An RCA calculator is commonly used to work out relative centrifugal acceleration (RCA), more often called relative centrifugal force (RCF), from a centrifuge’s rotational speed and rotor radius. Enter the speed in revolutions per minute and the radius in centimetres to get the acceleration relative to Earth’s gravity.
Formula
Relative centrifugal force is the centrifugal acceleration at the sample’s position divided by standard gravitational acceleration. The calculator uses:
RCF = 1.118 × 10−5 × r × RPM2
- RCF is the relative centrifugal force, expressed as a multiple of Earth’s standard gravitational acceleration, or × g.
- r is the rotor radius in centimetres, measured from the axis of rotation to the sample’s location.
- RPM is rotational speed in revolutions per minute.
The coefficient incorporates the conversion from centimetres to metres, minutes to seconds, and standard gravity, approximately 9.80665 m/s². The equivalent physical acceleration is a = RCF × 9.80665 m/s². RCF is a ratio, not a force in newtons; the calculator’s × g label means “times standard gravity.”
Worked Example
Using the calculator’s default values—10,000 rpm and a 10 cm radius:
- Square the speed: 10,0002 = 100,000,000 rpm².
- Substitute into the formula: RCF = 1.118 × 10−5 × 10 × 100,000,000 = 11,180 × g.
- Convert the result to acceleration: a = 11,180 × 9.80665 = 109,658.447 m/s².
Rounded to the calculator’s two decimal places, the results are 11,180.00 × g and 109,658.45 m/s².
Assumptions
- The stated radius is the distance from the rotation axis to the sample location, not the rotor’s outside diameter.
- The rotor is rotating at the entered speed; the calculation does not account for acceleration or braking time.
- Standard gravity is 9.80665 m/s². RCF is a kinematic calculation and does not depend on sample density.
- For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
How to Measure Radius and Use the Result
Radius is the distance from the centre of rotation to the point in the tube or vessel whose RCF you need. It is not necessarily the rotor’s listed maximum radius. For a swinging-bucket rotor, the radius changes as the bucket moves from its resting position to its operating position; use the radius specified for the rotor and condition relevant to the protocol. A rotor manual or method may define whether its reference point is the sample bottom, centre, or another position.
That location matters because RCF increases in direct proportion to radius. In a tube extending from 8 cm to 12 cm from the axis, the force at the outer end is 1.5 times the force at the inner end at the same RPM. If a protocol specifies an RCF but your instrument displays RPM, calculate the required speed by rearranging the formula:
RPM = √(RCF ÷ (1.118 × 10−5 × r))
For example, to find the approximate speed corresponding to 5,000 × g at a 10 cm radius, use √(5,000 ÷ (1.118 × 10−5 × 10)), which is about 6,688 rpm. The rotor’s permitted maximum speed and the method’s requirements still need to be checked independently.
Why RPM and RCF Are Not Interchangeable
RPM describes how quickly the rotor turns. RCF describes the acceleration acting at a particular radius. Therefore, the same RPM can produce different RCF values on different rotors, and a given RCF can require different RPM values depending on rotor geometry. Reporting only RPM may not communicate the separation conditions clearly when another rotor is used.
Because RPM is squared, a small speed change can have a larger effect on RCF. At a fixed radius, raising speed by 10% multiplies RCF by 1.1², or 1.21: a 21% increase. Doubling the radius, by contrast, doubles RCF when speed is unchanged. These relationships explain why both inputs must be correct.
Common Errors and Limits
- Entering diameter as radius: If a rotor dimension is given as a 20 cm diameter, its radius is 10 cm. Entering 20 cm instead doubles the calculated RCF.
- Using the wrong radius reference: The axis-to-sample distance depends on the sample position and rotor geometry. Confirm which position the protocol or rotor specifications use.
- Mixing up RPM and RCF: A speed in rpm cannot be entered as a target in × g. Convert using the formula and the correct radius.
- Assuming a universal RPM-to-RCF conversion: There is no single conversion without a radius. A conversion from another rotor may not apply to yours.
- Ignoring instrument limits: This calculation does not establish that a rotor, tube, cap, or sample container is rated for the computed speed or force. Follow the applicable specifications and method.
The equation gives the centrifugal acceleration at a chosen radius during rotation. It does not predict how quickly particles sediment, how well a separation will work, or how long a run should last. Those outcomes also depend on particle size and shape, liquid viscosity and density, sample volume, rotor design, temperature, and the protocol. Use the calculator for a unit conversion or planning check, not as a replacement for method-specific instructions.
Frequently Asked Questions
What does RCA mean on a centrifuge?
In this context, RCA is often intended to mean relative centrifugal acceleration. The more standard abbreviation is RCF, for relative centrifugal force. Both descriptions refer to acceleration expressed as a multiple of standard gravity.
How do I calculate RCF from RPM?
Multiply 1.118 × 10−5 by the rotor radius in centimetres and by RPM squared. The radius and the speed must use the units specified in that formula.
How do I convert RCF to RPM?
Use RPM = √(RCF ÷ (1.118 × 10−5 × r)), with the radius in centimetres. Check that the resulting speed is within the rotor and instrument limits.
Does rotor radius affect RCF?
Yes. At a fixed RPM, RCF is directly proportional to radius. Use the distance from the rotational axis to the sample point required by the protocol, rather than assuming the rotor diameter is the relevant value.
Is RCF the same as RPM?
No. RPM measures rotation rate; RCF expresses acceleration relative to gravity. RCF depends on both RPM and radius, so the same RPM can correspond to different RCF values on different rotors.
Related
Formula used
in rpm | Rotor speed | rpm | 10000 | 0 in r | Radius from axis to sample | cm | 10 | 0 out rcf | Relative centrifugal force | × g | 1.118 * 10^-5 * r * rpm^2 | 2 out a | Centrifugal acceleration | m/s² | rcf * 9.80665 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp