molecalculator

Moles & Molar Mass

Purity on Mass Balance: Formula and Worked Example

Calculator No. 01-3577 · Updated · Formula and assumptions shown below

Purity 92.00 %
Impurity mass
0.80 g
= Total sample mass − Mass of desired component
Total sample mass
10 g
Set in the form below
Mass of desired component
9.2 g
Set in the form below
You enter
Total sample mass (g), Mass of desired component (g)
You get
Purity (%), Impurity mass (g)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Purity from a mass balance is the mass of the desired component divided by the total mass of the sample, multiplied by 100%. Enter the sample’s total mass and the mass of the desired component to calculate purity as a percentage; the result assumes both masses refer to the same sample and that the component mass is known.

Formula

The mass-balance purity formula is:

Purity (%) = (mass of desired component ÷ total sample mass) × 100%

  • ms is the total mass of the sample, in grams (g).
  • mp is the mass of the desired, or target, component in that sample, in grams (g).
  • P is the mass purity, expressed as a percentage.

The calculator also reports impurity mass: mi = ms − mp. Both input masses must use the same unit; using grams for one and milligrams for the other without conversion gives an invalid result. The inputs must be nonnegative, and the target-component mass cannot physically exceed the total sample mass. If it does, the stated measurements or their units need checking.

Worked Example

Using the calculator’s defaults, the total sample mass is 10 g and the desired component’s mass is 9.2 g.

  1. Divide the target-component mass by the total sample mass: 9.2 g ÷ 10 g = 0.92.
  2. Convert the fraction to a percentage: 0.92 × 100% = 92.00%.
  3. Find the impurity mass: 10 g − 9.2 g = 0.80 g.

The sample is therefore 92.00% pure by mass, with 0.80 g of material not counted as the target component.

Assumptions

  • The two measurements describe the same sample, at the same relevant point in the process.
  • The target-component mass is known or measured independently and is included in the total sample mass.
  • Purity means mass fraction of the specified target component, not purity by mole, volume, or number of particles.
  • The sample’s components are accounted for by the total mass; mass lost or gained during handling must be considered if it changes the measured sample.

What a Mass-Balance Purity Calculation Means

A mass balance accounts for material entering, leaving, and remaining in a defined process or sample. For a simple purity calculation, the boundary is usually one weighed sample: its total mass is the denominator, while the mass of the component being assessed is the numerator. This produces a mass fraction, which is commonly reported as a percentage.

For example, a material can be described as 92% pure by mass if 92% of its measured mass is the specified substance. That statement does not identify what makes up the remaining 8%. It could be one impurity or several, residual water, solvent, or other material. The formula calculates the share assigned to the target; it does not identify or characterize the rest.

Purity depends on defining the target clearly. “Pure” is not meaningful by itself if the sample contains several useful components. In a mixture, specify which substance counts as the desired component and use a method that measures that component specifically.

How to Use the Result and Choose the Right Basis

Use mass purity when the question is how much of a weighed sample is the desired material. It is often suitable for a solid mixture or a material whose composition is reported by mass. Keep the calculation basis consistent: if the total mass includes moisture, then the numerator and denominator describe the sample as received, unless the target mass is also corrected to a dry basis.

Two common reporting bases are:

  • As-received (wet) basis: the denominator is the sample mass including its measured moisture or other volatile content.
  • Dry basis: the denominator is the sample mass after moisture has been excluded or corrected for, and the target mass must be expressed on that same basis.

These figures can differ substantially. A dry-basis result is not directly comparable with an as-received result unless the moisture correction is known. Similarly, mass percent is not interchangeable with mole percent: mole percent uses the number of moles of each component, so components with different molar masses contribute differently to the two percentages.

For a stream-based process balance, use a clearly defined time period and account for all relevant inlet and outlet streams, accumulation, and losses. A purity calculation on one product sample is not by itself a complete process mass balance. If multiple components are known, a fuller balance may compare the sum of their masses with the sample’s total mass.

Common Errors and Limits

  • Mixing units: Convert milligrams to grams (divide by 1,000) or kilograms to grams (multiply by 1,000) before comparing masses.
  • Using the wrong denominator: The denominator is the total sample mass, not the mass of the impurity or the amount of solvent added.
  • Confusing purity with recovery: Purity describes composition. Recovery describes how much of the target material was obtained from an earlier amount; it needs a starting target mass as well as a recovered target mass.
  • Counting a measurement twice: The target mass is part of the sample’s total mass. Do not add it to the total again.
  • Reporting unjustified precision: The calculator displays two decimal places, but a result cannot be more reliable than its inputs and measurement method. Report significant figures in line with the measurement uncertainty or applicable reporting rules.

The simple formula assumes the target mass is known. If it was inferred from an assay, titration, or instrumental measurement, the method’s calibration, selectivity, and uncertainty affect the result. A mass difference can estimate impurity mass only when the sample mass is fully accounted for and the target component is the only portion separated out by the calculation. If components are missing from the balance, or the sample changes during measurement, that difference may not represent actual impurities.

Frequently Asked Questions

What is the formula for purity by mass?
Divide the mass of the desired component by the total sample mass, then multiply by 100. The result is the sample’s mass purity in percent.

Can purity be more than 100%?
Not for a physically consistent mass fraction using a target mass that is part of the sample. A result above 100% usually points to a unit mismatch, an incorrect sample boundary, double counting, or measurement error.

How do I calculate impurity mass?
If the total sample mass and target-component mass are known, subtract the target mass from the total: impurity mass = total sample mass − target-component mass. This treats all remaining mass as non-target material; it does not identify individual impurities.

Is purity the same as concentration?
No. Purity is the fraction of a sample that is the specified component. Concentration describes how much of a component is present relative to a defined amount of solution or mixture, such as grams per litre or moles per litre.

Does moisture affect purity?
It does if moisture is included in the sample mass. State whether the result is on an as-received or dry basis, and make sure both the target mass and total mass use the same basis.

Can I use this formula for a solution?
Yes, if you know the mass of the target component and the total mass of the solution, it gives mass percent. Do not substitute solution volume for total mass; a volume-based concentration requires a different formula and suitable volume measurements.

Related

Formula used
in ms | Total sample mass | g | 10 | 0
in mp | Mass of desired component | g | 9.2 | 0
out p | Purity | % | 100 * mp / ms | 2
out i | Impurity mass | g | ms - mp | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →