molecalculator

Moles & Molar Mass

Progress of Reaction Graph: How to Read It

Calculator No. 01-12054 · Updated · Formula and assumptions shown below

Forward activation energy 70.0 kJ/mol
Reverse activation energy
140.0 kJ/mol
= Energy of transition state − Energy of products
Overall energy change (ΔE)
-70.0 kJ/mol
= Energy of products − Energy of reactants
Energy of reactants
50 kJ/mol
Set in the form below
You enter
Energy of reactants (kJ/mol), Energy of products (kJ/mol), Energy of transition state (kJ/mol)
You get
Forward activation energy (kJ/mol), Reverse activation energy (kJ/mol), Overall energy change (ΔE) (kJ/mol)
Rounding
1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A progress of reaction graph (also called a reaction coordinate diagram) plots the energy of a chemical system as a function of the reaction coordinate—a measure of how far the reaction has progressed from reactants to products. You enter the energy values of the reactants, products, and transition state, and the calculator returns the activation energy for the forward and reverse reactions and the overall energy change (ΔE).

Formula

The graph is built from three energy values, each measured relative to the same zero (usually the energy of separated reactants or a defined reference state). The key quantities are:

  • Forward activation energy (Ea,f) = Etransition state − Ereactants
  • Reverse activation energy (Ea,r) = Etransition state − Eproducts
  • Overall energy change (ΔE) = Eproducts − Ereactants

All energies are in kJ/mol. The transition state is the highest-energy point along the most favorable reaction path; it is not an isolated molecule but a fleeting arrangement of atoms with partial bonds.

Worked Example

Using the default values: reactants at 50 kJ/mol, products at −20 kJ/mol, and transition state at 120 kJ/mol.

  1. Forward activation energy: 120 − 50 = 70 kJ/mol
  2. Reverse activation energy: 120 − (−20) = 140 kJ/mol
  3. Overall ΔE: −20 − 50 = −70 kJ/mol (exothermic)

The reaction is exothermic because products sit lower in energy than reactants. The reverse reaction has a higher barrier (140 kJ/mol) than the forward one (70 kJ/mol), so the forward reaction is faster at a given temperature, all else being equal.

Assumptions

  • Energies are relative; only differences matter for the shape of the graph.
  • The reaction proceeds through a single transition state (no intermediates).
  • No catalyst is present; a catalyst would lower the transition state energy.
  • Temperature and pressure are constant; the graph shows potential energy, not free energy (unless specified).

How to Read the Graph

The horizontal axis is the reaction coordinate—a simplified measure of bond breaking and forming. It runs from pure reactants (left) to pure products (right). The vertical axis is energy. The curve rises to a maximum at the transition state, then falls to products.

  • Peak height = activation energy; a higher peak means a slower reaction at a given temperature.
  • Difference in starting and ending heights = ΔE; negative ΔE (products lower) means exothermic, positive means endothermic.
  • Symmetry: If the transition state is closer in energy to reactants, the reaction is more exothermic (Hammond’s postulate).
  • Multiple peaks indicate reaction intermediates; each peak is a separate transition state.

Remember: the graph does not show time. A reaction with a small activation energy can still be slow if the pre-exponential factor (frequency of collisions) is low.

Common Mistakes and Misconceptions

  • Confusing ΔE with activation energy: ΔE tells you whether the reaction releases or absorbs energy overall; activation energy tells you how fast it goes. A reaction can be highly exothermic yet have a large activation energy (e.g., burning paper).
  • Thinking the transition state is a stable species: It is a transient arrangement with a lifetime on the order of a vibrational period (~10−13 s).
  • Using the wrong sign for ΔE: If products are lower than reactants, ΔE is negative (exothermic). Many students mistakenly report a positive value because they think “energy released” is positive.
  • Ignoring the reverse barrier: The reverse activation energy is just as important for equilibrium; it determines the rate of the reverse reaction.
  • Assuming the graph is to scale: In textbooks, the curve is often sketched with exaggerated peaks for clarity; always read the numbers.

When to Use a Progress of Reaction Graph

These graphs are used in chemistry courses to illustrate reaction mechanisms, compare catalyzed vs. uncatalyzed paths, and explain why some reactions are kinetically stable despite being thermodynamically favorable. In research, they help predict whether a reaction will occur at a reasonable rate at a given temperature. The activation energy can be measured experimentally using the Arrhenius equation:

k = A · e−Ea/(RT)

where k is the rate constant, A is the pre-exponential factor, R = 8.314 J/(mol·K), and T is temperature in kelvin. If you know the rate constants at two temperatures, you can solve for Ea. This calculator gives you the energy differences; you can then plug Ea into the Arrhenius equation to estimate rate changes.

Limitations of the Model

The simple one-hump graph assumes a single elementary step. Most real reactions involve multiple steps, each with its own transition state. The graph also ignores entropy and temperature effects; strictly, the y-axis should be Gibbs free energy (ΔG) if you want to predict spontaneity. For reactions in solution, solvation effects can change the relative energies significantly. The transition state theory assumes a quasi-equilibrium between reactants and the transition state, which is a good approximation for many reactions but not all.

Frequently Asked Questions

What is the difference between activation energy and ΔE?

Activation energy is the energy barrier that must be overcome for the reaction to proceed; ΔE is the net energy difference between products and reactants. A reaction can have a large activation energy (slow) and still be highly exothermic (releases a lot of energy).

Can the progress of reaction graph show the rate of reaction?

Not directly. The graph shows energy changes along the reaction coordinate, not time. However, the activation energy influences the rate constant via the Arrhenius equation: a lower barrier means a faster reaction at a given temperature.

Why is the transition state drawn as a peak, not a plateau?

The transition state is a maximum on the potential energy surface—a saddle point. It is the highest-energy point along the minimum-energy path, so it appears as a peak. A plateau would indicate a stable intermediate, not a transition state.

How does a catalyst change the graph?

A catalyst provides an alternative pathway with a lower transition state energy, so the peak is lower. The overall ΔE remains the same because the catalyst does not change the initial and final states. The graph would show a new, lower hump.

What does a negative ΔE mean on the graph?

It means the products have lower energy than the reactants, so the reaction is exothermic (releases energy). The products will be drawn lower on the y-axis than the reactants.

Can the transition state energy be lower than both reactants and products?

No. By definition, the transition state is a maximum along the reaction coordinate. If it were lower than both, it would be a stable intermediate, not a transition state. The peak must be higher than both endpoints.

Follow your lab method, the safety data sheet (SDS) and your supervisor when performing any experimental work.

Related

Formula used
in e_r | Energy of reactants | kJ/mol | 50 | -1000 | 1000
in e_p | Energy of products | kJ/mol | -20 | -1000 | 1000
in e_ts | Energy of transition state | kJ/mol | 120 | -1000 | 1000
out ea_f | Forward activation energy | kJ/mol | e_ts - e_r | 1
out ea_r | Reverse activation energy | kJ/mol | e_ts - e_p | 1
out de | Overall energy change (ΔE) | kJ/mol | e_p - e_r | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →