Nucleic acid purity ratios are absorbance ratios used to assess whether a DNA or RNA sample may contain substances that absorb ultraviolet light. The A260/A280 ratio is the main quick check: purified DNA is commonly near 1.8, while purified RNA is commonly near 2.0; A260/A230 provides a second check for contaminants such as salts and organic compounds. These are interpretation guides, not a calculator or proof of purity.
What the ratios measure
Nucleic acids absorb UV light strongly near 260 nanometres (nm), largely because of their nitrogen-containing bases. Proteins absorb near 280 nm, mainly because of certain aromatic amino acids. Many compounds used in extraction and purification absorb around 230 nm. A spectrophotometer measures absorbance at these wavelengths, and software or the user calculates one absorbance divided by another.
- A260/A280 = absorbance at 260 nm ÷ absorbance at 280 nm. It is used chiefly to flag possible protein or phenol carryover.
- A260/A230 = absorbance at 260 nm ÷ absorbance at 230 nm. It can flag carryover of salts, extraction reagents, carbohydrates, or other UV-absorbing substances.
Absorbance has no unit, so each ratio is also dimensionless. The wavelength is part of the measurement definition: these values should not be treated as interchangeable with readings taken at other wavelengths.
Typical reference values
For relatively clean material measured under suitable conditions, a commonly used reference is about 1.8 for DNA and about 2.0 for RNA at A260/A280. A260/A230 is often expected to be roughly 2.0–2.2. These are approximate conventions, not universal acceptance limits. Sample type, pH, ionic strength, concentration, instrument, and blanking can shift the observed values.
A result slightly outside a reference range does not automatically mean the sample is unusable. Instead, interpret the ratio alongside the spectrum, concentration, extraction method, and intended downstream application. A sensitive enzyme reaction may be affected by trace contaminants that would not matter for a less demanding use.
How to interpret A260/A280
A low A260/A280 value can be consistent with protein contamination, phenol carryover, or other substances that increase absorbance near 280 nm. It can also result from measurement conditions: acidic pH tends to lower the apparent ratio, while alkaline pH can raise it. Therefore, a low reading alone does not identify a specific contaminant.
A ratio around 1.8 is a useful DNA reference, but double-stranded DNA, single-stranded DNA, and RNA do not have identical absorption characteristics. For RNA, a value near 2.0 is commonly cited. Do not apply the DNA reference mechanically to RNA or assume that a number above the reference proves a sample is exceptionally pure.
How to interpret A260/A230
A low A260/A230 ratio often draws attention to residual material absorbing near 230 nm. Potential sources include chaotropic salts, phenol, carbohydrates, and some extraction-buffer components. The ratio can be especially helpful when A260/A280 appears acceptable but a sample still performs poorly in downstream reactions.
A260/A230 is sensitive to blank choice and baseline behavior. If the blank does not match the sample’s buffer, the resulting spectrum and ratios may be misleading. A high or unusual ratio can also occur when absorbance is very low, because small measurement errors then have a larger proportional effect.
Measurement and interpretation
Most UV spectrophotometric systems report the absorbance values and ratios automatically. A reliable interpretation starts with a well-matched blank and a spectrum that has the expected shape, rather than relying on a single displayed number. Follow the instrument’s instructions and the laboratory’s validated method for sample handling and cleaning.
- Check that the blank uses the same buffer or solvent as the sample whenever the method calls for it.
- Confirm that absorbance is within the instrument’s useful measurement range; very dilute samples produce unstable ratios.
- Review the full UV spectrum for unexpected peaks or baseline problems, not just the two ratios.
- Compare readings with a second method when purity or concentration is important to a specific application.
At the bench, follow your lab method, the safety data sheet (SDS) and your supervisor. UV measurements and sample handling should follow the instrument and laboratory safety procedures.
Ratios are not concentration measurements
Purity ratios describe the relative absorbance at selected wavelengths; they do not tell you how much nucleic acid is present. Concentration is estimated from absorbance at 260 nm using a conversion factor appropriate to the nucleic-acid type and measurement path length, or measured by another validated method. A sample can have a near-ideal ratio but too little material for an experiment, or a high concentration with substantial contamination.
Likewise, a good ratio cannot confirm that DNA is intact, that RNA is free of degradation, or that a sample contains only one nucleic-acid species. Gel or capillary analysis can provide information about integrity and size. Fluorescence-based assays can be more selective for nucleic acid than UV absorbance when contaminants or mixed sample components are a concern.
Common problems and misconceptions
- “A ratio of 1.8 proves pure DNA.” It only suggests that absorbance at 260 and 280 nm is consistent with a common reference. Other contaminants and degradation may not be revealed.
- “Every DNA sample should be exactly 1.8.” The value is an approximate benchmark; sample chemistry and measurement conditions matter.
- “A low ratio identifies the contaminant.” Several substances and measurement issues can produce similar shifts. Ratios are screening clues, not chemical identification.
- “A260/A230 is always 2.0.” About 2.0–2.2 is often cited, but it is not a rigid pass/fail boundary.
If a reading seems implausible, check the blank, buffer match, sample concentration, spectrum, and instrument range before deciding that purification failed. Re-measuring a properly prepared sample can help distinguish a real sample issue from a measurement artifact.
Frequently Asked Questions
What is a good A260/A280 ratio for DNA?
A value near 1.8 is the conventional reference for relatively pure DNA. Treat it as a guide, since sample type and measurement conditions can alter the result.
What is a good A260/A280 ratio for RNA?
RNA is commonly expected to be near 2.0. Use the criteria appropriate to the RNA preparation and intended application rather than comparing it directly with the DNA benchmark.
What does a low A260/A230 ratio mean?
It can indicate carryover of substances absorbing near 230 nm, including salts or extraction reagents, but it can also reflect blanking or baseline problems. It does not identify a contaminant by itself.
Can purity ratios show whether RNA is degraded?
No. A260/A280 and A260/A230 assess absorbance relationships, not molecular integrity. Use an appropriate integrity analysis when degradation matters.
Can a sample have good ratios but a poor concentration reading?
Yes. Ratios and concentration answer different questions, and low absorbance can make both concentration estimates and ratios less reliable. Consider the measurement range and use an appropriate concentration method.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %