For routine cell-culture surface coating, poly-L-lysine (PLL) is commonly used at about 0.01–0.1 mg/mL, with 0.1 mg/mL a frequent starting concentration; the right value depends on the cell type, surface, and product instructions. This calculator works out the PLL mass needed from a target concentration and coating-solution volume, and reports both milligrams and micrograms.
Formula
The mass required is concentration multiplied by final solution volume:
m = c × v
- m is the mass of poly-L-lysine in milligrams (mg).
- c is the target concentration in milligrams per milliliter (mg/mL).
- v is the final coating-solution volume in milliliters (mL).
- To express mass in micrograms, multiply milligrams by 1,000: µg = m × 1,000.
This calculation treats the stated volume as the final solution volume, not the volume of solvent before adding PLL. It does not determine how much coating solution a particular culture surface requires, or whether a chosen concentration is suitable for a particular experiment.
Worked Example
Using the calculator’s defaults, the target concentration is 0.1 mg/mL and the final volume is 10 mL.
- Calculate the PLL mass: m = c × v = 0.1 mg/mL × 10 mL = 1.000 mg.
- Convert to micrograms: 1.000 mg × 1,000 µg/mg = 1,000 µg.
The result is 1.000 mg (1,000 µg) of PLL for 10 mL of solution at 0.1 mg/mL.
Assumptions
- The concentration is a mass-per-volume concentration, not a molar concentration.
- The volume entered is the final volume of the coating solution.
- The PLL material is treated as the reagent specified by the applicable protocol; the calculator does not correct for purity, salt form, moisture, or active-content assay.
- This is planning arithmetic only. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
What concentration should you use?
There is no single PLL coating concentration that is correct for every application. A range around 0.01–0.1 mg/mL is a commonly encountered starting range for cell-culture surfaces, but published methods and product directions can specify values outside it. Different cell types attach differently, and the surface material and coating protocol also affect the result. Treat the range as a guide for locating a suitable validated method, not as a universal recommendation.
Check the instructions and protocol for the exact PLL product you have. Poly-L-lysine products can differ in molecular weight, form, and other specifications. A concentration stated for one product or application should not automatically be transferred to another. If adapting a method, use a controlled comparison and assess the outcome that matters for your experiment, such as cell attachment and morphology.
Also distinguish PLL from poly-D-lysine (PDL). They are related polymers but are not interchangeable labels; protocols may specify one particular polymer and its product characteristics. Follow the polymer identity in the method rather than assuming that a similar name means identical performance.
How to use the calculator and choose inputs
Enter the target concentration in mg/mL and the final volume in mL. The calculator multiplies those values, so increasing either the concentration or volume increases the mass required proportionally. For example, doubling the final volume while keeping the same target concentration doubles the PLL mass.
- Keep units consistent. The concentration field expects mg/mL and the volume field expects mL. If a method gives a concentration in µg/mL, divide that number by 1,000 to enter mg/mL; for example, 50 µg/mL = 0.05 mg/mL.
- Calculate the amount for the volume you will actually prepare. Avoid preparing a much larger volume just because the arithmetic is convenient; use the handling and storage guidance in the applicable method.
- Use the final-volume convention. A target of 0.1 mg/mL in 10 mL means 1 mg of PLL in 10 mL total solution. It does not mean adding 1 mg to 10 mL of solvent and assuming the final volume remains exactly 10 mL.
- Consider weighing resolution. Very small calculated masses may be difficult to measure accurately with the available balance. A validated concentrated stock and an appropriate dilution calculation may be more practical, provided the protocol permits it.
As a unit check, mg/mL multiplied by mL leaves mg: the milliliter units cancel. This simple check catches a common error: entering a volume in microliters as though it were milliliters. Convert µL to mL by dividing by 1,000 before entering it.
How PLL coating works and what the number means
Poly-L-lysine is a positively charged polymer under commonly used aqueous conditions. Many cell surfaces and glass surfaces carry net negative charge, so PLL can promote attachment through electrostatic interactions. The calculator’s answer is the mass needed to make a solution with the chosen bulk concentration. It does not calculate the amount that remains on the surface after coating, nor does it directly predict cell adhesion.
Surface treatment depends on details beyond the solution concentration, including the substrate, contact time, rinsing or drying steps, and the cell type. Those parameters belong to the validated procedure being followed. A higher concentration is not automatically better: it can change surface properties and may produce unwanted effects for a given assay. Likewise, a low concentration can be inadequate for a particular combination of cells and surface.
Common mistakes and limits
- Confusing mg/mL with µg/mL: 0.1 mg/mL equals 100 µg/mL, not 0.1 µg/mL.
- Using solvent volume instead of final volume: concentration is defined using the total solution volume.
- Assuming one concentration fits all: the suitable working condition depends on the application and product instructions.
- Ignoring product specifications: polymer form, molecular-weight range, and assay information can matter when reproducing a protocol.
- Treating calculated mass as coating uptake: the mass placed into solution is not necessarily the mass deposited on a dish or retained after rinsing.
This tool performs only the concentration-to-mass calculation. It does not provide a coating procedure, assess sterility, determine storage stability, or replace the product documentation and institutional laboratory practices. Use the method’s stated conditions and safety information for those decisions.
Frequently Asked Questions
What is a typical poly-L-lysine coating concentration?
A frequently used starting point is 0.1 mg/mL, and concentrations around 0.01–0.1 mg/mL are commonly encountered. The suitable value is application-specific, so check the method and product directions.
How much PLL do I need for 10 mL at 0.1 mg/mL?
You need 1 mg, because 0.1 mg/mL × 10 mL = 1 mg.
Is 0.1 mg/mL the same as 100 µg/mL?
Yes. Multiply mg/mL by 1,000 to convert to µg/mL, so 0.1 mg/mL equals 100 µg/mL.
Does a higher PLL concentration always improve cell attachment?
No. A higher concentration is not automatically better and may not suit a given cell type, substrate, or assay. Follow a validated protocol and assess the relevant experimental outcome.
Can I use a poly-D-lysine concentration in place of poly-L-lysine?
Do not assume they are interchangeable. Use the polymer specified by the protocol, since polymer identity and product characteristics can affect the method.
Does the calculated mass tell me how much PLL coats the surface?
No. It gives the mass to include in the solution at the selected concentration and volume. The amount that adsorbs to or remains on a surface depends on the coating procedure and substrate.
Related
Formula used
in c | Target PLL concentration | mg/mL | 0.1 | 0 in v | Coating solution volume | mL | 10 | 0 out m | PLL mass required | mg | c * v | 3 out u | PLL mass required | µg | m * 1000 | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s