molecalculator

Moles & Molar Mass

Protein Concentration and Absorbance Calculator

Calculator No. 01-5537 · Updated · Formula and assumptions shown below

Protein concentration 0.5000 mg/mL
Protein concentration
500.0 µg/mL
= Protein concentration × 1000
Absorbance
0.5 AU
Set in the form below
Mass extinction coefficient
1 L/(g·cm)
Set in the form below
You enter
Absorbance (AU), Mass extinction coefficient (L/(g·cm)), Optical path length (cm)
You get
Protein concentration (mg/mL), Protein concentration (µg/mL)
Rounding
4 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator estimates protein concentration from absorbance using the Beer–Lambert law: enter the measured absorbance, the protein’s mass extinction coefficient, and the optical path length to get concentration in mg/mL. The result is valid only when the absorbance is measured at the coefficient’s specified wavelength and under compatible conditions.

Formula

The Beer–Lambert relationship for a protein solution is A = εcl. Rearranging for mass concentration gives c = A/(εl). The calculator calls the absorbance A (a dimensionless reading, often displayed in absorbance units or AU), the mass extinction coefficient ε (L·g−1·cm−1), and the optical path length l (cm). Its output c is in g/L, numerically equivalent to mg/mL: 1 g/L = 1 mg/mL. The second output converts this value to µg/mL by multiplying by 1000.

This calculator uses a mass extinction coefficient rather than a molar extinction coefficient. If a coefficient is supplied in M−1·cm−1, it cannot be entered directly: convert it using the protein’s molar mass. For a molar coefficient εm in L·mol−1·cm−1 and molar mass MW in g/mol, the mass coefficient is ε = εm/MW in L·g−1·cm−1.

Worked Example

Using the calculator’s default values, absorbance is 0.5 AU, the mass extinction coefficient is 1 L·g−1·cm−1, and path length is 1 cm.

  1. Apply the rearranged equation: c = A/(εl).
  2. Substitute the defaults: c = 0.5/(1 × 1) = 0.5 g/L.
  3. Convert units: 0.5 g/L = 0.5 mg/mL.
  4. Convert to micrograms per milliliter: 0.5 × 1000 = 500.0 µg/mL.

The calculator therefore reports 0.5000 mg/mL and 500.0 µg/mL. The default coefficient is a convenient arithmetic example, not a universal value for proteins; use a coefficient appropriate to the specific protein and wavelength.

Assumptions

  • Absorbance is blank-corrected and measured in the instrument’s linear range.
  • The entered mass extinction coefficient applies to the protein, wavelength, and solution conditions.
  • The sample is sufficiently clear and dilute for Beer–Lambert behavior; scattering and strong interactions are negligible.
  • The path length is the actual optical path through the sample, in centimeters.

How Absorbance Relates to Protein Concentration

Absorbance describes how much light a sample removes from a beam at a selected wavelength. In an ideal, homogeneous solution, more absorbing molecules along the light path produce greater absorbance. Beer–Lambert law expresses that proportionality, which is why concentration can be calculated when absorbance, path length, and an appropriate extinction coefficient are known.

Protein absorbance in the ultraviolet is commonly associated with aromatic amino acids, especially tryptophan and tyrosine, and to a lesser degree cystine. Since proteins differ in amino-acid composition, they do not all absorb equally at the same mass concentration. A coefficient calculated from a protein’s sequence can be more suitable than a generic estimate, but it still depends on the wavelength and assumptions used in the calculation. At 280 nm, a protein’s absorbance is often used for concentration estimates; nucleic acids and other UV-absorbing compounds can interfere.

Absorbance is not itself a concentration. A value such as A280 = 0.5 does not uniquely specify protein concentration unless the path length and coefficient are also known. Likewise, “one absorbance unit” does not mean one standard concentration. It is a measure of optical attenuation, not a mass or amount of protein.

Choosing Inputs and Using the Result

  • Absorbance: enter the sample reading after subtracting the appropriate blank. Use the reading at the wavelength for which the coefficient is defined.
  • Mass extinction coefficient: check its units carefully. A value in L·g−1·cm−1 is suitable for this calculator. If the source gives a molar coefficient, convert it using the protein’s molar mass before entering it.
  • Path length: a standard cuvette is often designed for a 1 cm path, but other cells and microvolume measurements may have shorter paths. Use the actual path length or a validated instrument-reported equivalent.
  • Output units: mg/mL and g/L have the same numerical value. To convert mg/mL to mg/L, multiply by 1000; to convert mg/mL to µg/mL, also multiply by 1000.

For example, halving the path length while keeping the sample and wavelength unchanged halves absorbance. If the path length is known and the absorbance remains within the valid range, the equation corrects for that difference. The result is still an estimate whose accuracy depends on measurement quality and the coefficient.

Limits and Common Problems

Beer–Lambert calculations are most reliable when absorbance is within the linear range of the instrument and the sample is clear. At high absorbance, little light reaches the detector, and stray light or detector limitations can cause the measured value to depart from the simple proportional relationship. Diluting a sample and accounting for the dilution factor can help, provided the dilution is made and recorded accurately and the protein remains soluble.

Turbidity, suspended particles, bubbles, or aggregation can scatter light and raise apparent absorbance. A buffer blank that differs from the sample matrix can also bias the result. Other substances absorbing at the selected wavelength—including nucleic acids—may make a UV estimate too high. A protein-specific coefficient does not correct for these contaminants.

Errors in units are another common source of misleading results. Entering a molar extinction coefficient where a mass coefficient is required can produce a result wrong by a factor related to the protein’s molar mass. Similarly, using a path length in millimeters as though it were centimeters causes a tenfold error. Keep the coefficient and path length units consistent with the formula.

Absorbance-based concentration is not always the best method. For a mixed protein sample, an unknown protein, or a sample containing UV-absorbing contaminants, a colorimetric assay or a calibration curve made with a suitable protein standard may be more appropriate. Such assays have their own response differences and interference risks, so follow the method’s stated range and blanking instructions. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

Frequently Asked Questions

How do you calculate protein concentration from absorbance?
Use c = A/(εl), where A is blank-corrected absorbance, ε is the mass extinction coefficient in L·g−1·cm−1, and l is path length in cm. The result is in g/L, numerically the same as mg/mL.

What is a typical protein extinction coefficient?
There is no single typical value that works for every protein. The coefficient depends on amino-acid composition and wavelength; use a value calculated or measured for the protein when available, and verify its units.

Can I use A280 to measure any protein?
A280 can estimate concentration when the protein’s coefficient is known and interfering UV absorbers are absent or negligible. Proteins with different aromatic amino-acid content give different signals, and nucleic acids can interfere.

Does absorbance depend on path length?
Yes. Under Beer–Lambert conditions, absorbance is proportional to path length. A measurement made with a shorter optical path must be interpreted using that actual path length, not automatically as if it were measured in a 1 cm cuvette.

Why is my absorbance-based concentration too high?
Possible causes include turbidity or bubbles, nucleic-acid contamination, an unsuitable blank, an incorrect extinction coefficient, or a path-length or unit error. Check the wavelength, blank, sample clarity, and coefficient units before interpreting the estimate.

Related

Formula used
in a | Absorbance | AU | 0.5 | 0
in k | Mass extinction coefficient | L/(g·cm) | 1 | 0.000001
in l | Optical path length | cm | 1 | 0.000001
out c | Protein concentration | mg/mL | a / (k * l) | 4
out cm | Protein concentration | µg/mL | c * 1000 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →