RCF is not the same as g: RCF is the relative centrifugal force experienced in a centrifuge, expressed as a multiple of Earth’s gravitational acceleration, g. For example, 500 × g means a force equivalent to 500 times standard gravity; it does not mean 500 grams or a mass of 500 g. This calculator converts between RCF and revolutions per minute (RPM) when you enter the rotor radius.
Formula
The calculator uses the standard relationship between relative centrifugal force and rotational speed:
RCF = 1.118 × r × (RPM / 1,000)2
RPM = 1,000 × √[RCF / (1.118 × r)]
- RCF is relative centrifugal force, stated as a multiple of standard gravity, often written × g.
- r is the rotor radius in centimetres, measured from the axis of rotation to the sample’s position.
- RPM is rotational speed in revolutions per minute.
- 1.118 is the rounded conversion constant for this form of the equation. It incorporates the conversion from centimetres and RPM to acceleration relative to standard gravity, 9.80665 m/s².
The first calculator result is RCF, calculated from the entered rotor radius and speed. The second is the RPM needed to reach the entered RCF at that radius. Each output uses the corresponding input values; use one calculation direction at a time by entering the target value for that direction. For a more precise calculation, use the full relationship RCF = (2π × RPM / 60)2 × rm / 9.80665, where the radius rm is in metres.
Worked Example
Using the default values—radius 10 cm, speed 5,000 RPM, and target RCF 2,797.55 × g—the RCF calculation is:
RCF = 1.118 × 10 × (5,000 / 1,000)2
RCF = 1.118 × 10 × 25 = 279.5 × g
This is not 2,797.55 × g, so the stated default target would not match the speed result. To preserve the correct formula and a sensible worked example, the default RCF input is 279.5. Then the reverse calculation is:
RPM = 1,000 × √[279.5 / (1.118 × 10)]
RPM = 1,000 × √25 = 5,000 rpm
The first output rounds 279.5 to 280 × g at zero decimal places, and the second output is 5,000 rpm. The formula block’s target default is 2,797.55, however, so use the displayed formulas and the correctly matched values above rather than treating that default as a matching pair.
Assumptions
- The rotor is rotating at a steady speed, and the entered radius is the distance from the rotation axis to the relevant sample position.
- The standard gravity reference is 9.80665 m/s²; RCF is a calculated acceleration ratio, not a direct measurement of sample separation.
- The calculator uses a rounded conversion constant, so its result may differ slightly from a manufacturer’s rotor chart or a calculation using more digits.
Why RCF and g Are Often Confused
The symbol g has more than one common use. In mass measurements, g means gram. In acceleration and centrifugation, g means the standard acceleration due to gravity. RCF is a dimensionless ratio: an RCF of 1 × g corresponds to standard gravity, while 100 × g corresponds to 100 times that acceleration.
For that reason, protocols commonly say “centrifuge at 3,000 × g.” The notation × g makes clear that the instruction is about relative force, not grams. Strictly, acceleration is measured in metres per second squared, while RCF is the acceleration divided by standard gravity. The “× g” notation is a convenient way to express that multiple.
Why Rotor Radius Changes the Result
RCF depends on both speed and radius. At the same RPM, a sample farther from the rotation axis experiences greater acceleration. At the same radius, increasing RPM raises RCF according to the square of the speed: doubling RPM produces four times the RCF, not twice the RCF.
That is why an RPM value alone does not fully specify a centrifugation condition. Two rotors turning at 5,000 RPM can expose samples to different RCFs if their effective radii differ. Conversely, the same RCF can be reached with a lower speed in a larger-radius rotor.
Choosing the Correct Radius
Rotor documentation may give more than one radius. The maximum radius is usually measured from the axis to the bottom or outer edge of the sample position. The minimum radius is closer to the axis. During rotation, particles in a tube travel through a range of radii, so the force also varies along the sample.
- Use the radius specified by the protocol or rotor documentation whenever available.
- Check whether a stated RCF is based on maximum, average, or minimum radius; those conventions can produce different RPM settings.
- Enter centimetres in this calculator. Convert millimetres to centimetres by dividing by 10, or metres to centimetres by multiplying by 100.
- For a swinging-bucket rotor, account for the bucket’s operating position if the documentation defines the radius that way.
If you do not know which radius a protocol uses, do not assume the rotor’s outside dimension is the correct value. Check the rotor’s documentation or ask the person responsible for the method. A radius measured to the wrong point can lead to a substantial difference in calculated force.
Common Calculation Mistakes
- Confusing RPM with RCF: RPM measures rotation speed; RCF describes acceleration relative to gravity. They are related but are not interchangeable.
- Using grams as the unit: RCF is not a mass. Write it as a multiple such as 2,000 × g.
- Entering the wrong radius unit: The constant 1.118 in the displayed formula requires radius in centimetres. A radius of 10 mm must be entered as 1 cm, not 10 cm.
- Forgetting the square: RPM is squared in the RCF formula. A small speed change can therefore make a large change in force.
- Rounding too early: Keep full precision through the calculation and round only the final result, especially when converting a protocol’s target RCF back to RPM.
A calculated RPM is not permission to exceed a rotor’s rated speed. The rotor, tubes, adapters, sample volume, and centrifuge configuration must all be suitable for the operating conditions. Follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
Is 1 g the same as 1 RCF?
Numerically, 1 × g of RCF equals one standard gravitational acceleration, 9.80665 m/s². The lowercase g can also mean grams in another context, so the units and wording matter.
How do I convert RPM to RCF?
Use RCF = 1.118 × radius in centimetres × (RPM / 1,000)². You need the correct radius for the rotor and sample position; RPM alone is insufficient.
Can I use the same RPM for different centrifuges?
You can enter the same RPM, but the resulting RCF may differ because rotor radii differ. Compare RCF, not just RPM, when translating a method between compatible rotors.
What does 500 × g mean?
It means an acceleration 500 times standard gravity. It does not mean 500 grams, and it does not specify a rotor speed unless the radius is also known.
Is RCF constant throughout a tube?
No. Because the radius changes along the tube, the local RCF varies with position. A protocol or rotor chart may identify whether its stated value refers to a particular radius convention.
Related
Formula used
in r | Rotor radius | cm | 10 | 0.000001 in rpm | Rotor speed | rpm | 5000 | 0 in rcf | Relative centrifugal force | × g | 2797.55 | 0 out rcfout | RCF | × g | 1.118 * r * (rpm / 1000) ^ 2 | 0 out rpmout | Rotor speed | rpm | 1000 * sqrt(rcf / (1.118 * r)) | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %