Use this calculator to find the volume required to reach a target molarity from a known amount of solute and a known molar mass. Enter the solute mass, molar mass, and target concentration; the calculator returns the required final solution volume in liters and milliliters.
Formula
For a solution with a specified molarity, the required final volume follows from the definition of molarity:
V = m / (M × C)
- V is final solution volume in liters (L).
- m is solute mass in grams (g).
- M is solute molar mass in grams per mole (g/mol).
- C is target molarity in moles per liter (mol/L).
The calculator also converts liters to milliliters using 1 L = 1000 mL. In terms of amount of substance, the same calculation is V = n/C, where the number of moles is n = m/M. The calculator combines those two steps in its first output.
Worked Example
With the calculator’s defaults, the solute mass is 2.922 g, its molar mass is 58.44 g/mol, and the target concentration is 0.2 mol/L.
- Calculate the amount of solute: n = 2.922 g / (58.44 g/mol) = 0.05 mol.
- Calculate the required final volume: V = 0.05 mol / (0.2 mol/L) = 0.25 L.
- Convert to milliliters: 0.25 L × 1000 mL/L = 250.0 mL.
The required final volume is 0.250 L, or 250.0 mL. The outputs are rounded to three decimal places in liters and one decimal place in milliliters.
Assumptions
- The entered molar mass applies to the exact chemical form being weighed, including any hydrate or salt form.
- The target is molarity: moles of solute per liter of final solution.
- The calculation treats the solute amount as the stated mass divided by molar mass and does not account for purity, assay, or material lost during handling.
- No temperature correction or volume contraction is applied; practical solution volume can vary with temperature and composition.
What “Required Volume” Means
“Required volume” is the final volume the complete solution should occupy—not necessarily the amount of solvent to pour in. If a calculation gives 250 mL, it means the solute must be dissolved and the finished solution brought to a total volume of 250 mL. It does not mean adding the solute to 250 mL of water, because dissolving a substance can change the total volume.
The question may also refer to a different missing quantity. For example, a dilution problem may ask how much of a concentrated stock solution is needed to prepare a target solution. That calculation uses the dilution relationship C₁V₁ = C₂V₂, not the mass-based formula above. This page calculates the final volume from a known solute mass and target molarity.
When to Use the Calculator
Use it when the mass of a solute is known and you need to determine what final solution volume corresponds to a desired molarity. For instance, if you have 2.922 g of a substance with molar mass 58.44 g/mol and want a 0.2 mol/L solution, the required final volume is 250 mL.
The calculation is useful for checking a preparation plan or translating between mass and concentration. It does not tell you how to carry out a laboratory preparation, whether a compound is suitable for a particular use, or how to compensate for an impure sample. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Inputs, Units, and Common Mistakes
- Mass: Enter grams. Convert milligrams to grams before using the calculator: 500 mg = 0.500 g.
- Molar mass: Use g/mol for the actual formula and chemical form. A hydrate has a different molar mass from the corresponding anhydrous compound.
- Target concentration: Enter mol/L, not mM. Convert millimolar to molar by dividing by 1000; for example, 50 mM = 0.050 mol/L.
- Final volume: Read the first output in liters or the second in milliliters. The two are equivalent after the stated conversion.
- Rounding: Keep full precision while calculating, then round the volume to a sensible precision for the measurement method. Displayed digits do not imply that a solution can be prepared with matching accuracy.
A frequent mistake is to use a molar mass in kilograms per mole while entering mass in grams. The units must match the formula: grams divided by grams per mole gives moles. Another is to use the molecular weight of the wrong form—for example, an anhydrous salt instead of a hydrate—which changes the calculated amount of substance and therefore the volume.
Limits and Related Calculations
This formula assumes the mass represents the amount of pure solute. If the substance has a known purity fraction, the effective solute mass is the weighed mass multiplied by that fraction; enter that adjusted mass if the intended calculation requires it. The calculator does not apply this correction automatically, and an assay value or purity claim should come from an appropriate source.
For a stock dilution, use the stock concentration and desired final concentration instead: V₁ = C₂V₂/C₁, where V₁ is the stock volume, C₁ its concentration, V₂ the target final volume, and C₂ the target concentration. For a mass-based calculation where the desired final volume is already fixed, the corresponding solute mass is m = C × V × M. These equations answer related but distinct questions; choose the one that matches the known quantities.
Frequently Asked Questions
Is the required volume the amount of water to add?
No. It is the total final solution volume. Dissolve the solute and bring the solution to the calculated final volume according to the appropriate method.
How do I calculate volume from mass and molarity?
Divide the mass by the molar mass to obtain moles, then divide moles by molarity: V = m/(M × C). Keep the units in grams, grams per mole, and moles per liter.
Can I enter a concentration in mM?
Convert it to mol/L first by dividing by 1000. For example, 25 mM is 0.025 mol/L.
Why is the volume wrong if I use the anhydrous molar mass?
If the material is a hydrate or another chemical form, its molar mass differs. Using the anhydrous value gives an incorrect mole amount for the mass actually weighed.
Does this calculator work for diluting a stock solution?
Not directly. Stock dilution uses C₁V₁ = C₂V₂ because the amount is specified by the stock concentration and volume rather than by a weighed solute mass.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in c | Target molarity | mol/L | 0.2 | 0 out v | Required final volume | L | m / (mm * c) | 3 out vm | Required final volume | mL | v * 1000 | 1
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s