Absorbance is directly proportional to concentration when a sample follows the Beer–Lambert law: at fixed wavelength, path length, and chemical conditions, doubling concentration doubles absorbance. This calculator estimates concentration from absorbance, molar absorptivity, and cuvette path length, or predicts absorbance from those same inputs.
Formula
The Beer–Lambert law is A = εlc. Rearranging to calculate concentration gives c = A / (εl). Here, A is absorbance, which is dimensionless; ε is molar absorptivity in L/(mol·cm); l is the optical path length in cm; and c is concentration in mol/L. The second calculator result converts mol/L to µmol/L by multiplying by 1,000,000.
To predict absorbance instead, use A = εlc. The equation assumes the sample and measurement conditions are suitable for a linear Beer–Lambert relationship. Molar absorptivity is specific to the absorbing substance and wavelength, and can also depend on conditions such as solvent and temperature.
Worked Example
Using the calculator defaults—absorbance 0.500, molar absorptivity 10,000 L/(mol·cm), and path length 1 cm:
- Rearrange the law: c = A / (εl).
- Substitute the values: c = 0.500 / (10,000 × 1) = 0.000050000 mol/L.
- Convert to micromoles per liter: 0.000050000 × 1,000,000 = 50.00 µmol/L.
The displayed concentration is 0.000050 mol/L and 50.00 µmol/L, rounded to the calculator’s specified decimal places.
Assumptions
- The sample follows a linear Beer–Lambert relationship at the chosen wavelength.
- The entered molar absorptivity applies to the substance and measurement conditions.
- The path length is the distance light travels through the sample, in centimeters.
- Absorbance refers to the sample measurement after appropriate blank correction.
Why Absorbance Tracks Concentration
A spectrophotometer measures how much light passes through a sample compared with a reference. Transmittance, T, is the transmitted light intensity divided by the incident intensity. Absorbance is defined as A = −log10(T). A sample that transmits less light therefore has a higher absorbance.
In a dilute, well-behaved solution, increasing the number of absorbing molecules in the light path increases the chance that light will be absorbed. The Beer–Lambert law summarizes this proportionality: concentration and path length each scale absorbance, while molar absorptivity describes how strongly the substance absorbs at a particular wavelength. For example, if the path length and conditions stay fixed, a sample at 20 µmol/L should have twice the absorbance of one at 10 µmol/L, provided both are within the linear range.
Absorbance is not the same as the percentage of light absorbed. Because it is logarithmic, an absorbance of 1 corresponds to 10% transmittance, or 90% of the incident light not transmitted. An absorbance of 2 corresponds to 1% transmittance. This distinction matters when comparing readings or interpreting instrument displays.
Using the Calculator and Choosing Inputs
Enter the measured, blank-corrected absorbance, the molar absorptivity for the analyte at the measurement wavelength, and the optical path length. The calculator returns concentration in mol/L and µmol/L. For the reverse calculation, multiply the concentration by molar absorptivity and path length to estimate absorbance.
- Use the right absorptivity: ε is not a universal constant for a molecule. Find a value measured or specified for the correct wavelength and conditions, or determine a calibration curve with standards.
- Check path length: standard cuvettes often have a 1 cm optical path, but other cells and microvolume setups can differ. Use the actual effective path length.
- Keep units consistent: this calculator expects ε in L/(mol·cm), path length in cm, and reports concentration in mol/L. Do not enter an absorptivity stated in different units without converting it.
- Use corrected absorbance: a blank helps account for absorption or scattering by the solvent, buffer, and cell. Use the reading after the method’s blank correction.
The default absorptivity is an illustrative input, not a universal value for any particular substance. Replace it with a suitable value for the substance being studied.
Calibration, Range, and Common Problems
For quantitative work, a calibration curve is often more reliable than relying on a literature absorptivity alone. Measure standards of known concentration under the same conditions, plot absorbance against concentration, and fit a line over the range where the response is linear. The slope represents εl when the Beer–Lambert model applies; the intercept can reveal a baseline offset. Then use the sample’s absorbance and the calibration equation to estimate its concentration.
Linearity can fail at high concentrations, where molecular interactions, changes in refractive index, chemical equilibria, or stray light affect the measurement. Turbid or particulate samples can scatter light, adding apparent absorbance unrelated to molecular absorption. A poor blank, fingerprints, bubbles, an incorrect wavelength, or a mismatched cuvette can also distort readings. If a sample is above the validated range, dilution may bring it into range; account for the dilution factor when calculating the original concentration.
Uncertainty in absorbance, ε, and path length all contributes to uncertainty in the calculated concentration. Reporting many decimal places does not make a result more precise than the measurements and calibration support. Use appropriate significant figures and state the wavelength, path length, calibration approach, and dilution when reporting results.
Frequently Asked Questions
Does absorbance increase when concentration increases?
Yes, under Beer–Lambert conditions and with wavelength, path length, and sample conditions held constant, absorbance rises in proportion to concentration.
What is the equation connecting absorbance and concentration?
The Beer–Lambert law is A = εlc. To solve for concentration, rearrange it to c = A/(εl).
Is absorbance the same as concentration?
No. Absorbance is a dimensionless optical measurement; concentration is the amount of substance per volume. A relationship between them requires a suitable absorptivity, path length, and valid measurement conditions.
Can I calculate concentration from absorbance alone?
Not generally. You also need a valid calibration curve or an applicable molar absorptivity and the optical path length.
Why might absorbance not be proportional to concentration?
The sample may be outside the linear range, the blank or wavelength may be wrong, or scattering, chemical changes, stray light, and other measurement effects may interfere.
For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Related
Formula used
in a | Absorbance | - | 0.500 | 0 in e | Molar absorptivity | L/(mol·cm) | 10000 | 0 in l | Path length | cm | 1 | 0 out c | Concentration | mol/L | a / (e * l) | 6 out cmg | Concentration | µmol/L | c * 1000000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s