This solution dilution calculator finds the volume of a concentrated stock needed to prepare a target concentration in micrograms per milliliter (µg/mL), along with the diluent volume. Enter the stock concentration, target concentration, and final volume; the result uses the dilution equation and checks that the target is achievable from the stock.
Formula
The calculation uses the conservation-of-solute equation C₁V₁ = C₂V₂. Rearranged for the volume of stock: V₁ = (C₂ × V₂) / C₁. The diluent volume is V₂ − V₁.
- C₁ is the stock concentration in µg/mL.
- V₁ is the stock solution volume to transfer, in mL.
- C₂ is the target concentration in µg/mL.
- V₂ is the final solution volume, in mL.
Because both concentrations use the same unit and both volumes use mL, no conversion factor is needed. If your stock and target concentrations use different units, convert them to the same unit before calculating. The expression adds 0 × sqrt(C₁ − C₂) so that a target above the stock is rejected as “Cannot compute,” rather than producing a misleading negative stock volume.
Worked Example
Using the default values—stock concentration 1000 µg/mL, target concentration 100 µg/mL, and final volume 10 mL:
- Calculate stock volume: V₁ = (100 µg/mL × 10 mL) / (1000 µg/mL) = 1.0000 mL.
- Calculate diluent volume: 10 mL − 1.0000 mL = 9.0000 mL.
The calculator therefore reports 1.0000 mL of stock and 9.0000 mL of diluent. The volumes sum to the specified 10 mL final volume.
Assumptions
- The starting and target concentrations refer to the same dissolved substance and are expressed in µg/mL.
- The final volume is the total volume of the prepared solution, not the volume of diluent alone.
- The dilution calculation assumes the solute amount is conserved and that mixing does not cause a reaction, precipitation, or loss.
- For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
How to Use the Calculator
Choose the concentration and volume values from your preparation plan, then enter them in the matching fields. The calculator returns the volume of stock and the amount of diluent needed to reach the stated final volume.
- Use the concentration of the stock solution as it actually exists, not the concentration of a more concentrated intermediate unless that is what you will take.
- Enter the target concentration and final volume you intend to obtain.
- Use consistent units. If the stock is listed in mg/mL, convert it to µg/mL: 1 mg/mL = 1000 µg/mL.
- Use the displayed stock volume as a calculated volume, then make up to the specified final volume according to the validated method for your work.
For instance, 0.25 mg/mL is 250 µg/mL, while 2 µg/mL is 0.002 mg/mL. Converting before calculation prevents a thousand-fold error. If the answer is a volume too small to measure reliably with the equipment available, consider a suitably planned intermediate dilution rather than rounding the value to zero.
What µg/mL Means
A microgram per milliliter is a mass concentration: it describes how many micrograms of a substance are present in each milliliter of solution. The prefix “micro” means one-millionth, so 1 µg = 0.000001 g. Also, 1 µg/mL = 1 mg/L. These equivalent units can be useful when comparing a label, protocol, or analytical result that uses a different notation.
Mass concentration is not the same as molar concentration. Converting µg/mL to mol/L requires the substance’s molar mass, because equal masses of different compounds contain different numbers of molecules. This calculator does not perform that conversion; it calculates a dilution using mass concentration only.
Limits and Common Mistakes
The requested target concentration must be no greater than the stock concentration for a simple dilution. Diluting adds solvent or diluent and lowers concentration; it cannot make a solution more concentrated. If the target exceeds the stock, use a more concentrated starting solution or revise the preparation plan rather than interpreting a negative calculated volume as usable.
- Confusing final volume with diluent volume: in the example, the target is 10 mL total. Adding 10 mL of diluent to 1 mL of stock would not produce a 10 mL final volume.
- Mixing up mg/mL and µg/mL: they differ by a factor of 1000. Convert both concentrations into the same unit first.
- Rounding too early: retain enough digits during calculation, especially for small stock volumes. Round only to a volume your available measuring method can support.
- Ignoring concentration uncertainty: the arithmetic cannot correct an inaccurate stock concentration, degradation, incomplete mixing, or volume-measurement error.
The formula is an ideal mass-balance calculation, not a guarantee of chemical stability or suitability for a particular experiment. Changes in volume on mixing, solubility, adsorption, and chemical reactions may matter in some systems. Follow the applicable method and verify the prepared solution as required.
Frequently Asked Questions
How do I calculate a dilution in µg/mL?
Use C₁V₁ = C₂V₂. Multiply the target concentration by the intended final volume, then divide by the stock concentration to find the stock volume. Subtract that volume from the final volume to find the diluent volume.
How many µg/mL are in 1 mg/mL?
There are 1000 µg/mL in 1 mg/mL, because 1 mg equals 1000 µg. Convert one concentration before using the equation if the units differ.
Can the target concentration be higher than the stock concentration?
Not by dilution alone. A dilution can only maintain or reduce concentration. A target above the stock gives no physically meaningful positive stock volume in this calculator.
Does the calculated diluent volume include the stock?
No. It is the additional diluent amount calculated as final volume minus stock volume. Together, stock and diluent volumes equal the stated final volume under the calculator’s volume-addition assumption.
Can I use this calculator for molarity?
Not directly. This calculator uses µg/mL. To work in mol/L, convert mass concentration using the substance’s molar mass, then apply a dilution calculation with matching concentration units.
Related
Formula used
in cs | Stock concentration | µg/mL | 1000 | 0.000001 in ct | Target concentration | µg/mL | 100 | 0.000001 in vf | Final solution volume | mL | 10 | 0.000001 out vs | Stock solution volume | mL | ct * vf / cs | 4 out vd | Diluent volume | mL | vf - vs | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s