molecalculator

Moles & Molar Mass

Power Density to E-Field Calculator and Formula

Calculator No. 01-2080 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts electromagnetic power density into the electric-field strength that corresponds to a specified wave impedance. Enter power density in watts per square metre and the wave impedance in ohms; the calculator returns electric-field strength in volts per metre, plus the corresponding root-mean-square magnetic-field strength. For a uniform plane wave in free space, use the free-space impedance of about 376.73 Ω.

Formula

For a uniform plane wave, average power density is related to the root-mean-square electric and magnetic fields by S = Erms2/Z = Hrms2Z, where S is average power density in W/m², Erms is electric-field strength in V/m, Hrms is magnetic-field strength in A/m, and Z is wave impedance in ohms. Rearranging gives Erms = √(SZ) and Hrms = √(S/Z). The calculator uses the entered impedance; for a plane wave in free space, Z0 = √(μ0/ε0) ≈ 376.730313668 Ω.

These equations describe the relationship between fields and average energy flow for a plane wave. They do not establish that a real antenna, nearby field, or complex indoor environment has that impedance or a uniform wave.

Worked Example

Using the calculator defaults, S = 1 W/m² and Z = 376.730313668 Ω:

  • Erms = √(1 × 376.730313668) = 19.409544… V/m, or 19.4095 V/m to four decimal places.
  • Hrms = √(1 ÷ 376.730313668) = 0.051527… A/m, or 0.051527 A/m to six decimal places.

The two outputs are consistent with S = ErmsHrms for a free-space plane wave: their unrounded product is 1 W/m².

Assumptions

  • The wave is a uniform plane wave and the stated power density is its time-averaged value.
  • The entered impedance is real and positive; the free-space default applies to a wave propagating in free space.
  • Fields are reported as RMS values, not peak amplitudes.
  • For a sinusoidal field, peak electric field is √2 times its RMS value. The calculator does not report peak field.

How to Convert Power Density to Electric Field

Power density describes how much electromagnetic power crosses a unit area, while electric-field strength describes the electric part of the wave. For a plane wave in free space, their relationship is not a direct multiplication: electric field is the square root of power density multiplied by the wave impedance. This square root matters. If power density increases by a factor of four, field strength increases by a factor of two, not four.

For example, with the free-space impedance, a power density of 10 W/m² gives Erms = √(10 × 376.730313668) ≈ 61.377 V/m. The units also check: (W/m²) × Ω = (V·A/m²) × (V/A) = V²/m²; taking the square root gives V/m.

If a source gives power density in mW/cm², convert it before entering the value: 1 mW/cm² = 10 W/m². If it gives mW/m², divide by 1000 to obtain W/m². The calculator expects nonnegative power density and a positive impedance. Zero power density produces zero field under this idealized relation.

RMS, Peak, and Impedance

The formula here returns RMS field strength. For a sinusoidal electric field, Epeak = √2 Erms; for the example at 1 W/m², the peak field is about 27.45 V/m. Do not apply that conversion automatically to every waveform: the relationship between peak and RMS depends on the waveform. Also distinguish electric-field amplitude from power density; they are different quantities with different units.

Free-space impedance is approximately 376.73 Ω, often rounded to 377 Ω. In a uniform plane wave in a lossless material, impedance depends on the material’s permeability and permittivity, so the free-space value may not apply. In lossy media, or where fields are reactive or near-field, impedance can be complex and electric and magnetic fields may not be in the simple ratio assumed here. A single real impedance input cannot represent all those conditions.

When This Conversion Applies—and Its Limits

This conversion is useful when a power-density value is known and the situation reasonably approximates a plane wave, such as a sufficiently distant field from a source in an unobstructed region. Distance alone does not guarantee far-field conditions; antenna dimensions and wavelength also matter. A field probe, validated model, or measurement method appropriate to the environment may be needed when the assumption is uncertain.

Near an antenna or other source, electric and magnetic fields can be out of phase or have a ratio unlike the free-space wave impedance. Reflections, standing waves, nearby objects, polarization, and spatial variation can also make a local field differ from an estimate based on average power density. In these cases, do not treat this calculator’s result as a measurement or a compliance determination.

Power density is not the same as transmitter output power. To estimate density from source power, additional information such as antenna gain, distance, orientation, and propagation conditions is required. Even a basic far-field estimate depends on those inputs and assumptions; this calculator does not infer them.

Frequently Asked Questions

What is the formula to convert power density to electric field?
For a uniform plane wave, Erms = √(SZ), where S is average power density in W/m² and Z is wave impedance in ohms. In free space, use Z ≈ 376.73 Ω.

What electric field corresponds to 1 W/m² in free space?
It is √(1 × 376.730313668) ≈ 19.41 V/m RMS. The corresponding sinusoidal peak field is about 27.45 V/m.

Can I use 377 ohms for free space?
Yes, 377 Ω is a common rounded value. Using 376.73 Ω is slightly more precise; the difference in the calculated field is small for ordinary estimates.

How do I convert mW/cm² to W/m²?
Multiply by 10. For instance, 1 mW/cm² equals 10 W/m². Convert the power-density units before using the calculator.

Does this work near an antenna?
Not necessarily. Close to a source, the fields may not behave like a uniform plane wave, and the free-space impedance relationship may not hold. Use an appropriate measurement or field model for that setting.

Related

Formula used
in s | Power density | W/m^2 | 1 | 0
in z | Wave impedance | ohm | 376.730313668 | 0.000001
out e | Electric field strength, RMS | V/m | sqrt(s * z) | 4
out h | Magnetic field strength, RMS | A/m | sqrt(s / z) | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →