molecalculator

Moles & Molar Mass

Mixed Air Formula: Calculate Supply Air Temp

Calculator No. 01-8125 · Updated · Formula and assumptions shown below

Mixed air temperature 26.75 °C
Total airflow
2.00 m³/s
= Outdoor airflow + Return airflow
Outdoor air fraction
25.0 %
= (Outdoor airflow ÷ (Outdoor airflow + Return airflow)) × 100
Outdoor airflow
0.5 m³/s
Set in the form below
You enter
Outdoor airflow (m³/s), Outdoor air temperature (°C), Return airflow (m³/s), Return air temperature (°C)
You get
Mixed air temperature (°C), Total airflow (m³/s), Outdoor air fraction (%)
Rounding
2 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The mixed air formula calculates the temperature (and often humidity) of air after two or more airstreams combine, typically outdoor air and return air in an HVAC system. You enter the temperature and airflow rate of each airstream, and the calculator returns the resulting mixed air temperature. This is essential for sizing coils, predicting freezing risks, and designing economizer controls.

Formula

The mixed air temperature is the airflow-weighted average of the individual airstream temperatures:

Tmixed = (Q1 × T1 + Q2 × T2) / (Q1 + Q2)

Where:

  • Tmixed = mixed air temperature (°C)
  • Q1, Q2 = airflow rates of each stream (m³/s, L/s, or CFM – as long as they share the same unit)
  • T1, T2 = dry-bulb temperatures of each stream (°C or °F, but consistent)

For more than two streams, extend the pattern: sum of (Q × T) for all streams divided by the sum of all Q.

For mixed air enthalpy (used in load calculations), you must use the same formula but with enthalpy values (kJ/kg) instead of temperature, because enthalpy accounts for moisture. The simple temperature formula above works only for sensible heat (no condensation or evaporation).

Worked Example

Using the calculator defaults: outdoor air at 35 °C with 0.5 m³/s, return air at 24 °C with 1.5 m³/s.

  1. Multiply each flow by its temperature: 0.5 × 35 = 17.5; 1.5 × 24 = 36.0
  2. Add the products: 17.5 + 36.0 = 53.5
  3. Add the flows: 0.5 + 1.5 = 2.0 m³/s
  4. Divide: 53.5 / 2.0 = 26.75 °C

The calculator shows 26.75 °C (rounded to 26.75). The outdoor air fraction is (0.5 / 2.0) × 100 = 25%.

Assumptions

  • Air is an ideal gas with constant specific heat over the temperature range.
  • No heat transfer to or from the duct walls (adiabatic mixing).
  • No moisture condensation or evaporation during mixing (sensible only).
  • Airflows are measured at the same density – in practice, use mass flow or standard airflow (e.g., standard m³/s) for accuracy.

Why the Mixed Air Temperature Matters

HVAC engineers use the mixed air temperature to:

  • Size cooling coils – the coil must handle the mixed air condition, not just outdoor air. A 25% outdoor air fraction at 35 °C gives 26.75 °C, which is much easier to cool than 35 °C.
  • Prevent freezing – in winter, mixing warm return air with freezing outdoor air can drop the mixed temperature below 0 °C, risking coil freeze-up. Knowing the exact mixed temperature lets you add preheat or adjust the outdoor air damper.
  • Check economizer operation – an economizer uses outdoor air for free cooling when the outdoor air enthalpy is below return air enthalpy. The mixed air temperature helps decide when to switch.
  • Balance ventilation rates – building codes require minimum outdoor air, but too much increases energy use. The formula shows how much the outdoor air fraction affects supply temperature.

How to Choose the Right Airflow Units

The formula works with any consistent airflow unit: m³/s, L/s, CFM, or m³/h. The calculator uses m³/s, but you can convert before entering:

  • 1 m³/s = 1000 L/s = 2118.88 CFM = 3600 m³/h
  • If you have CFM, divide by 2118.88 to get m³/s.
  • If you have L/s, divide by 1000 to get m³/s.

Be careful with temperatures: use the same scale for all streams. The calculator uses °C, but you can convert °F to °C with (°F – 32) × 5/9.

Common Mistakes and Misconceptions

Mistake 1: Using volume flow instead of mass flow. The formula assumes equal air density. At extreme temperatures (e.g., -20 °C vs 40 °C), density differs by ~20%, causing errors. For precise work, use mass flow (kg/s) or correct to standard conditions.

Mistake 2: Averaging temperatures without weighting. A simple average (35+24)/2 = 29.5 °C is wrong unless both flows are equal. Always weight by airflow.

Mistake 3: Ignoring humidity. The temperature formula gives the dry-bulb mixed temperature, but the actual enthalpy (heat content) is not a simple weighted average of dry-bulb temperatures if the humidity ratios differ. For psychrometric calculations, use enthalpy or a psychrometric chart.

Misconception: The mixed air temperature is the supply temperature. Actually, the mixed air goes through filters, coils, and fans, which add heat (fan heat) or remove it (coil). The mixed air temperature is the condition entering the coil, not leaving it.

When to Use the Enthalpy Version

For cooling coil load calculations, you need the mixed air enthalpy, not just temperature. The formula becomes:

hmixed = (Q1 × h1 + Q2 × h2) / (Q1 + Q2)

Where h is specific enthalpy (kJ/kg dry air). You can get h from a psychrometric chart or formula using temperature and relative humidity. This is essential when outdoor air is hot and humid – the enthalpy can be much higher than the temperature suggests.

For example, 35 °C at 50% RH has an enthalpy of about 82 kJ/kg, while 24 °C at 50% RH has about 48 kJ/kg. The weighted enthalpy (25% outdoor) would be 0.25×82 + 0.75×48 = 56.5 kJ/kg, which corresponds to a higher effective cooling load than the simple temperature average suggests.

Frequently Asked Questions

What is the mixed air formula for three or more airstreams?

Extend the same pattern: Tmixed = (Q1T1 + Q2T2 + Q3T3) / (Q1+Q2+Q3). For example, if you have 0.2 m³/s at 10 °C, 0.3 m³/s at 20 °C, and 0.5 m³/s at 30 °C, the mixed temperature is (0.2×10 + 0.3×20 + 0.5×30) / (1.0) = 2+6+15 = 23 °C.

Does the mixed air formula work with CFM and Fahrenheit?

Yes, as long as you use the same units for all streams. The formula is unit-agnostic. For example, 200 CFM at 95 °F mixed with 800 CFM at 75 °F gives (200×95 + 800×75) / 1000 = (19000 + 60000) / 1000 = 79 °F. Just keep both temperature and flow units consistent.

How do I find the outdoor air fraction from the mixed air temperature?

Rearrange the formula: Outdoor fraction = (Tmixed – Treturn) / (Toutdoor – Treturn). For example, if mixed = 26.75 °C, return = 24 °C, outdoor = 35 °C, then (26.75 – 24) / (35 – 24) = 2.75 / 11 = 0.25, or 25%. This is useful for verifying damper positions.

Why does the mixed air temperature not match what I measure in the duct?

Real systems have heat gain or loss from duct walls, fan heat, and stratification (incomplete mixing). Also, temperature sensors may be placed too close to the mixing point. The formula gives the theoretical adiabatic mixed temperature; actual readings often differ by 1–3 °C. For accurate control, place sensors downstream of a mixing baffle or use multiple sensors.

Can I use this formula for mixing air with different humidities?

For dry-bulb temperature, yes, but the result is only the sensible temperature. If you need relative humidity or dew point of the mixture, you must use a psychrometric chart or calculate humidity ratio first. The mixed humidity ratio is the weighted average of the humidity ratios, not the relative humidities.

Related

Formula used
in m | Outdoor airflow | m³/s | 0.5 | 0
in t | Outdoor air temperature | °C | 35 | -273.15
in r | Return airflow | m³/s | 1.5 | 0
in tr | Return air temperature | °C | 24 | -273.15
out tm | Mixed air temperature | °C | (m*t + r*tr) / (m + r) | 2
out q | Total airflow | m³/s | m + r | 2
out op | Outdoor air fraction | % | (m / (m + r)) * 100 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →