molecalculator

Moles & Molar Mass

RCF vs G-Force: What Centrifuge RCF Means

Calculator No. 01-2245 · Updated · Formula and assumptions shown below

Relative centrifugal force 1,006 × g
Equivalent speed at a 10 cm radius
3,000 rpm
Result, rounded to a whole number
Rotor radius
10 cm
Set in the form below
Speed
3000 rpm
Set in the form below
You enter
Rotor radius (cm), Speed (rpm)
You get
Relative centrifugal force (× g), Equivalent speed at a 10 cm radius (rpm)
Rounding
0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

RCF means relative centrifugal force: the acceleration a sample experiences in a centrifuge, expressed as a multiple of Earth’s standard gravitational acceleration, g. It is often called “g-force,” but it is not the same as the rotor’s speed in revolutions per minute (rpm); the conversion depends on the rotor radius.

Formula

Relative centrifugal force is calculated as RCF = 1.118 × 10−5 × r × rpm2. Here, RCF is the force as a multiple of standard gravity (× g), r is the rotor radius in centimetres, and rpm is rotational speed in revolutions per minute. The coefficient incorporates unit conversions and standard gravity. The formula assumes the stated radius is the distance from the axis of rotation to the sample position being considered.

The calculator’s second result converts the calculated RCF to the rpm that would produce the same force at a 10 cm radius. That comparison is only illustrative: it does not mean a different rotor can be run at that speed safely or that the two setups separate samples identically.

Worked Example

Using the defaults, the radius is 10 cm and the speed is 3,000 rpm.

RCF = 1.118 × 10−5 × 10 × 3,0002
RCF = 1.118 × 10−5 × 10 × 9,000,000
RCF = 1,006.2 × g, which rounds to 1,006 × g.

Equivalent speed at a 10 cm radius = √(1,006.2 ÷ (1.118 × 10−5 × 10)) = 3,000 rpm, or 3,000 rpm rounded to a whole revolution per minute.

Assumptions

  • The radius is measured in centimetres from the rotor axis to the sample’s relevant position.
  • Speed is constant and entered in revolutions per minute.
  • RCF is calculated using the conventional coefficient 1.118 × 10−5, based on standard gravity.
  • The result is a calculation, not a recommended operating setting; the rotor and centrifuge limits still apply.

How RCF Relates to Centrifuge Speed

A rotating rotor produces radial acceleration, which increases with distance from the rotation axis and with the square of rotational speed. RCF reports that acceleration relative to standard gravity, approximately 9.80665 m/s². Thus, 1,000 × g means an acceleration about one thousand times standard gravity; it does not mean the rotor is turning at 1,000 rpm.

The squared speed term matters. If rotor radius stays unchanged and speed doubles, RCF becomes four times as large. If speed is unchanged and the relevant radius doubles, RCF doubles. Consequently, rpm alone cannot describe the force on a sample unless the rotor geometry is also known.

For example, at 3,000 rpm, a sample 10 cm from the axis experiences about 1,006 × g using the formula above. At the same speed and a 5 cm radius, it experiences about 503 × g. These are mathematical comparisons, not assurances that either speed is permissible for a particular rotor.

Which Rotor Radius Should You Use?

“Rotor radius” can refer to more than one point. Maximum RCF is commonly calculated at the greatest distance from the axis to the sample, often the bottom of a tube in a fixed-angle rotor. Mean RCF uses a representative position, while minimum RCF refers to a position nearer the axis. A swinging-bucket rotor’s sample position changes as the buckets swing out during rotation.

For a useful comparison, use the same radius convention as the protocol or rotor documentation. If a protocol specifies maximum RCF, use the maximum sample radius rather than the rotor’s outside diameter or the tube length. Radius is measured from the rotation axis to the sample location, not across the rotor. When documentation provides a conversion table or radius, use it rather than estimating from a photograph.

Samples also occupy a range of distances within a tube, so different parts of the sample can experience different RCF. A single calculator result is therefore an approximation tied to the radius entered, not a complete description of every particle’s path.

When RCF Is More Useful Than RPM

RCF is generally the more transferable setting when comparing centrifuges with different rotor sizes. A protocol that gives only rpm may not transfer directly to another rotor: maintaining the same rpm with a smaller radius gives a lower RCF, while a larger radius gives a higher one. If a method specifies RCF, use that target along with the specified rotor type, run time, temperature, and other conditions.

Even matching RCF does not guarantee identical separation. Rotor geometry affects sedimentation paths and path lengths; sample volume, tube shape, density, viscosity, and run duration also matter. RCF is a key operating quantity, not a complete substitute for a validated method.

For a quick conversion, identify the radius associated with the method, enter it in centimetres, and enter the intended speed in rpm. Check that the output is in the expected range. To find the speed for a target force, rearrange the formula: rpm = √(RCF ÷ (1.118 × 10−5 × r)). Confirm the result against the rotor’s approved operating limits before use.

Common Mistakes and Safety

  • Confusing × g with rpm: RCF is relative acceleration; rpm is rotational speed.
  • Using the wrong radius: radius is a distance from the axis, not the rotor diameter. A radius entered in millimetres must be converted to centimetres by dividing by 10.
  • Using an arbitrary sample position: maximum, mean, and minimum radius yield different RCF values. Follow the method’s stated convention.
  • Assuming equal RCF means identical results: rotor geometry and sample conditions can still change separation.

Never exceed the maximum speed or force rating of the rotor, buckets, tubes, or accessories. Follow the centrifuge and rotor instructions, use compatible components, and balance loads as directed. An rpm calculated from an RCF target is not permission to operate equipment beyond its limits. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

Is RCF the same as g-force?
Yes, in centrifuge use RCF is commonly called g-force. It states acceleration as a multiple of standard gravity, such as 1,000 × g.

How do I convert rpm to RCF?
Use RCF = 1.118 × 10−5 × radius in cm × rpm². You need the radius as well as the speed.

Can I convert RCF to rpm?
Yes, if the rotor radius is known: rpm = √(RCF ÷ (1.118 × 10−5 × radius in cm)). Check the resulting speed against equipment limits.

Why does the same rpm give different RCF?
RCF is proportional to radius. A sample farther from the rotation axis experiences greater acceleration at the same rotational speed.

Should I use maximum or average RCF?
Use the radius convention specified by the protocol or rotor documentation. Do not substitute maximum RCF for average RCF without checking, because they describe different sample positions.

Related

Formula used
in r | Rotor radius | cm | 10 | 0.1
in rpm | Speed | rpm | 3000 | 0
out rcf | Relative centrifugal force | × g | 1.118e-5 * r * rpm ^ 2 | 0
out rpm2 | Equivalent speed at a 10 cm radius | rpm | sqrt(rcf / (1.118e-5 * 10)) | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →