molecalculator

Moles & Molar Mass

Serial Dilution Calculations in Microbiology

Calculator No. 01-6622 · Updated · Formula and assumptions shown below

Estimated original concentration 850,000 CFU/mL
Concentration after dilution steps
1,000 CFU/mL
= Starting concentration × (1 ÷ Dilution factor per step)^Number of dilution steps
Starting concentration
1000000 CFU/mL
Set in the form below
Dilution factor per step
10
Set in the form below
You enter
Starting concentration (CFU/mL), Dilution factor per step, Number of dilution steps, Volume plated (mL), Colonies counted (colonies)
You get
Estimated original concentration (CFU/mL), Concentration after dilution steps (CFU/mL)
Rounding
0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Serial dilution calculations show the concentration of a sample after repeated, measured dilution steps; in microbiology, they are commonly used to calculate colony-forming units per milliliter (CFU/mL) from countable plates. Enter the starting concentration, dilution factor per step, number of steps, and plated volume to estimate the original concentration from a colony count.

Formula

For a plate-count estimate, the original concentration is the number of colonies divided by the volume plated and by the fraction of the original sample represented on the plate:

Coriginal = K / [V × (1 / D)N]

  • Coriginal is the estimated original concentration in CFU/mL.
  • K is the number of colonies counted.
  • V is the plated volume in mL.
  • D is the dilution factor per step, such as 10 for a tenfold dilution.
  • N is the number of equal dilution steps.

The fraction remaining after each step is 1/D, so after N steps the total fraction is (1/D)N. The calculator’s companion output uses C0 × (1/D)N to show the concentration after the stated dilution steps, where C0 is the entered starting concentration in CFU/mL. The colony-count estimate and this forward calculation answer different questions; the first infers a starting concentration from a plate, while the second predicts a diluted concentration from an already known starting value.

Worked Example

Using the calculator’s default values, a plate has 85 colonies after three tenfold dilution steps, and 0.1 mL was plated. The total fraction of the original sample on the plate is:

(1 / 10)3 = 0.001

The effective volume of original sample represented is:

0.1 mL × 0.001 = 0.0001 mL

Therefore:

85 colonies / 0.0001 mL = 850,000 CFU/mL

The calculator rounds the headline result to 0 decimal places: 850,000 CFU/mL. Its separate forward calculation is 1,000,000 CFU/mL × 0.001 = 1,000 CFU/mL after the stated dilution steps. This forward result is not the same as the plate-derived estimate because the entered starting concentration is an independent example value.

Assumptions

  • Each listed dilution step has the same dilution factor and is performed accurately.
  • The plated volume is the actual volume delivered to the plate, in mL.
  • Each colony counted arose from one viable colony-forming unit; clumps can make this assumption false.
  • The colony count is suitable for interpretation under the lab’s method. The calculator does not decide whether a plate is countable.
  • CFU/mL describes culturable colony-forming units under the conditions used, not necessarily every cell present.

How Serial Dilution Works

A serial dilution makes a sequence of lower-concentration samples by transferring a measured portion into a measured amount of diluent, mixing, then repeating. If each step is a tenfold dilution, one part of the previous sample is represented in ten parts total, leaving one-tenth of its concentration. Three such steps yield 10-3, or one-thousandth, of the starting concentration.

Serial dilution is useful when a sample is too concentrated to count or measure directly. In microbiology, a suitable dilution may produce separated colonies on an agar plate. After incubation according to the approved method, a count can be converted to CFU/mL using the total dilution and the plated volume. In other applications, the same arithmetic describes concentrations through a sequence, even when the readout is not a colony count.

Keep the dilution factor and dilution fraction distinct. A “1:10 dilution” usually means a fraction of 1/10 remains, while its reciprocal dilution factor is 10. Multiplying by 10 tracks the reciprocal dilution factor; multiplying concentration by 1/10 tracks what remains. Mixing these conventions reverses the calculation.

Planning and Interpreting a Plate Count

For multiple dilution levels or replicate plates, calculate each valid plate’s estimate using its own colony count, plated volume, and total dilution. Compare replicates and dilution levels for consistency rather than treating every plate as an independent, equally reliable measurement. Follow the specific method’s stated countable range; acceptable ranges depend on the method and organism, so there is no single universal cutoff.

  • Record every step’s transfer fraction and the order of the dilution series.
  • Use the cumulative dilution. For example, three 1:10 steps give a total fraction of 10-3, not 1:10.
  • Convert plated volume correctly. A 100 µL plate is 0.1 mL, so divide by 0.1 mL when the desired answer is CFU/mL.
  • Report the dilution and plated volume alongside the colony count so the result can be checked.
  • Use “CFU/mL” rather than “cells/mL” unless a separate method establishes cell numbers; one colony may arise from a clump.

When the plate has zero colonies, the formula returns zero, but that does not establish that the original sample contains no viable organisms. It means none were detected in the plated portion under those conditions. A result below the method’s detection limit may be more informative than reporting zero as an exact concentration.

Common Calculation Errors and Limits

The most frequent arithmetic error is applying the per-step factor only once instead of raising it to the number of steps. Another is using the dilution factor where the remaining fraction belongs: for a tenfold dilution, concentration is multiplied by 0.1, not 10. Unit errors also matter. If the plated volume is entered in microliters, convert it to milliliters before using a formula expressed in CFU/mL.

Rounding intermediate dilution values can introduce avoidable error, especially across many steps. Keep the exact fraction or scientific notation through the calculation, then round the final result to sensible precision. A colony count is itself an integer observation, but the inferred concentration remains an estimate affected by sampling variation, mixing, plating technique, clumping, growth conditions, and the method’s detection limits.

This calculator assumes equal dilution factors and a single plated volume and count. For unequal steps, multiply the actual fractions together. For replicate plates, calculate and interpret them according to the experimental method rather than simply entering a combined count with one plate’s volume. The arithmetic cannot correct a mislabeled tube, poor mixing, contamination, or a plate that is unsuitable for counting.

Frequently Asked Questions

How do I calculate CFU/mL from a serial dilution?
Divide the colony count by the plated volume in mL multiplied by the total dilution fraction. For a count of 85 after three 1:10 steps with 0.1 mL plated, the estimate is 85 / (0.1 × 0.001) = 850,000 CFU/mL.

What does a 10-3 dilution mean?
It means one-thousandth of the original concentration remains, assuming the dilution steps were made correctly. Its reciprocal dilution factor is 103, or 1,000.

How many serial dilution steps should I use?
Choose steps that are likely to produce a measurable result, using the expected concentration and the range accepted by the relevant method. There is no fixed number appropriate for every sample; pilot results or established protocols can guide the choice.

Can I use this calculation when a plate has no colonies?
The arithmetic gives zero, but a zero count indicates no colonies were observed in the plated portion, not proof of absence in the original sample. Interpret it against the plated volume, total dilution, detection limit, and method.

Why is the result reported as CFU/mL instead of cells/mL?
Plate counting measures colony-forming units. A colony may originate from one cell or a cluster of cells, and cells that do not grow under the test conditions are not counted.

Is a 1:10 dilution the same as a dilution factor of 10?
They describe reciprocal quantities: 1:10 commonly denotes a remaining fraction of 1/10, while the dilution factor is 10. State which convention is being used to avoid multiplying in the wrong direction.

Safety and Laboratory Practice

Microbiological samples may contain organisms that pose health risks. Use only approved laboratory procedures, suitable containment and personal protective equipment, and proper waste handling; do not culture unknown samples outside an authorized setting. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Related

Formula used
in c0 | Starting concentration | CFU/mL | 1000000 | 0
in df | Dilution factor per step | - | 10 | 1
in n | Number of dilution steps | - | 3 | 0
in v | Volume plated | mL | 0.1 | 0.000001
in k | Colonies counted | colonies | 85 | 0
out c | Estimated original concentration | CFU/mL | k / (v * (1 / df)^n) | 0
out cd | Concentration after dilution steps | CFU/mL | c0 * (1 / df)^n | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →