molecalculator

Moles & Molar Mass

Standard Molar Volume of a Gas: Values and Formula

Calculator No. 01-5721 · Updated · Formula and assumptions shown below

Molar volume 22.4140 L/mol
Molar volume
0.022414 m^3/mol
= (8.31446261815324 × (Temperature + 273.15) ÷ Pressure) ÷ 1000
Gas volume
22.4140 L
= Amount of gas × (8.31446261815324 × (Temperature + 273.15) ÷ Pressure)
Amount of gas
1 mol
Set in the form below
You enter
Amount of gas (mol), Temperature (°C), Pressure (kPa)
You get
Molar volume (L/mol), Molar volume (m^3/mol), Gas volume (L)
Rounding
4 dp · 6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The standard molar volume of a gas is the volume occupied by one mole at specified temperature and pressure; there is no single value unless those conditions are stated. For an ideal gas, at 0 °C and 1 atm it is about 22.414 L/mol, while at the IUPAC standard pressure of 1 bar it is about 22.711 L/mol.

Formula

This calculator uses the ideal gas law, rearranged for molar volume:

Vm = RT/P

Here, Vm is molar volume in L/mol, R is the gas constant 8.31446261815324 J/(mol·K), T is absolute temperature in kelvins, and P is pressure in kilopascals. Because 1 kPa·L = 1 J, these units work directly together. The calculator converts Celsius to kelvins by adding 273.15 and uses the pressure entered in kPa. For a sample containing n moles, its ideal-gas volume is V = nRT/P, in liters.

The first result is molar volume, the volume per mole. The second expresses the same quantity in cubic meters per mole; 1 m3 = 1000 L. The third result is the total volume for the entered amount of gas.

Worked Example

Using the defaults—n = 1 mol, t = 0 °C and p = 101.325 kPa—first convert temperature:

T = 0 + 273.15 = 273.15 K

Then calculate the molar volume:

Vm = (8.31446261815324 × 273.15) / 101.325 ≈ 22.41397 L/mol

Rounded to four decimal places, the molar volume is 22.4140 L/mol. For one mole, total volume is 1 × 22.41397 ≈ 22.4140 L. In cubic meters per mole, this is 0.022414 m3/mol.

Assumptions

  • The gas is treated as ideal, with particles assumed not to have significant volume or intermolecular attraction.
  • Temperature is entered in °C and converted to K; pressure is entered as an absolute pressure in kPa.
  • The sample is a single gas or gas mixture described by the ideal-gas equation. Real gases can deviate, especially at high pressure or near condensation.

Why Standard Molar Volume Has More Than One Value

“Standard conditions” are conventions, not an unchanging physical state. A volume depends on both temperature and pressure, so a reference molar volume is meaningful only when both are specified. Older textbooks and many chemistry problems use standard temperature and pressure (STP) as 0 °C and 1 atm. Since 1 atm is exactly 101.325 kPa, the ideal-gas calculation gives approximately 22.414 L/mol.

IUPAC’s standard pressure is 100 kPa, or 1 bar, rather than 1 atm. At 0 °C and 100 kPa, the same formula gives about 22.711 L/mol. The temperature is the same in these two examples; the difference comes from the lower pressure in the 1-bar convention. Always check how a problem, data table or laboratory method defines its standard state.

A different convention sometimes called standard ambient temperature and pressure (SATP) uses 25 °C and 100 kPa. Under those conditions the ideal molar volume is about 24.790 L/mol. This is not a correction to the 0 °C figure; it is a different reference temperature.

How to Use the Calculator and Read the Result

Enter the gas amount in moles, temperature in degrees Celsius and absolute pressure in kilopascals. The default settings represent one mole at 0 °C and 1 atm. The first output is the volume per mole; the final output scales that value by the amount entered. For example, at the same temperature and pressure, 2 mol of ideal gas occupy about twice the volume of 1 mol.

  • Use absolute pressure, not gauge pressure. Gauge pressure is measured relative to the surrounding atmosphere; add atmospheric pressure to it before using this equation.
  • Use kelvins in the formula. The calculator handles the Celsius-to-kelvin conversion, but a hand calculation must use T in K, never the Celsius number directly.
  • Keep pressure units consistent. The displayed formula pairs R in J/(mol·K) with pressure in kPa and volume in liters.
  • Do not round intermediate values too early. Round the final result to match the precision of the measurements and the question.

For a gas mixture, the equation can be used with total pressure and total moles for an ideal mixture. If you need the volume of a particular component, use that component’s amount with the mixture’s temperature and total pressure only when the requested quantity and assumptions justify it; partial-pressure questions may instead call for the component’s partial pressure.

Ideal Gas Values and Real-Gas Limits

The result is a model prediction. Real molecules attract one another and occupy space, so measured behavior differs from the ideal-gas law. These effects are often small for gases at modest pressures and temperatures well above their condensation points, but they become more important at high pressure and near liquefaction. In such cases, a real-gas equation or measured compressibility factor may be needed.

Be especially careful when comparing a tabulated experimental molar volume with a textbook ideal value. The table may specify a particular gas, temperature, pressure, humidity condition or measurement convention. Water vapor can matter in gas collected over water, and the pressure of the dry gas is then less than the total pressure. The calculator does not correct for water vapor or non-ideal behavior.

Common Confusions and Applications

Molar volume is not the same as molar mass. Molar volume has units such as L/mol and describes space occupied; molar mass has units g/mol and describes mass per amount. The two can be combined to relate a gas’s density to its molar mass under stated conditions, but neither quantity alone determines the other.

Standard molar volume is useful in stoichiometry when a balanced reaction relates gaseous reactants or products to moles. Convert a known gas volume to moles using n = V/Vm, provided the temperature and pressure match the molar-volume value. Alternatively, use PV = nRT directly when the conditions are not one of the familiar reference conventions. For example, a volume measured at room temperature should not be converted with the 0 °C, 1-atm value without correcting for its actual conditions.

Frequently Asked Questions

What is the standard molar volume of a gas at STP?
With STP defined as 0 °C and 1 atm, the ideal-gas value is approximately 22.414 L/mol. Some sources use different standard conditions, so check the stated pressure and temperature.

Is standard molar volume always 22.4 L/mol?
No. About 22.4 L/mol applies to an ideal gas at 0 °C and 1 atm, usually rounded to three significant figures. At 0 °C and 1 bar, it is about 22.7 L/mol; at 25 °C and 1 bar, about 24.8 L/mol.

Why does pressure change molar volume?
At a fixed temperature, the ideal-gas law gives Vm = RT/P. Increasing pressure therefore decreases the volume per mole; lowering pressure increases it.

How do I calculate gas volume from moles?
For ideal behavior, calculate V = nRT/P, using n in mol, T in kelvins, P in absolute pressure, and units consistent with R. Or multiply moles by the molar volume for the same conditions.

Does the standard molar volume apply to every gas?
It is the ideal-gas value, which is independent of gas identity. Real gases do not all match it exactly; their deviations depend on the gas and the conditions.

Related

Formula used
in n | Amount of gas | mol | 1 | 0
in t | Temperature | °C | 0 | -273.15
in p | Pressure | kPa | 101.325 | 0.001
out vm | Molar volume | L/mol | 8.31446261815324 * (t + 273.15) / p | 4
out vm3 | Molar volume | m^3/mol | (8.31446261815324 * (t + 273.15) / p) / 1000 | 6
out v | Gas volume | L | n * (8.31446261815324 * (t + 273.15) / p) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →