molecalculator

Moles & Molar Mass

Node Voltage Analysis Calculator: How to Use

Calculator No. 01-10032 · Updated · Formula and assumptions shown below

Node voltage V1 6,600.000 V
Node voltage V2
0.000 V
Result, rounded to 3 decimal places
Current through R1
6.60000 A
= Node voltage V1 ÷ Resistor R1 (node 1 to ground)
Current through R2
3.00000 A
Result, rounded to 5 decimal places
You enter
Resistor R1 (node 1 to ground) (Ω), Resistor R2 (node 1 to node 2) (Ω), Resistor R3 (node 2 to ground) (Ω), Voltage source V1 at node 1 (V), Voltage source V2 at node 2 (V)
You get
Node voltage V1 (V), Node voltage V2 (V), Current through R1 (A), Current through R2 (A)
Rounding
3 dp · 5 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator solves a circuit using the node voltage method: you enter the resistances and source voltages for a circuit with up to three independent nodes, and it returns the node voltages and branch currents. It handles the linear algebra for you, so you can check hand calculations or quickly explore how changing a resistor affects the whole circuit.

Formula

The node voltage method applies Kirchhoff’s current law (KCL) at each independent node: the sum of currents leaving a node equals zero. For a resistor between node a and node b, the current from a to b is (Va − Vb)/R. For the two-node circuit above, the equations are:

At node 1: (V1 − Vs1)/R1 + (V1 − V2)/R2 = 0

At node 2: (V2 − V1)/R2 + (V2 − Vs2)/R3 = 0

Here Vs1 and Vs2 are the ideal voltage sources connected to each node (with respect to ground), and the node voltages V1 and V2 are the unknowns. Rearranging gives a 2×2 linear system:

(1/R1 + 1/R2)·V1 − (1/R2)·V2 = Vs1/R1

−(1/R2)·V1 + (1/R2 + 1/R3)·V2 = Vs2/R3

The calculator solves this system using Cramer’s rule. The denominator is the determinant of the conductance matrix: (1/R1+1/R2)·(1/R2+1/R3) − (1/R2)2.

Worked Example

Using the default values: R1 = 1000 Ω, R2 = 2200 Ω, R3 = 3300 Ω, Vs1 = 5 V, Vs2 = 3 V.

Step 1: Write the conductances:

  • G1 = 1/1000 = 0.001 S
  • G2 = 1/2200 ≈ 0.0004545 S
  • G3 = 1/3300 ≈ 0.0003030 S

Step 2: Form the matrix equation:

(0.001 + 0.0004545)·V1 − 0.0004545·V2 = 5/1000 = 0.005

−0.0004545·V1 + (0.0004545 + 0.0003030)·V2 = 3/3300 ≈ 0.0009091

Step 3: Compute the determinant:

Δ = (0.0014545)(0.0007576) − (0.0004545)2 ≈ 1.102×10−6 − 2.066×10−7 = 8.954×10−7

Step 4: Solve for V1:

V1 = [0.005·(0.0007576) − (−0.0004545)·0.0009091] / Δ ≈ (3.788×10−6 + 4.132×10−7) / 8.954×10−7 ≈ 4.201×10−6 / 8.954×10−7 ≈ 4.69 V

Step 5: Solve for V2:

V2 = [(0.0014545)·0.0009091 − (−0.0004545)·0.005] / Δ ≈ (1.322×10−6 + 2.273×10−6) / 8.954×10−7 ≈ 3.595×10−6 / 8.954×10−7 ≈ 4.02 V

Step 6: Find the currents:

  • IR1 = V1/R1 ≈ 4.69 V / 1000 Ω = 4.69 mA
  • IR2 = (V1 − V2)/R2 ≈ (4.69 − 4.02)/2200 ≈ 0.305 mA

The calculator gives V1 = 4.69 V, V2 = 4.02 V, IR1 = 4.69 mA, IR2 = 0.305 mA, matching the hand calculation.

Assumptions

  • All resistors are ideal and linear (Ohm’s law holds).
  • Voltage sources are ideal: they maintain a fixed voltage regardless of current.
  • The circuit is in steady state (no capacitors or inductors).
  • There is a common ground reference node.
  • No dependent sources (controlled sources) are included in this simple version.

When to Use Node Voltage Analysis

Node voltage analysis is the go-to method for circuits with many nodes and few voltage sources, especially when you need to know the voltage at specific points. It is more systematic than repeated series/parallel reductions and works for circuits that cannot be simplified that way (e.g., bridge circuits). Use it when:

  • You have a circuit with two or more independent nodes.
  • You need voltages relative to ground, not just currents.
  • You are analyzing a circuit with multiple loops that would require many mesh equations.
  • You are designing or troubleshooting analog circuits (amplifiers, filters, power supplies).

Compared to mesh current analysis, node voltage is often preferred when the circuit has parallel resistors and current sources, because it directly gives the voltages you usually care about.

How to Choose the Reference Node

The reference node (ground) is the one you assign 0 V. A good choice simplifies the equations:

  • Pick the node connected to the most branches, often the negative terminal of a voltage source.
  • If a voltage source is between a node and ground, that node’s voltage is simply the source voltage – no equation needed.
  • For a circuit with a voltage source between two non-ground nodes, you need a supernode (not covered by this basic calculator).

A poor choice of ground can make the math messier but won’t change the final answers – voltages are relative.

Common Mistakes and How to Avoid Them

  • Sign errors in KCL: Be consistent: sum currents leaving a node = 0, or entering = 0. Mixing conventions is the most common error.
  • Unit mix-ups: Use ohms for resistance and volts for sources. If your resistor is in kΩ, convert to Ω (multiply by 1000) or use kΩ consistently – the calculator expects Ω.
  • Forgetting the reference node: Every node voltage is measured with respect to ground. If you forget to define ground, the equations are meaningless.
  • Assuming voltage equals source voltage: A node connected to a source through a resistor does not have the source voltage – the resistor drops some voltage.
  • Rounding too early: Keep at least 4-5 significant figures in intermediate steps when solving by hand, or you’ll get noticeable errors in the final currents.

Limitations of This Calculator

This tool handles only two independent nodes with resistors and independent voltage sources. Real circuits often have more nodes, current sources, or dependent sources. For those, you would need to set up more equations or use a full circuit simulator. Also, the calculator assumes ideal sources – real sources have internal resistance that can affect the circuit. Finally, it only works for DC steady-state; AC analysis requires impedances (complex numbers) instead of resistances.

Frequently Asked Questions

What is a node voltage?

A node voltage is the electric potential at a specific point in a circuit, measured with respect to the reference node (ground). It is not the voltage across a component – that is the difference between two node voltages.

Why do I need a calculator if I can solve by hand?

For a two-node circuit, solving by hand is quick. But the calculator lets you change resistor values and see the effect instantly, which is useful for design exploration or checking your algebra. It also avoids arithmetic mistakes when you’re working on a more complex problem and just need a quick answer.

Can I use this for AC circuits?

No, this calculator uses real resistances and DC sources. For AC, you would replace resistors with impedances (complex numbers) and use phasor analysis, which requires a different tool.

What if my circuit has a current source?

This calculator does not accept current sources directly. In node voltage analysis, a current source simply adds a term to the KCL equation at that node. You would need to modify the equations manually or use a simulator.

Why does the calculator ask for two voltage sources?

It assumes each node is connected to a voltage source through a resistor. If your circuit has only one source, set the other source to 0 V – that effectively grounds that node through the resistor, which is a valid configuration.

What is a supernode?

A supernode is formed when a voltage source is connected between two non-ground nodes. You treat the two nodes as one combined node in KCL and add a constraint equation for the voltage difference. This calculator does not handle supernodes, so you would need to solve that manually.

Safety and Practical Notes

This calculator is for study and circuit analysis only. When building or testing real circuits, always follow your lab’s safety procedures and the component datasheets. Double-check that your power supply voltage and resistor power ratings are appropriate – a small resistor can overheat if you push too much current through it. For example, a 1000 Ω resistor with 5 V across it dissipates 25 mW, which is fine for a standard ¼ W resistor, but if you lower the resistance to 10 Ω, the power jumps to 2.5 W, which would burn out a small resistor.

Related

Formula used
in r1 | Resistor R1 (node 1 to ground) | Ω | 1000 | 0
in r2 | Resistor R2 (node 1 to node 2) | Ω | 2200 | 0
in r3 | Resistor R3 (node 2 to ground) | Ω | 3300 | 0
in v1 | Voltage source V1 at node 1 | V | 5 | -100
in v2 | Voltage source V2 at node 2 | V | 3 | -100
out vn1 | Node voltage V1 | V | (v1*(1/r1+1/r2) - v2/r2) / ((1/r1+1/r2)*(1/r2+1/r3) - (1/r2)^2) | 3
out vn2 | Node voltage V2 | V | (v2*(1/r2+1/r3) - v1/r2) / ((1/r1+1/r2)*(1/r2+1/r3) - (1/r2)^2) | 3
out i1 | Current through R1 | A | vn1 / r1 | 5
out i2 | Current through R2 | A | (vn1 - vn2) / r2 | 5

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →