Liquid propane expands to roughly 270 times its liquid volume when it becomes gas at atmospheric pressure and about 15.6 °C (60 °F). This calculator estimates the gas volume from a liquid volume, or the liquid equivalent of a gas volume, using that approximate ratio.
Formula
For liquid-to-gas conversion, gas volume = liquid volume × expansion ratio. For gas-to-liquid conversion, liquid volume = gas volume ÷ expansion ratio. In the calculator, v is the liquid propane volume in liters, g is the propane gas volume in liters, and d is the selected direction (1 for liquid to gas, 0 for gas to liquid). The expansion ratio used is 270:1. The displayed conversion result is in liters; the unused volume input is ignored by the selected direction.
The ratio is an approximation, not a universal material constant. It describes a comparison between liquid and vapor volumes at specified conditions. Gas volume depends strongly on temperature and pressure, so a ratio is meaningful only when its reference conditions are understood. This calculator uses the common approximate value of 270 and treats the resulting vapor as near atmospheric-pressure gas at roughly 15.6 °C.
Worked Example
Using the defaults, the selected direction is liquid to gas, the liquid volume is 1 L, and the expansion ratio is 270:
- Gas volume = liquid volume × expansion ratio
- Gas volume = 1 L × 270 = 270 L
The calculator therefore returns 270.000 L of propane gas, rounded to three decimal places. This is a volume comparison at the stated reference conditions, not a prediction that a container will safely hold or release that amount.
Assumptions
- The expansion ratio is approximately 270:1, a conventional rounded value rather than an exact constant.
- The gas-volume estimate is for propane vapor near atmospheric pressure and about 15.6 °C.
- The liquid and vapor are treated as pure propane; commercial fuel can include minor constituents.
- The calculator converts volume only. It does not determine mass, energy content, flow rate, pressure, or safe equipment capacity.
What the 270-to-1 Ratio Means
Propane is stored as a liquid under pressure. When some liquid leaves a pressurized container and reaches conditions where propane is gaseous, the same amount of material occupies much more space. The familiar 270:1 figure means that one volume unit of liquid corresponds approximately to 270 volume units of vapor under the comparison conditions. Thus, one liter of liquid corresponds to about 270 liters of gas, and one gallon corresponds to about 270 gallons of gas.
The ratio is about volume, not mass. The propane molecules do not multiply or disappear during vaporization; their spacing changes. This distinction matters when reading a fuel label or estimating how much vapor a liquid quantity represents. A volume ratio also does not say how quickly liquid will evaporate: vaporization rate depends on heat transfer, exposed surface area, pressure, and other conditions.
Why Temperature and Pressure Matter
A gas has no fixed volume independent of its surroundings. At a higher pressure, a given quantity of propane vapor occupies less space; at a higher temperature, it generally occupies more space if pressure is held constant. Consequently, the “gas” side of the expansion ratio must refer to a pressure and temperature. The commonly quoted figure is a convenient engineering approximation, not a promise that every liter of liquid will produce exactly 270 liters in every room, pipe, or process.
Propane’s liquid density also varies with temperature, so converting between a measured liquid volume and a gas volume adds another condition-sensitive step. For precise engineering, metering, or inventory work, use propane property data for the actual temperature and pressure and define whether volumes are actual or standardized. Standardized gas volumes are reported at specified reference conditions; different standards can produce different numerical volumes for the same amount of gas.
Using the Calculator and Checking Units
Choose the direction that matches the value you know, then enter that volume in liters. The first result is the converted volume, also in liters. For example, for 2.5 L of liquid propane, the approximate gas equivalent is 2.5 × 270 = 675 L. For 540 L of gas, the liquid equivalent is 540 ÷ 270 = 2 L.
Convert other units before entering them. One US liquid gallon is about 3.785 L, so 1 US gallon of liquid propane corresponds approximately to 3.785 × 270 = 1,021.95 L of gas at the calculator’s reference conditions. Do not confuse a US gallon with an Imperial gallon, or liters of liquid with liters of gas. The answer can look surprisingly large because the phases have very different densities.
This simple calculator is useful for understanding scale and making rough comparisons. It is not suitable by itself for sizing regulators, pipes, ventilation, storage, or combustion equipment. Those tasks require flow rates, operating pressure, temperature, appliance demand, applicable codes, and equipment specifications.
Common Misconceptions and Safety
A common misconception is that the ratio means a propane cylinder contains 270 times its marked liquid capacity as pressurized gas. The ratio instead compares liquid volume with the much larger volume the vapor would occupy at a specified low pressure. A cylinder’s water capacity, permitted fill, pressure rating, and vapor withdrawal limits are separate matters; never use this ratio to decide how much to fill a container or whether it can contain gas safely.
Propane is highly flammable, and escaping gas can form a fire or explosion hazard. It can also displace oxygen in an enclosed space. Use and store propane only in approved equipment and in accordance with applicable instructions and regulations; keep it away from ignition sources, and ensure suitable ventilation. If a leak is suspected, do not operate switches or create sparks: leave the area and contact emergency services or the appropriate gas-safety service from a safe location.
Frequently Asked Questions
What is the expansion ratio of liquid propane to gas?
About 270:1 by volume under commonly referenced conditions near atmospheric pressure and 15.6 °C. The exact value changes with the reference temperature and pressure.
How much gas does one liter of liquid propane make?
Approximately 270 L of vapor at the conditions assumed here. It is a volume equivalent, not a safe container capacity or a guaranteed volume under other pressures and temperatures.
How many liters of liquid propane equal 1,000 liters of gas?
Using 270:1, divide 1,000 L by 270: 1,000 ÷ 270 ≈ 3.70 L of liquid propane.
Does propane expand exactly 270 times?
No. “270 times” is a rounded rule of thumb. Gas temperature and pressure, and the liquid’s temperature, affect the comparison.
Is the expansion ratio the same as propane’s pressure in a tank?
No. The ratio compares volumes across liquid and gas phases. Tank pressure depends mainly on propane temperature while liquid and vapor coexist, and it is not calculated from the 270:1 volume ratio.
Related
Formula used
in v | Liquid propane volume | L | 1 | 0 in g | Propane gas volume | L | 270 | 0 sel d | Conversion direction | Liquid to gas=1, Gas to liquid=0 out r | Propane volume conversion | L | d * v * 270 + (1 - d) * g / 270 | 3 out e | Expansion factor | - | 270 | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Gas Correction Factor Formula and Calculator0.9829
- Gas Correction Factor Calculator and Table1.2534
- Gas Temperature: Calculate It from Pressure and Volume298.15 K
- Gas Correction Factor Calculator: Formula and Uses107.322 same as input
- Density Temperature Correction Calculator and Formula999.25 kg/m^3
- Gas Cv Calculator: Heat Capacity Ratio and Formula20.786 J/(mol·K)