An Mr, or relative molecular mass, does not by itself determine a substance’s volume: you also need its amount and, for a gas, the temperature and pressure. This calculator estimates the volume of an ideal gas from its Mr, mass, temperature, and pressure; it returns volume in litres and the corresponding amount in moles.
Formula
The calculation combines the definition of amount of substance with the ideal gas law:
- Amount: n = m / Mr
- Ideal gas law: V = nRT / P
- Combined formula used here: V (L) = (m / Mr) × 8.31446261815324 × (t + 273.15) / P
Here, m is sample mass in grams, Mr is relative molecular mass entered numerically in g/mol (the same numerical value as molar mass in g/mol), n is amount in mol, t is temperature in °C, T is absolute temperature in K, P is absolute pressure in kPa, and V is volume in litres. The gas constant is R = 8.31446261815324 J/(mol·K). Since 1 kPa·L = 1 J, this value of R works directly when pressure is in kPa and volume is in litres. The conversion from Celsius to kelvin is T = t + 273.15.
Mr is a ratio and is technically dimensionless. In the formula, its numerical value is used as the molar mass in g/mol, so dividing grams by g/mol gives moles. Use the Mr of the actual molecular formula, not a mass in atomic mass units entered as a different unit or a value for a different chemical form.
Worked Example
For 44 g of carbon dioxide, use Mr = 44.01, temperature 25 °C, and absolute pressure 101.325 kPa—the calculator’s default values.
- Find amount: n = 44 g / 44.01 g/mol = 0.99977 mol.
- Convert temperature: T = 25 + 273.15 = 298.15 K.
- Substitute into the gas equation: V = 0.99977 × 8.31446261815324 × 298.15 / 101.325 = 24.465 L.
Rounded to the calculator’s three decimal places, the estimated ideal-gas volume is 24.465 L. The amount output is 1.0000 mol when rounded to four decimal places. Small differences in a displayed final digit can arise if intermediate values are rounded before the full calculation.
Assumptions
- The sample is a gas that behaves ideally at the entered temperature and pressure.
- Pressure is absolute pressure, not gauge pressure.
- The sample’s mass and entered Mr refer to the same pure molecular substance.
- The gas constant and unit conversion are applied as stated: kPa, litres, kelvin, and grams per mole.
What “Mr Reg Volume Calculator” Means
The phrase “Mr reg volume calculator” is ambiguous. In chemistry, Mr usually means relative molecular mass; “reg” may be shorthand for regular or a typo for a different term. There is no single standard chemical formula called “Mr reg volume.” This page interprets the query as asking how to find a gas volume when Mr and sample mass are known, while also making clear which extra conditions are needed.
If “Mr” instead refers to a person, model, or another subject, this chemistry calculation will not apply. In a chemistry problem, check whether the question gives a gas, a liquid, or a solid, and whether it asks for molar volume, solution volume, or volume of a measured sample. Those are different quantities and may need different data.
When This Calculator Is Useful
Use it for study problems that provide the mass of a gaseous compound and ask for its theoretical volume at specified conditions. For example, a problem might give the mass of a small sample of a gas along with room temperature and atmospheric pressure. The calculation first converts the mass into moles using Mr, then uses temperature and pressure to estimate how much space that amount occupies.
It can also help compare the same amount of gas under different conditions. At fixed amount, increasing absolute temperature increases ideal-gas volume; increasing absolute pressure decreases it. If the question supplies amount directly in moles rather than mass, the mass and Mr route is unnecessary: use V = nRT/P directly.
This is not a calculator for the volume of a liquid or solid based on Mr. A condensed substance’s volume generally requires density, or other material-specific information. Nor does Mr alone reveal a gas volume: two samples with the same Mr can occupy different volumes if their masses, temperatures, or pressures differ.
Choosing Correct Inputs and Avoiding Errors
- Use absolute pressure. A pressure gauge reports pressure relative to the surrounding atmosphere. For a gauge reading, add local atmospheric pressure to obtain absolute pressure before using the gas law. Do not enter a negative or zero pressure.
- Enter temperature in Celsius. The calculator converts it to kelvin by adding 273.15. Do not enter a kelvin temperature into the Celsius field. Temperatures below absolute zero are impossible.
- Check Mr carefully. For CO₂, for example, the approximate calculation is 12.011 + 2 × 15.999 = 44.009 g/mol, commonly represented as 44.01 g/mol. Use a value appropriate to the formula and atomic weights required by the problem.
- Keep units consistent. Enter mass in grams, pressure in kPa, and Mr in g/mol. Convert other units before entering them; mixing bar, atmospheres, pascals, or kilograms with the defaults changes the result.
- Round at the end. Extra digits in intermediate calculations reduce rounding error. The displayed precision is not a claim that the measured mass, temperature, or pressure is exact.
Limits and Real-Gas Effects
The ideal gas law is an approximation. Many gases behave close to ideally at modest pressures and temperatures well above their condensation point, but deviations become more important at high pressure and near a gas’s condensation or critical conditions. In those cases, a real-gas equation or a tabulated compressibility factor may be needed. This calculator does not estimate those corrections, condensation, mixtures, or changes in chemical composition.
Its answer is a calculated gas volume under the specified conditions, not necessarily the volume a real sample will occupy in an apparatus. Container shape, leaks, temperature gradients, and measurement technique are outside the equation. For laboratory work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Frequently Asked Questions
Can I calculate volume from Mr alone?
No. Mr gives the mass per mole numerically, but you also need sample mass or amount, plus temperature and pressure to calculate a gas volume.
Is Mr the same as molar mass?
Mr is relative molecular mass and is dimensionless. Its numerical value is equal to molar mass expressed in g/mol for the same molecular formula. The calculator uses that numerical value in g/mol.
Why does the calculator ask for temperature and pressure?
A gas’s volume depends on both. The ideal gas law relates volume to amount and absolute temperature and pressure; the same number of moles does not have one fixed volume under all conditions.
Can I use this for a liquid or solid?
Not directly. For liquids and solids, volume usually depends on density and the material’s conditions. The ideal gas law is for gas calculations.
What does “reg” mean in the search phrase?
It is not a standard part of the chemistry term Mr. It may be shorthand or a typo, so confirm the intended quantity in the original question before relying on a calculation.
Related
Formula used
in m | Sample mass | g | 44 | 0 in mr | Relative molecular mass (Mr) | g/mol | 44.01 | 0.000001 in t | Gas temperature | °C | 25 | -273.15 in p | Absolute pressure | kPa | 101.325 | 0.000001 out v | Ideal-gas volume | L | (m / mr) * 8.31446261815324 * (t + 273.15) / p | 3 out n | Amount of gas | mol | m / mr | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s