molecalculator

Moles & Molar Mass

Mh to H Conversion: Millihenry to Henry

Calculator No. 01-10459 · Updated · Formula and assumptions shown below

Inductance in henries 0.0470 H
Inductance in microhenries
47,000.00 µH
= Inductance in millihenries × 1000
Inductance in millihenries
47 mH
Set in the form below
You enter
Inductance in millihenries (mH)
You get
Inductance in henries (H), Inductance in microhenries (µH)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

One millihenry (mH) equals 0.001 henry (H), so to convert mH to H you divide the number of millihenries by 1000. For example, 47 mH = 0.047 H. This conversion is essential whenever you work with inductor values in circuit calculations, because most component markings and datasheets list inductance in millihenries or microhenries, while many formulas require henries.

Formula

The conversion is a simple power-of-ten scaling:

H = mH ÷ 1000

where:

  • H = inductance in henries (H)
  • mH = inductance in millihenries (mH)

Since the prefix “milli-” means one-thousandth, 1 mH = 1 × 10−3 H. Conversely, 1 H = 1000 mH. The same logic applies to microhenries: 1 µH = 1 × 10−6 H, so 1 mH = 1000 µH.

Worked Example

Using the default value of 47 mH from the calculator:

  1. Start with the inductance: 47 mH.
  2. Divide by 1000: 47 ÷ 1000 = 0.047 H.
  3. To express in microhenries: 47 × 1000 = 47000 µH.

The calculator returns 0.0470 H and 47000 µH, matching the manual calculation.

Assumptions

  • The conversion is exact; no physical assumptions about the inductor are needed.
  • Standard SI prefixes apply: milli = 10−3, micro = 10−6.
  • The calculator assumes you are entering a positive inductance value; negative inductance has no physical meaning for a passive component.

Why Inductance Units Matter

Inductors are used in filters, transformers, power supplies, and tuned circuits. Their values span a huge range: a small RF choke might be 1 µH, a power-supply filter inductor might be 10 mH, and a large audio crossover coil could be 50 mH or more. When you calculate resonant frequency (f = 1 / (2π√(LC))) or inductive reactance (XL = 2πfL), the inductance must be in henries for the result to come out in hertz or ohms respectively. If you plug in 47 mH instead of 0.047 H, your answer will be off by a factor of 1000, which could make a filter design useless.

Common Conversion Mistakes

  • Dividing instead of multiplying when going from mH to µH. Remember: smaller prefix → larger number. mH to µH multiplies by 1000; mH to H divides by 1000.
  • Confusing millihenries with microhenries on component markings. A coil stamped “470” on a small surface-mount package might be 47 µH (coded as 470) or 47 mH depending on the marking scheme. Always check the datasheet.
  • Forgetting that the henry is a large unit. Most practical inductors are in the millihenry or microhenry range, so a result like 0.000047 H is normal and should not be treated as an error.
  • Using mH in formulas that expect H without converting. This is the most common error in student lab reports and hobbyist projects.

How to Choose the Right Unit

When you read an inductor value, look at the prefix on the label or datasheet. If it says “mH,” keep it as millihenries for comparison with other parts, but convert to henries before doing any calculation that uses the inductance in a formula. If you are ordering parts, the unit matters: a 10 mH inductor is 1000 times larger than a 10 µH inductor, and they are physically very different components. For circuit simulation software, check the unit expected by the symbol — most SPICE programs use henries by default, so you must enter 0.047 rather than 47.

Related Inductance Conversions

Beyond mH to H, you may need these common conversions:

  • µH to mH: divide by 1000 (e.g., 4700 µH = 4.7 mH).
  • H to mH: multiply by 1000 (e.g., 0.1 H = 100 mH).
  • nH to µH: divide by 1000 (e.g., 1000 nH = 1 µH).

The pattern is always the same: move the decimal point three places for each prefix step. Milli (10−3), micro (10−6), and nano (10−9) are each a factor of 1000 apart.

Practical Example: Resonant Frequency

Suppose you have a 47 mH inductor and a 10 nF capacitor. To find the resonant frequency:

  1. Convert 47 mH to H: 47 ÷ 1000 = 0.047 H.
  2. Convert 10 nF to F: 10 × 10−9 = 1 × 10−8 F.
  3. Calculate LC: 0.047 × 1 × 10−8 = 4.7 × 10−10.
  4. Take the square root: √(4.7 × 10−10) ≈ 2.168 × 10−5.
  5. Frequency = 1 / (2π × 2.168 × 10−5) ≈ 7340 Hz.

If you had forgotten to convert and used 47 H, the frequency would come out as about 232 Hz — a completely different circuit behavior. This is why the conversion step is not optional.

Frequently Asked Questions

How do I convert 100 mH to H?

Divide 100 by 1000, giving 0.1 H. This is a common value for audio crossover inductors and small power-supply chokes.

Is 1 mH equal to 1000 µH?

Yes. The prefix “milli” means 10−3 and “micro” means 10−6, so one millihenry is exactly 1000 microhenries. A 4.7 mH inductor is the same as 4700 µH.

Why do some inductors have values in henries?

Large inductors, such as those used in high-power filters or energy-storage applications, can have values in the range of 1 to 10 H. These are physically large components with many turns of wire, often around a ferrite or iron core.

Can I use mH directly in the formula for inductive reactance?

No. The formula XL = 2πfL requires L in henries. If you use millihenries, the reactance will be 1000 times too large. Always convert to H first.

How do I read an inductor marked “470”?

It depends on the marking system. On many surface-mount inductors, a three-digit code is in microhenries: “470” means 47 µH (the third digit is the number of zeros). However, some manufacturers use “R” for a decimal point (e.g., “4R7” = 4.7 µH). Always check the datasheet for the specific part.

What is the difference between mH and MH?

mH (lowercase m) is millihenry, one-thousandth of a henry. MH (uppercase M) is not a standard SI prefix for inductance; megahenry would be MH, but such values are essentially never used. In practice, you will only see mH, µH, and nH.

Related

Formula used
in mh | Inductance in millihenries | mH | 47 | 0
out h | Inductance in henries | H | mh / 1000 | 4
out uh | Inductance in microhenries | µH | mh * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →