A pressure–specific volume (P–v) diagram plots a substance’s pressure against its specific volume, the volume occupied per unit mass. This calculator converts a sample’s mass and volume into specific volume and pairs it with a specified pressure, giving the coordinates of one state—not a complete thermodynamic curve.
Formula
The calculator’s first result is specific volume: vsp = V / m. Here, V is the sample’s total volume in cubic metres (m³), and m is its mass in kilograms (kg); the result, vsp, is in m³/kg. The second result is density, ρ = m / V, in kg/m³. These quantities are reciprocals when they describe the same uniform sample: ρ = 1/vsp.
Pressure, p, is entered in kilopascals (kPa) because it identifies the vertical coordinate of the state on a P–v diagram. The horizontal coordinate is specific volume. Pressure does not enter the specific-volume formula: a single pressure and volume-to-mass ratio establish one plotted point, but they do not determine the shape of a process path or the full diagram.
Worked Example
Using the default inputs—pressure 100 kPa, mass 1 kg, and volume 0.001 m³:
- Specific volume: vsp = V / m = 0.001 m³ / 1 kg = 0.0010 m³/kg.
- Density: ρ = m / V = 1 kg / 0.001 m³ = 1000.00 kg/m³.
- The plotted state is (vsp, p) = (0.0010 m³/kg, 100 kPa).
The pressure is shown as the state’s pressure coordinate; it is not needed to calculate the specific volume.
Assumptions
- The mass and volume refer to the same sample and state.
- The supplied volume is the sample’s total volume, not a volume per unit mass.
- The entered pressure is absolute pressure if the diagram or equation of state calls for absolute pressure. The calculator does not convert gauge pressure.
- The calculation is a unit conversion and ratio; it does not assume an ideal gas or infer a phase.
What a P–v Diagram Shows
A P–v diagram is a thermodynamic state diagram. Pressure is plotted vertically and specific volume horizontally. Because specific volume is volume divided by mass, it is an intensive property: doubling the amount of a uniform material doubles its total volume but leaves its specific volume unchanged at the same state.
For a fixed quantity of material, a path across the diagram represents a process that changes pressure and specific volume. A point represents a state, while a line connecting points represents a sequence of states or an idealized process. The diagram’s axes do not by themselves say how quickly the process happens, how much heat flows, or whether the path is physically achievable; those conclusions require process information and an appropriate model.
In common diagrams for a pure substance, a saturation dome may mark the region where liquid and vapor coexist. Its left boundary corresponds to saturated liquid and its right boundary to saturated vapor. Within the dome, quality (the vapor mass fraction) helps specify the state. Outside it, the substance may be a compressed or subcooled liquid on one side, or a superheated vapor on the other. The dome’s shape and numerical coordinates depend on the substance and are obtained from property data, not from this calculator alone.
How to Plot a State or Process
To place a state, calculate specific volume and use the state’s pressure. To draw a process, you need multiple states or a relationship between pressure and specific volume, plus enough information to evaluate intermediate points. A practical plotting sequence is:
- Identify the substance and the thermodynamic state or process being studied.
- Obtain pressure and total volume and mass at each known state, or use suitable property tables or an equation of state to determine missing properties.
- Convert quantities to consistent units, then calculate vsp = V/m for each state.
- Plot pressure vertically against specific volume horizontally and label units, states, and process direction.
- Use property data to identify phase boundaries or quality where those features matter.
For example, if a 2 kg sample occupies 0.5 m³ at 200 kPa, its specific volume is 0.25 m³/kg. That gives the point (0.25 m³/kg, 200 kPa). It does not reveal whether the sample is liquid, vapor, or a mixture; temperature or other property information and the substance’s phase data are needed.
Reading the Axes and Avoiding Mistakes
Specific volume and total volume are not interchangeable. A horizontal coordinate of 0.25 m³/kg means each kilogram occupies 0.25 m³; it is not a total sample volume unless the sample mass is exactly 1 kg. For a fixed mass, total volume can be recovered as V = m vsp.
Check units before comparing points. One cubic metre is 1000 litres, and one kilopascal is 1000 pascals. If pressure is given in bar or MPa, convert it or label the axis consistently. Also distinguish absolute pressure from gauge pressure: gauge pressure is measured relative to local atmospheric pressure, while absolute pressure is measured from a vacuum. Many thermodynamic property tables and equations of state require absolute pressure. Do not treat a gauge reading as absolute without conversion.
Another common misconception is that pressure alone determines specific volume. It does not. A gas’s pressure and volume also depend on temperature, amount of substance, and its thermodynamic behavior. For liquids, volume changes may be small over some pressure ranges, but pressure still does not uniquely specify a state in every situation. Use the material’s property data and the conditions relevant to the problem.
Limits and Related Diagrams
This calculator is useful for turning measured mass and volume into a diagram-ready coordinate. It does not generate saturation curves, determine phase, calculate work, or create a process path from one point. Those tasks need additional state variables, an equation of state, or substance-specific tables. Even a plotted curve may be an idealization: real measurements have uncertainty, and a diagram’s apparent detail depends on scale and data coverage.
A P–v diagram is often compared with a P–V diagram. The latter uses total volume, an extensive property that changes with sample size; P–v uses specific volume, making comparisons between different sample amounts more meaningful. Other useful thermodynamic plots include temperature–entropy (T–s) and pressure–enthalpy (P–h) diagrams. Each emphasizes different properties and process calculations, so none is universally interchangeable with the others.
Frequently Asked Questions
What does a pressure–specific volume diagram show?
It shows pressure versus volume per unit mass for a substance. A plotted point identifies a state in those two properties; a path can represent a process when its states are known.
How do you calculate specific volume?
Divide total volume by mass: vsp = V/m. Use compatible units, such as m³ and kg, to obtain m³/kg.
What is the difference between specific volume and density?
Specific volume is volume per unit mass, while density is mass per unit volume. For the same sample and state, they are reciprocals: vsp = 1/ρ.
Can pressure and specific volume identify the phase?
Not always. Phase identification generally requires the substance’s property data and may need another property such as temperature. Pressure and specific volume alone are not enough in every region or for every material.
Is a P–v diagram the same as a P–V diagram?
No. P–v uses specific volume per unit mass; P–V uses the sample’s total volume. The two horizontal coordinates differ by the sample mass.
Related
Formula used
in p | Pressure | kPa | 100 | 0 in m | Mass | kg | 1 | 0 in v | Volume | m³ | 0.001 | 0 out sv | Specific volume | m³/kg | v / m | 4 out rho | Density | kg/m³ | m / v | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Meters Into Liters Calculator: The Missing Dimension