by 60.
  • Using the reverse factor: to go from m³/h to L/min, multiply by about 16.667. To go from L/min to m³/h, multiply by 0.06.
  • Rounding too early: retain the full conversion factor for intermediate calculations, then round the final value to a precision appropriate to the measurement.
  • Confusing flow with accumulated volume: m³/h and L/min are rates. A total volume requires multiplying a rate by the elapsed time, with compatible units.

The arithmetic is exact when using 1 m³ = 1,000 L and 1 h = 60 min. In practice, the displayed answer should not imply more precision than the original measurement. For instance, a flow reading reported as 2 m³/h may have limited measurement precision even though its converted value can be calculated to many decimal places.

Frequently Asked Questions

How many liters per minute are in 1 m³/h?
1 m³/h equals 16.666666… L/min, usually written as 16.67 L/min or 16.667 L/min depending on the required precision.

What is the quick formula for m³/h to L/min?
Multiply the m³/h value by 16.6666667. Equivalently, multiply by 1,000 and divide by 60.

How do I convert L/min back to m³/h?
Multiply the L/min value by 0.06, or divide it by 16.6666667. For example, 50 L/min × 0.06 = 3 m³/h.

Does this conversion depend on the liquid or gas?
No. Converting between these two volumetric flow units uses only the definitions of cubic meters, liters, hours, and minutes. The fluid’s identity matters if converting between volume flow and mass flow, or when interpreting actual operating conditions.

Can I convert a total number of cubic meters to L/min?
Not from volume alone. You also need the time interval over which that volume flows. Divide the total volume by the elapsed time to obtain a rate, then convert the rate into L/min.

Related

Formula used
in q | Flow rate | m³/h | 1 | 0
out r | Flow rate | L/min | q * 1000 / 60 | 3
out s | Flow rate | m³/s | q / 3600 | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →